Sony PCS-1P Connection Sheet

Connection Sheet (LAN Connection)
System Setup
1
TV monitor**
2
AUDIO OUT AUX1– VIDEO IN –AUX2 AUDIO IN CAMERA UNIT
(MIXED)
100BASE-TX
VIDEO OUT
AUX MAIN– MONITOR– SUB RGB OUT 10BASE-T
IR OUT
1 2
4
LAN cable**
LAN
* supplied
** not supplied
2
Connect the camera.
Connect the Camera Unit and Communication
Terminal using the supplied camera cable.
TERMINAL VISCA OUT Camera Unit
Camera cable*
AUDIO IN CAMERA UNIT M Communication
(PLUG
1
Terminal
100BASE-TX
10BASE-T
RGB OUT
IR OUT
1 2
* supplied
© 2004 Sony Corporation Printed in Japan
Camera Unit
3
Data Solution Box
LINE OUT OUT AUX IN MIC 1 MIC 2 MIC 3 MIC 4 MIC 5 TO PROCESSOR RGB OUT
PCS-DSB1**
TERMINAL VISCA OUT
PCS-C1/C1P*
MIC
(PLUG IN POWER) ISDN UNIT WHITE
1 2 BOARD
Communication Terminal
DC 19.5V
PCS-P1/P1P
DSB
5
AC adaptor
Power cord*
PCS-AC195*
3
Connect the Data Solution Box.
Connect the Data Solution Box and Communication Terminal using the
cable supplied with the Data Solution Box.
MIC 1 MIC 2 MIC 3 MIC 4 MIC 5 TO PROCESSOR RGB OUT
Data Solution Box
Interface cable
(supplied with the PCS-DSB1)
AUDIO IN CAMERA UNIT M
Communication
(PLUG
1
Terminal
100BASE-TX
10BASE-T
RGB OUT
IR OUT
1 2
Used with the Data Solution Box for the first time, the Communication Terminal may
automatically upgrade the software of the Data Solution Box. While the upgrading message
is displayed on the monitor screen, be sure not to turn off the Communication Terminal.
Doing so may cause malfunction of the system.
* supplied
3-863-988-11 (1)
Let's connect
Notes
• Be sure to turn off all the equipment
before making any connections.
• Do not connect/disconnect the camera
cable with the power on. Doing so may
damage the Camera Unit or
Communication Terminal.
4
Connect the LAN cable.
Connect the Communication Terminal to a
LAN using a LAN cable (not supplied).
Communication
Terminal
N CAMERA UNIT MIC
ISDN UNIT
(PLUG IN POWER)
1 2
100BASE-TX
10BASE-T
DSB
IR OUT
1 2
UTP cable
(category 5, straight)**
For safety, do not connect the 100BASE-TX/10BASE-T
connector to a network that applies an excess voltage via
the 100BASE-TX/10BASE-T connector.
** not supplied
Video Communication System PCS-1/1P
1
Connect the TV monitor.
Connect the TV monitor and Communication Terminal
using the supplied audio cable and S-video cable.
AUDIO IN S-VIDEO IN
L R
TV monitor
Audio cable* S-video cable*
AUDIO OUT AUX1– VIDEO IN –AUX2 AUDIO IN
Communication
Terminal
(MIXED)
VIDEO OUT
AUX MAIN– MONITOR– SUB RGB OUT
* supplied
5
Connect the AC adaptor.
Connect the supplied AC adaptor to the Communication
Terminal, and then plug the power cord into a wall outlet.
Communication
Terminal
WHITE
BOARD
N CAMERA UNIT MIC
(PLUG IN POWER)
1 2
DC 19.5V
100BASE-TX
10BASE-T
DSB
IR OUT
1 2
to LAN
* supplied
• When connecting a second monitor,
use the VIDEO OUT MONITOR
SUB or the RGB OUT connector on
the Communication Terminal, or the
RGB OUT connector on the Data
Solution Box. For details, refer to the
Operating Instructions.
• The AUDIO OUT (MIXED) jack is
used to make an audio recording of
a conference. This is not used
during regular conferences.
ISDN UNIT
WHITE
BOARD
DC 19.5V
AC adaptor*
Power cord*
to a wall outlet
(100 -240V AC)