Download  Print this page

Sony PCS-1 System Integration Manual

Communication system
Hide thumbs

Advertisement

COMMUNICATION SYSTEM
PCS-1
PCS-1P
SYSTEM INTEGRATION MANUAL
1st Edition

Advertisement

Table of Contents
loading

  Related Manuals for Sony PCS-1

  Summary of Contents for Sony PCS-1

  • Page 1 COMMUNICATION SYSTEM PCS-1 PCS-1P SYSTEM INTEGRATION MANUAL 1st Edition...
  • Page 2 Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. PCS-1/PCS-1P...
  • Page 3: Table Of Contents

    3. Compatibility in LAN Network 3-1. Connection via Hub ... 3-1 3-2. Connection via Router ... 3-3 3-3. Connection via DHCP ... 3-5 3-4. Connection via Gatekeeper ... 3-7 3-5. Connection via DHCP and Gatekeeper ... 3-9 PCS-1/PCS-1P Table of Contents...
  • Page 4 During Use of Internal MCU Function (Specified Value) ... 4-2 4-1-4. During Use of Internal MCU Function (User Setting: When TCP port number is set to 3000 and when UDP port number is set to 3100) ... 4-2 4-2. Setting of PCS-1 and HUB ... 4-3 PCS-1/PCS-1P...
  • Page 5: Installation

    1-1. Caution on Installation 1-1-1. Lay Out the Videoconferencing Room Arrange it in consideration of the space of a camera and microphone when laying out the videoconferencing room. Camera Range represents the shooting area of the camera when the zoom has been extended fully.
  • Page 6 Highly directional range of microphone The ideal directional range of a microphone is shown below. The numeric value is a rough standard. Use the value as the reference of the videoconferencing room used. 1: For internal microphone 2: For extension microphone (PCS-A300) 3: For extension microphone (PCS-A1) 0.5 1...
  • Page 7 You can connect the optional PCS-A1 or PCS-A300 microphone to the System, allowing more persons to participate in the conference. Microphone layout examples Microphone built in the PCS-1/1P PCS-1/1P PCS-A300 microphones PCS-A300 PCS-A1 microphones...
  • Page 8 The range in which infrared rays reach is a maximum of about 5 m. Connect it with PCS-1/1P using a MONITOR OUT terminal when the infrared light emitter is used in excess of about 5 m.
  • Page 9 Installation range (Reference) If an image is disturbed in the range shown below, bring it near PCS-1/1P with the infrared light emitter of a documents stand turned toward PCS-1/1P. Infrared light emitter Infrared light emitter . Install so that the infrared light emitter of a document stand is linear in direction with the infrared photosensor of PCS-1/1P.
  • Page 10: Operating Environment

    Avoid direct light on the TV monitor. Light intensity on faces should be about 300 lux or more. If an inverter type or brightness-adjustable type of fluorescent lamp is used, the sensitivity of the Remote Commander may deteriorate. Installing the Communication Terminal and Camera PCS-1/PCS-1P...
  • Page 11: Flowchart Of Installation

    Start the power of the system and initialize. Initialize the related block. PCS-1/PCS-1P <Refer to “1-1. Caution on Installation” on page 1-1.> <Refer to “1-3. System Connections” on page 1-8.> <Refer to “1-4. Initialization” on page 1-10.> <“1-5. System Setting” on page 1-17.>...
  • Page 12: System Connections

    (PLUG IN POWER) ISDN UNIT WHITE BOARD 100BASE-TX DC 19.5V 10BASE-T IR OUT to DC19.5V to 100BASE-TX/ PCS-AC195 10BADSE-T AC adaptor UTP cable (category 5, straight) TV monitor to a wall outlet Power cord to wall outlet to LAN PCS-1/PCS-1P...
  • Page 13: When Used In Isdn

    (supplied with the PCS-B768) Audio S-video connecting connecting cable cable to S-video input to audio input supplied not supplied PCS-1/PCS-1P PCS-C1 Camera Unit VISCA OUT to TERMINAL Camera cable to CAMERA UNIT CAMERA UNIT (PLUG IN POWER) ISDN UNIT WHITE BOARD 100BASE-TX DC 19.5V...
  • Page 14: Initialization

    . Do not attempt to charge the batteries. . If you do not intend to use the Remote Commander for a long period of time, remove the batteries. . If battery leakage occurs, clean the battery compartment and replace all the batteries with new ones. 1-10 PCS-1/PCS-1P...
  • Page 15: Turning On/Off The Tv Monitor Together With The Communication Terminal

    Terminal If you use a Sony TV, insert the IR repeater under the remote sensor of the TV. Once you set the IR repeater, the TV will turn on or go to standby together with the Communication Terminal when you press the I/O button on the supplied Remote Commander.
  • Page 16: Adjust The Volume Of A Monitor Television

    1-4-3. Adjust the Volume of a Monitor Television Adjust the television side after the volume is adjusted on the PCS-1/1P side. 1. Press the volume/bright button of a remote controller and adjust so that the volume adjustment bar is in the center position 2.
  • Page 17: Turning On

    . The POWER indicator on the camera goes off when the system enters standby mode. . If you use a Sony TV monitor with the IR repeater installed under the remote sensor, the TV monitor will enter standby mode together with the Communication Angle Adj.
  • Page 18: When The Power Was First Turned On After Installation

    Enter your country code or region code with the number buttons on the Remote Commander. Protocol: Select the protocol of the ISDN line you are using. 4. Use the , , press the PUSH ENTER button. Cancel National ISDN Next Cancel button to select “Next”, then PCS-1/PCS-1P...
  • Page 19 ENTER button. 6. Use the , , button to select “Next”, then press the PUSH ENTER button. PCS-1/PCS-1P 7. Enter the sub-addresses. Only numerals are available for a sub-address. When you use one ISDN line, enter the same number both in the A1 and A2 text boxes (except for the USA and Canada).
  • Page 20 PUSH ENTER button. To go back to the previous wizard Press the , , press the PUSH ENTER button. button to select “Save”, then Save Previous Cancel button to select “Cancel”, then button to select “Previous”, then PCS-1/PCS-1P...
  • Page 21: System Setting

    Use of DSB List registration after conference termination T.120 PC address PCS-1/PCS-1P Contents of setting Select the line interface (LAN, ISDN, or voice telephone) used. Select “On” when connecting using a bonding interface through which the remaining lines can also be connected by only dialing one line when multiple ISDN lines are used.
  • Page 22 Select the mode for putting the monitor into the standby state or turning on the power when a Sony’s monitor is used. Usually, set to “Mode 1”. Set to “on” when receiving the camera control command from the remote side.
  • Page 23 (*1) : Displayed with the transmission and reception columns divided. The setting state of this side is displayed on the transmission column, and the reception enable state of this side is displayed on the reception column. PCS-1/PCS-1P Contents of setting Set the user number (E.164 number) registered in a gate keeper.
  • Page 24: Flowchart Of Opening Test

    <Refer to “1-6-1. Outgoing Procedure of ISDN” on page 1-21.> <Refer to “1-6-2. Incoming Procedure of ISDN” on page 1-23.> <Refer to “1-6-3. Outgoing Procedure of LAN” on page 1-24.> <Refer to “1-6-4. Incoming Procedure of LAN” on page 1-26.> PCS-1/PCS-1P...
  • Page 25: Outgoing Procedure Of Isdn

    Select “Dial” at the bottom of a menu using , , buttons of a remote controller and press the decide button, or press the connect/disconnect ( / ) of a remote controller. PCS-1/PCS-1P Screen , and Connect Phone Book...
  • Page 26 Picture on the remote site Meeting starts! The line is disconnected and the conference is terminated. The current display returns to a launcher menu. PCS-1/PCS-1P...
  • Page 27: Incoming Procedure Of Isdn

    Item Operation Incoming from the remote side <For automatic response> <For manual response> Remote disconnection PCS-1/PCS-1P Screen An incoming sound occurs. “Incoming” is displayed on the Picture on the local site screen.
  • Page 28: Outgoing Procedure Of Lan

    LAN Bandwidth 1024 Kbps Save During connection, “Start meeting” is displayed, and the remote voice and image are heard and displayed from the monitor television. “Outgoing (LAN)” is displayed on the screen. Line I/F LAN Bandwidth 1024 Kbps Save PCS-1/PCS-1P...
  • Page 29 Select “OK” using a button of a remote controller and press the decide button, or press the connect/disconnect ( / ) button of a remote controller again. PCS-1/PCS-1P Screen Remarks (Confirmation item) The ON LINE lamp (blue) lights. “Start meeting” is displayed, and the...
  • Page 30: Incoming Procedure Of Lan

    Meeting starts! The message of conference termination is displayed on the screen and the current display returns to a Connect launcher menu. Phone Book Dial Menu Angle Adj. Show Help IP:0.0.0.0 ISDN:012345678912 Video:Main Audio:MIC(INT)+AUX Remarks (Confirmation item) button PCS-1/PCS-1P...
  • Page 31: Maintenance

    Select “Line type” using , , , and remote controller and press the decide button. Then, select “ISDN” using the decide button. PCS-1/PCS-1P Section 2 Maintenance 4. Select the number of lines used. Select “Number of lines used” using , , buttons of a remote controller and press the decide button.
  • Page 32: Separation Of Components

    An image on the remote side is not displayed after a line is connected. An image cannot be transmitted to the remote side after a line is connected. SS-01 SS-02 SS-03 SS-04 SS-05 SS-06 SS-07 SS-08 SS-09 SS-10 SS-11 SS-12 SS-13 SS-14 SS-15 PCS-1/PCS-1P...
  • Page 33 1. The power is not turned on even if the power switch on the side panel is pressed. cord properly connected? (green) lamp light? Proceed to “5. The power of a monitor television is not turned on during the power-on sequence”. PCS-1/PCS-1P SS-01 Is power Connect it properly. Does POWER Communication terminal...
  • Page 34 Communication terminal is defective. SS-02 Proceed to “1. The power is not turned on even if the power switch on the side panel is pressed”. Is initial Communication terminal is defective. Remote controller’s battery is exhausted or remote controller is defective. PCS-1/PCS-1P...
  • Page 35 ISDN modular cable of ISDN unit is connected, light in red? Communication terminal is defective. PCS-1/PCS-1P SS-03 Turn on power switch on side panel. Is power Proceed to “2. The power is not turned on even if the I/O button of a remote controller is pressed”.
  • Page 36 Verify whole system including network administrator. SS-04 light? Turn on power switch on side panel. Proceed to “2. The power is not turned on even if the I/O button of a remote controller is pressed”. Connect it properly. Communication terminal is defective. PCS-1/PCS-1P...
  • Page 37 5. The power of a monitor television is not turned on during the power-on sequence. Is the main power switch of monitor TV turned on? Is the monitor TV compatible with this unit (made by Sony)? Are the connection and location of IR repeater correct? Does the setting of “IR repeater mode”...
  • Page 38 TV and the video input setting of the monitor correct? Communication terminal is defective. Set the video signal input to “main”. Camera unit is defective. Communication terminal is defective. Connect and set the monitor TV correctly. PCS-1/PCS-1P...
  • Page 39 Can zoom button or volume button be operated? Communication terminal is defective. PCS-1/PCS-1P Proceed to “2. The power is not turned on even if the I/O button of a remote controller is pressed”. buttons and Remote controller is defective.
  • Page 40 8. The camera on the local side cannot be operated. unit properly connected to (green) lamp of camera Communication terminal is defective. 2-10 SS-08 Is camera communication terminal? Connect it properly. Does POWER unit light? Camera unit is defective. PCS-1/PCS-1P...
  • Page 41 ISDN unit light in yellow proportionally to number of connected lines when line is connected to ISDN unit by number of connected lines? Communication terminal is defective. PCS-1/PCS-1P SS-09 Are contents of side.) connected? Does STATUS in green? Communication terminal or ISDN unit is defective.
  • Page 42 Communication terminal is defective. 2-12 SS-10 Are the setting Set it properly. Are the connection of LAN IP address and net mask correct? Connect and set correctly. PCS-1/PCS-1P...
  • Page 43 Is the volume of the monitor TV turned down? Communication terminal is defective. PCS-1/PCS-1P SS-11 Turn up the volume. Ask the other end of the line to turn on the microphone. Is the TV correct? Connect it properly.
  • Page 44 Is audio signal output from connected equipment? Connected equipment is defective. Is PCS-A1/PCS-A300 microphone connected? Connect PCS-A1/ PCS-A300 microphone. Connected equipment is defective. Is microphone OFF canceled? Set microphone to ON. Communication terminal, data solution box, or PCS-A1/PCS-A300 microphone is defective. PCS-1/PCS-1P...
  • Page 45 Is video signal output from equipment connected to AUX1 and AUX2 terminals? Connected equipment is defective. Communication terminal is defective. PCS-1/PCS-1P Press input selector button of remote controller and select input properly using joystick. Is power PCS-DS150 on? Does obstacle exist...
  • Page 46 Check the terminal of the other end. 2-16 SS-14 Is the video AUX? Connect correctly. Can the controller? Failure of the communication terminal Is the image of the other end communication end? Communication terminal is defective. PCS-1/PCS-1P...
  • Page 47 Check the terminal of the other end. PCS-1/PCS-1P SS-15 Press the input selector button on the remote controller and select the input correctly using the joystick.
  • Page 48: Operation Log

    1M byte in a memory stick (refer to the saving of system log on page 56). Operation log using commercial PC (1) Connect an AUX CONTROL terminal and PC to the right on the front panel of PCS-1/1P. Start the power of PCS-1/1P and PC.
  • Page 49 (1) Click “Start menu”, “Accessory”, “Communication”, and then “Hyper terminal”. (2) Enter “VT100” in “Name (N)”, select any icon, and click the “OK” button. 2-19 PCS-1/PCS-1P...
  • Page 50 (3) Select “COM1” in “Connect To” and click the “OK” button. (4) Set the baud rate as described below and click the “OK” button. Bit/s: 38,400 Data bit: Parity: None Stop bit: Flow control: Xon/Xoff 2-20 PCS-1/PCS-1P...
  • Page 51 (5) Click “Capture Text” from a “Transfer” menu. (6) Set the saving place and name of a log file and click “Start”. 2-21 PCS-1/PCS-1P...
  • Page 52 (7) After logging, click “Stop” from “Capture Text” in a “Transfer” menu. (8) Double-click the extracted log file to view a log. 2-22 PCS-1/PCS-1P...
  • Page 53 PC directly using a LAN cross cable. First, connect PCS-1/1P and PC to LAN, or connect them directly using a cross cable and set LAN of IP. After that, transmit ping from PC to PCS-1/1P and confirm that a reply is returned from PCS-1/1P.
  • Page 54 (2) Enter ping, and then enter the IP address of PCS-1/1P after spacing out. Press the [Enter] key and confirm that a reply is returned. After confirmation, close the command prompt. (3) Click “Start menu”, “Accessory”, “Communication”, and then “Hyper terminal”.
  • Page 55 (4) Enter “LAN” in “Name:”, select any icon, and click the “OK” button. (5) Select “TCP/IP (Winsock)” in “Connect To”, enter the IP address of PCS-1/1P in “Host address:”, and click the “OK” button. 2-25 PCS-1/PCS-1P...
  • Page 56 (6) Click “Capture Text” from a “Transfer” menu. (7) Set the saving place and name of a log file and click the “Start” button. Example of name: PCS-1LOG.txt 2-26 PCS-1/PCS-1P...
  • Page 57 (8) The message below is displayed on the hyper terminal screen. PCS-1 Telnet Server login: Enter sonypcs and press the Enter key. Password: is then displayed. Press the Enter key again. A log begins to be extracted. (9) After log extraction is completed, click “Stop” from “Capture Text” in a “Transfer” menu.
  • Page 58: Updating Of Software

    Select “Set” and confirm “Host version” in a device information menu. Return to the launcher menu and turn off the power switch on the rear panel of this unit. Turn on the power switch again and reconfirm “Host version”. PCS-1/PCS-1P...
  • Page 59: Service Mode

    2-5. Service Mode In the service menu of PCS-1/1P, data can be saved in the Memory Stick of an address book using a commercial Memory Stick or read from a Memory Stick (overwritten in the current data). 1. Continuously press the menu button of a remote controller and display a “Set”...
  • Page 60 Sets the Type Of Service (TOS) bit value to a transmission packet. Consult the network administrator for the set value. Set using an initial value. The LAN interface mode is Auto Negotiation. Reception packet loss indicator display ON TOS0 PCS-1/PCS-1P...
  • Page 61 Memory Stick. After execution, a file is created in the area below in a memory stick. ¥MSSONY¥PRO¥TVCONF¥SETUP¥PCS_STUP.CSV This file can be edited using Microsoft Excel. PCS-1/PCS-1P 9) Loading of setting The set information (¥MSSONY¥PRO¥TVCONF¥SETUP¥PCS_STUP.CSV) recorded in a Memory Stick is overwritten in the set menu of the main unit.
  • Page 63: Compatibility In Lan Network

    49152 (Enter the port number specified by the network administrator when the port number used is set to “User setting”.) 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.100.10.20. PCS-1/PCS-1P Section 3 LAN2 Teleconference terminal B 192.100.10.20...
  • Page 64 B in it for an IP address, and other required items. After that, register teleconference terminal B in the address book and initiate a call. Or set LAN for a line type and IP address 192.100.10.20 of teleconference terminal B for an IP address by dialing, and then initiate a call. PCS-1/PCS-1P...
  • Page 65: Connection Via Router

    49152 (Enter the port number specified by the network administrator when the port number used is set to “User setting”.) 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.100.20.20. PCS-1/PCS-1P 192.100.20.1 Router Teleconference terminal B 192.100.20.20...
  • Page 66 B in it for an IP address, and other required items. After that, register teleconference terminal B in the address book and initiate a call. Or set LAN for a line type and IP address 192.100.20.20 of teleconference terminal B for an IP address by dialing, and then initiate a call. PCS-1/PCS-1P...
  • Page 67: Connection Via Dhcp

    49152 (Enter the port number specified by the network administrator when the port number used is set to “User setting”.) 2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.100.20.20. PCS-1/PCS-1P Router Router DHCP...
  • Page 68 B in it for an IP address, and other required items. After that, register teleconference terminal B in the address book and initiate a call. Or set LAN for a line type and the IP address of teleconference terminal B for an IP address by dialing, and then initiate a call. PCS-1/PCS-1P...
  • Page 69: Connection Via Gatekeeper

    2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.100.20.20. 3. Confirm that Registration Confirm is displayed at the bottom of page 2/5 in the LAN set menu of teleconference terminal B. PCS-1/PCS-1P 192.100.20.1 Router Router...
  • Page 70 200 of teleconference terminal B in it for an IP address, and other required items. After that, register teleconference terminal B and initiate a call. Or set LAN for a line type and user name PCS1B or user number 200 of teleconference terminal B for an IP address by dialing, and then initiate a call. PCS-1/PCS-1P...
  • Page 71: Connection Via Dhcp And Gatekeeper

    2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is 192.100.20.20. 3. Confirm that Registration Confirm is displayed at the bottom of page 2/5 in the LAN set menu of teleconference terminal B. PCS-1/PCS-1P Router Router DHCP...
  • Page 72 B and initiate a call. Or set LAN for a line type and user name PCS1B or user number 200 of teleconference terminal B for an IP address by dialing, and then initiate a call. 3-10 PCS-1/PCS-1P...
  • Page 73: Technical Data

    The port number that PCS-1/1P uses is determined by the value input to TCP and UDP port numbers when the port number used in a LAN set menu is set as “User setting”. For example, PCS-1/1P uses the port number below during opposed connection when a TCP port number is set to 3000 and when an UDP port number is set to 3100.
  • Page 74: During Use Of Internal Mcu Function

    The port number that PCS-1/1P uses is determined by the value input to TCP and UDP port numbers when the port number used in a LAN set menu is set as “User setting”. For example, PCS-1/1P that operates as internal MCU uses the port number below during opposed connection when a TCP port number is set to 3000 and when an UDP port number is set to 3100.
  • Page 75: Setting Of Pcs-1 And Hub

    PCS-1 and Catalyst 2950. When the HUB is set to 100FULL or 10FULL, change the setting of HUB or adjust the PCS-1 setting to HUB. Refer to “2-5. Service Mode” for the setting procedure of the PCS-1.
  • Page 78 PCS-1 (UC) Sony Corporation PCS-1P (CE) E 2003. 7 22 B&P Company 9-968-036-01 ©2003...

This manual is also suitable for:

Pcs-1p