Page 1 File No. SME18003400 R180821V5800-TTEC Ver00F_2018-10...
Page 2 , NetWare and NDS are trademarks of Novell, Inc. • e-STUDIO, e-BRIDGE, and TopAccess are trademarks of Toshiba TEC Corporation. • Other company names and product names in this manual are the trademarks of their respective companies. © 2018 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION.
Page 3 GENERAL PRECAUTIONS REGARDING THE SERVICE The installation and service shall be done by a qualified service technician. 1. Transportation/Installation - When transporting/installing the equipment, employ two or more persons and be sure to hold the positions as shown in the figure. The equipment is quite heavy and weighs approximately 78.1 kg (172.2 lb.), therefore pay full attention when handling it.
Page 4 - Do not use an ozone generator near the MFP. Or, place any ozone generator as far away from　the MFP as possible. 2. General Precautions at Service - Be sure to turn the power OFF and unplug the power cable during service (except for the service should be done with the power turned ON).
Page 5 Do not allow a short-circuit and do not use the parts not recommended by Toshiba TEC Corporation. 5. Cautionary Labels - During servicing, be sure to check the rating plate and cautionary labels to see if there is any dirt on their surface and if they are properly stuck to the equipment.
Page 6 Revision Record Ver00 <2018.10.19> Page Contents Initial release...
Page 7 • How to make the text look sharper on the copy The Toshiba MFPs are factory-configured to provide image quality settings that satisfy the majority of customers. However, these settings may not be necessarily optimal for the specific needs of all customers.
Page 8 Purpose of the Imaging Manual Icons The following icons used in this manual denote the following: • Copy——— An adjustment having an effect on copying in the Black mode (excluding the Image Smoothing mode) • Printer——–An adjustment having an effect on Black and White mode printing * The adjustment will be effective, if “Black and White”...
Page 9: Table Of Contents
2.21 To Avoid Copying Blank Page of Original Scanned with DF ........2-90 2.22 To Obtain Image in Even Density Level ..............2-92 2.23 To Improve Reproducibility of Red Seal Color ............2-94 © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 10 To Decrease the Image Density and Save Toner ............3-78 3.8.1 To Print in the Toner Saving Mode................ 3-78 3.8.2 To Adjust the Image Density in the Toner Saving Mode ........3-81 To Ignore Blank Pages for Printing................3-84 e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 11 5.12 To Change Judgment Area of [Omit Blank Page] and [Auto Color] (To make judgment properly for originals whose images are only located near the edges)..5-27 5.13 To Make a Scan by Removing all Colors other than Black ......... 5-29 © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 13: General Adjustments - Copying, Printing And E-Filing (Output From Box)
A privilege to perform automatic calibration is set to Administrator by default but this can be changed to the User. For how to change the privilege, refer to the MFP Management Guide. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 14 "3.3 To Maintain a Steady Color Balance". After performing automatic calibration, print and check the image quality. If further image quality adjustments are necessary, go to step (2) to adjust the transfer (2nd transfer) roller bias output. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 15 (d) The message “Set Auto Calibration Yes or No.” appears. Press [Yes]. After performing simple calibration, print the image and check its quality. If further image quality adjustments are necessary, carry out the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 16 Thick paper 2 Thick paper 3* Special paper 1 Back 05-2935 2 to 8 0 to 10 Special paper 2 Recycled paper Thick paper 4* Thin paper* Envelope Special paper 3* e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 17 On the other hand, the setting value should be decreased, when you print on thin paper. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 18 (for codes 05-2934 to 2937) to the default (setting value: 5) and then perform the adjustment again. • When replacing any consumable, refer to the relevant information in the Service Manual. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 19: To Adjust The Density On A Solid Colored Image
• When the value becomes larger than the present one, and the solid image becomes darker. When it becomes smaller, the image becomes lighter. The value must fall within a range of “- 50” and “+50” from the default. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 20 60 to 80 g/m² Max. 60 lb. Cover Thick paper 81 to 105 g/m² Max. 110 lb. Index Thin paper* 52 to 59 g/m² 14 to 16 lb. Bond * e-STUDIO2515AC/3015AC/3515AC/4515AC/5015AC only e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 21 • The effects of adjustment may vary, depending on the usage pattern of the consumables, such as the developer material and drum, and the installation environment of the MFP. • When replacing any consumables, refer to the relevant information in the Service Manual. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 22 • For further information regarding the PM support mode, refer to the Service Manual. Be sure to reset the counter. Otherwise, it may cause a loss in performance, including degradation in the image quality and a reduction in the life of the consumables. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-10...
Page 23 • The effect of the adjustment may vary, depending on the usage pattern of the consumables, such as the developer material and drum, and the installation environment of the MFP. • When replacing any consumable, refer to the relevant information in the Service Manual. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-11...
Page 24: To Achieve The Image Quality Most Suitable For The Paper Used (To Eliminate Blur And Graininess From An Image)
The code to use varies depending on the paper type. Adjust the value for [05] code corresponding to the paper type for which you would like to improve the image quality. Set the value within a range of “2” to “8” to optimize the Low/Middle density. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-12...
Page 25 Thick paper 3* Transparency (OHP film) Black Front 05-2936 2 to 8 0 to 10 Special paper 1 Special paper 2 Recycled paper Thick paper 4* Thin paper* Envelope Special paper 3* © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-13...
Page 26 If further image quality adjustment is necessary, go to step (3). (2) If the image on the high density area looks grained on plain paper other than the TOSHIBA- recommended one is used, select “recycled paper” as a paper type.
Page 27 Color 2510AC Black e-STUDIO e-STUDIO 2515AC/ 2515AC/ 3015AC/ 3015AC/ Center Recycled 3515AC/ 08-5293 9 to 11 0 to 22 3515AC thermistor paper Color 4515AC/ 5015AC e-STUDIO 4515AC/ 5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-15...
Page 28 [2934] to [2937] (bias offset) and [08] codes [5293] to [5294] (fusing temperature during printing) back to the default ones. Then perform the adjustment again. • When replacing any consumable, refer to the relevant information in the Service Manual. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-16...
Page 29: To Minimize Variations In The Image Quality Under The Operating Conditions (To Optimally Program Image Quality Control)
Before adjustment After adjustment The image contrast varies, depending on the date and time when copying or printing The image quality is constantly maintained. is performed or the type of job. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-17...
Page 30 This control is performed with a simple calibration operated from the control panel. * 2. The control with the simple correction takes approx. 15 seconds, but its correction accuracy is not as high as the one in the Full Mode. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-18...
Page 31 Difference in relative humidity 5%R.H. 10%R.H. (default) • After setting the value for code 08-2505, forcibly perform image quality control, as follows: Select [05 ADJUSTMENT MODE]. Select code [2742]. Press the [START] button. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-19...
Page 32 08-2507. • After setting the value for code 08-2507, forcibly perform image quality control, as follows: Select [05 ADJUSTMENT MODE], select code [2742], and then press the [START] button. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-20...
Page 33 *7.To start the Short Mode at every 30 pages, set the value to “30” for both 08-2497 and 08-9199. However, setting a too-short interval will use up too much toner, even though the consumption in the Short Mode is approximately a quarter of that in the Full Mode. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-21...
Page 34 • Changing this setting improves the stability of the image quality. However, a long application of this change affects the life of consumables. It is recommended to make only a minimal change and then return to the default value immediately. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-22...
Page 35 • After replacing any consumable, remember to reset the counter corresponding to it to “0”. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-23...
Page 36 Otherwise, it may cause a loss in MFP performance, including slowdown in the copying or printing speed. • When replacing any consumable, refer to the relevant information in the Service Manual. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-24...
Page 37: To Correct Out-Of-Registration Colors
(2) Load the thick papers in the drawer. (Paper weight: 106 to 256 g/m² / 29 to 80 lbs (Cover) / 90 to 140 lbs (Index)) (3) Select the paper type of the thick paper loaded in the drawer. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-25...
Page 38 Pattern A for out-of-registration colors Patch eliminated trailing edge Paper feeding speed faster than transfer belt rotating speed Page number Paper feeding direction Black belt at the leading edge in the paper feeding direction e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-26...
Page 39 (b) Select code [104], and then press [TEST PRINT]. Check all the patches on the second page of the printed test print pattern to check whether the misaligned colors have been improved. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 40 • Out-of-registration colors cannot always be perfectly corrected; this depends on the type of text or lines to print. • Also, refer to the relevant information in the Service Manual for further information regarding color registration control procedures. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-28...
Page 41: To Adjust Printing Positions On Front And Back Sides In The Duplex Mode
[F] Secondary scanning data writing 52 ± 0.5 mm 4.2 ± 0.5 mm start position at duplexing *1: e-STUDIO2515AC/3015AC/3515AC/4515AC/5015AC only *2: Use this chart to adjust the void width match. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-29...
Page 42 (5)Make a test copy and check the image copied. To check the printed image, turn off the power and then back on, and then print the image. If the image is not in the desired reproduction ratio, repeat steps (2) to (4). e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-30...
Page 43 In this procedure, it is recommended to use the print sample (05-316, 04-141, 04-410) as shown below. ③15m m ⑦15m m Front side ④15m m ⑧15m m Center position (top-bottom and left-right symmetric) ②15m m ⑥15m m Rear side ①15m m ⑤15m m © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-31...
Page 44 Change its position to the adjustment hole [4] and move the fuser unit guide rail (front) [2] up or down. (Guideline of the movement: One scale) • There is a 0.5 mm wide scale at the position indicated by [5]. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-32...
Page 45 Loosen 1 screw [1] on the fuser unit front guide rail. Remove 1 screw [2] and replace it in the adjustment hole [3]. Move the fuser unit front guide rail up or down (one step). • 0.5 mm scale [4] © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-33...
Page 46 Front side Rear side When this tilted image is printed in the duplex mode, image positions on the front and back sides become as shown below. Front side Back side e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-34...
Page 47 1.General Adjustments – Copying, Printing and e-Filing (Output from Box) Adjust the tilted images of leading edge When a printed image at the leading edge of paper is tilted as shown below, correct this by the following steps. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-35...
Page 48 (4) Loosen 5 screws [1]. (5) Move the frame [2] to the right or left to adjust its position. Remark: • Up to 1 mm is adjustable (0.5 mm for the right and left). e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-36...
Page 49 [6] The screw hole to use when the value of “A-B” is +0.5 mm (“+0.5” is marked) [7] The screw hole to use when the value of “A-B” is -0.5 mm (“-0.5” is marked) © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 50 Fig. C: The scale position is aligned at the center. Fig. D: The scale position is aligned at the fifth one on the front side from the center. (3) Loosen 2 screws [8]. (4) Remove 1 screw [9]. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-38...
Page 51 Fifth -0.7 -0.65 Sixth Sixth -0.84 -0.78 Seventh Seventh -0.98 -0.91 Eighth Eighth -1.12 -1.04 Moving approx. Moving approx. Remarks 0.14 mm per 1 0.13 mm per 1 scale scale © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-39...
Page 52 • Move the LSU holder [1] to the rear side so that its scale position of the second one on the front side is aligned to that for the frame [2]. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-40...
Page 53 For details, refer to “6.7.2. Adjustment of image tilting at the leading edge [2] Adjustment of the tilted volume by 0.5 mm with a simplified method” in the Service Manual. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 1-41...
Page 54 “0”, if minor deviations occurring during continuous printing are included. However, the amount of the deviation between the front and back sides can be reduced to approximately 0.5 mm to 1.5 mm by using this adjustment. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 1-42...
Page 55: Copier-Specific Adjustments
*2: Press [Mono Color] in the image menu of the touch panel. *3: Press [Twincolor Copy] in the image menu of the touch panel. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 56 Image Originals with text and  (especially originals Smoothing photographs mixed requiring higher reproducibility on photos). * Black mode only.  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 57: To Copy Text Clearly (To Eliminate Faint, Smudged Or Blurred Text)
The procedure to use varies, depending on whether to adjust the copy image quality in the Black mode, Full color mode. Refer to the procedure corresponding to the user’s particular request. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 58: To Adjust The Copy Image Quality In The Black Mode
One step in the indicator corresponds to “20” of the setting value in [05] code. After the setting value is changed, make a copy and confirm the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 59 Setting value “103”: -100 -100 Since “-25” is assigned to the center, the image quality remains the same even if the indicator is changed from “-3” to “-4”. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 60 • Note that if a too small setting value is set, the life of the supplies may be shortened. After increasing the copy density, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 61 After changing the value, make a copy and check the image quality. If further image quality adjustments are necessary, reset all the values changed in steps (1) to (8) above to the default ones and then follow the next step. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 62 (10) Select [08 SETTING MODE]. Change the value for subcode 3 or 7 of code [2620]. • This adjustment is available only for e-STUDIO2010AC. • This adjustment also influences the printing and fax functions as well as the copying function.
Page 63 K toner used compared with that for the other colors, or it may create a difference in the reproducibility of halftones. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 64: To Adjust The Copy Image Quality In The Full Color Mode
• The code to use varies according to the original mode or the manual/automatic density setting. Select the [05] code for the original mode in which the image quality is to be changed, and start the adjustment start from the setting value “128”. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-10...
Page 65 Changing the values for these codes will change the sharpness intensity, when the [Sharpness] indicator in the [Image] menu is set to the center. Remember that 1 step of the indicator will © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 66 • For the User Custom mode, refer to "2.19 To Program Frequently Used Copy Settings (To use Custom Mode)". • The setting content of the value “5” is the same as that for the default value “0”. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-12...
Page 67 “8” or “9” first to increase it. Then check the copy image and increase or decrease the value further so that the image will be adjusted finely. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 69: To Closely Match The Color Balance Of The Original
Then perform other procedures. • Both the service technician and the user can perform procedures (1) to (3). • Only the service technician must perform procedure (4) and (5). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-15...
Page 70 (Yellow). Press [-] at R (Red). Then the tint of R (Red) will be closely matched with that of M (Magenta). (d) Press [OK]. After adjusting the hue, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-16...
Page 71 Setting a larger value: The tint of Green becomes closer For adjusting the tint of to that of C (Cyan). Green Setting a smaller value: The tint of Green becomes closer to that of Y (Yellow). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-17...
Page 72 • The value for the code corresponding to the original mode (Text/Photo, Text, or Printed Image) will affect the copy image quality in the Full color mode and the Auto Color mode. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 73 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-19...
Page 74: To Improve The Reproducibility Of Gray
For how to change the privilege, refer to the MFP Management Guide. After performing automatic calibration, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-20...
Page 75 • The subcode varies according to the area where the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. Subcode Area where the density is adjusted Low density area Middle density area High density area © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-21...
Page 76 3: The gray tone becomes a more bluish one.  Caution after the adjustment Nothing in particular  Remarks The setting content of the values “2” and “4” is the same as that for the default (“0”). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-22...
Page 77: To Copy In Vivid Colors
• Only the service technician must perform procedure (4) and (5). • Only if the vividness of R (Red) is still insufficient even after procedures (1) to (4) have been used, the service technician must perform procedure (6). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-23...
Page 78 Full color and Auto Color modes. • The subcode varies according to the area where the hue is adjusted. Set the subcode for the area to be adjusted by referring to the following below. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-24...
Page 79 Full color mode and the Auto Color mode. • The setting value “25” corresponds to one step in the adjustment on the control panel. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 80 Therefore, perform the adjustment, being aware that the image quality of all future printouts will be changed, when printing out originals other than the one that is used for the adjustment. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-26...
Page 81 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-27...
Page 82: To Make The Pale Area Of The Original Look Darker And Sharper (To Improve The Highlight Reproducibility)
After increasing the background density, copy and check the copy image quality. With the background density set to the maximum, if further image quality adjustments are still necessary, the service technician must perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-28...
Page 83 After increasing the copy density, copy and check the copy image quality. With the copy density set to the maximum, if further image quality adjustments are still necessary, the service technician must perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-29...
Page 84 Full color mode and the Auto Color mode. • Before the User custom mode is used, enable this function by referring to "2.19 To Program Frequently Used Copy Settings (To use Custom Mode)"”. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-30...
Page 85 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-31...
Page 86: To Eliminate The Background Color / To Copy Dark Text By Eliminating Fogs Around It
The procedure to use varies, depending on whether to adjust the copy image quality in the Black mode or the Full color mode. Refer to the procedure corresponding to the user’s particular request. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 87: To Adjust The Copy Image Quality In The Black Mode
0 to 255 Drop Out Color 05-7187 User Custom 05-7189 Gray-Scale 05-7193 • Set the value in increments of approximately 20, while checking the copy image until the optimum value is obtained. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-33...
Page 88 Therefore, carefully perform the adjustment, while checking the copy image.  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-34...
Page 89: To Adjust The Copy Image Quality In The Full Color Mode
After adjusting the background density, copy and check the copy image quality. If further image quality adjustments are still necessary, or background elimination is necessary according to color, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-35...
Page 90 But it will not affect the background density. Therefore, never change the value for the high density area. Subcode Area where the density is adjusted Low density area Middle density area © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-36...
Page 91  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-37...
Page 92: To Avoid Copying The Image Seen Through The Back Of A Page Printed On Thin Paper
The procedure to use varies, depending on whether to adjust the copy image quality in the Black mode or the Full color mode. Refer to the procedure corresponding to the user’s particular request. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 93: To Adjust The Copy Image Quality In The Black Mode
“25” for the [05] code corresponds to one step in the background adjustment on the control panel. After adjusting the background density, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-39...
Page 94 Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality and a reduction in the life of the consumables. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-40...
Page 95: To Adjust The Copy Image Quality In The Full Color Mode
After adjusting the background density, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-41...
Page 96  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-42...
Page 97: To Eliminate Moiré
Then perform other procedures. • Both the service technician and the user can perform procedures (1) and (2). • Only the service technician must perform procedure (3). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-43...
Page 98 "2.19 To Program Frequently Used Copy Settings (To use Custom Mode)". After changing the default original mode option, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-44...
Page 99 [05] code is “103” (“-25” from the default value), the limit of the steps in the soft side of the indicator is “-3”. If the step is set at “-4”, the image quality will not be changed. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 100 Nothing in particular.  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-46...
Page 101: To Copy Sharply (To Enhance Sharpness)
Press [Sharp] to increase the sharpness intensity. After increasing the sharpness intensity, copy and check the copy image quality. If further image quality adjustment is necessary, go to the next step. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-47...
Page 102 [05] code is “153” (“+25” from the default value), the limit of the steps in the sharp side of the indicator is “+3”. If the step is set at “+4”, the image quality will not be changed. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 103 Nothing in particular.  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in copier performance, including degradation in the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-49...
Page 104: To Make Photo Edges Look Softer
Then perform other procedures. • Both the service technician and the user can perform procedures (1) and (2). • Only the service technician must perform procedures (3) to (5). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-50...
Page 105 (For instance, if the center value is decreased by “25” (softer), the value of each step of the indicator will also be decreased by “25” (softer).) © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-51...
Page 106 • Set the value in increment of 1, while checking the copy image until the optimum value is obtained. After adjusting the maximum color density of the text, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-52...
Page 107 Therefore, carefully perform the adjustment, while checking the copy image.  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-53...
Page 108: To Make Solid Filled Bold Text (Logo) Highly Colored
The procedure to use varies, depending on whether to adjust the copy image quality of a black or colored logo. Refer to the procedure corresponding to the user’s particular request. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-54...
Page 109: To Adjust The Copy Image Quality Of A Black Logo
After adjusting the tint of black, copy and check the copy image quality. If further image quality adjustment is necessary even after the tint of black was set to the maximum, the service technician must perform the next step. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-55...
Page 110 The adjustment may possibly cause the highly or deeply colored area, such as in a photo, to become blurred on the copy. Also, it may also cause offset failure, grained images and degradation in gradation. Therefore, carefully perform the adjustment, while checking the copy image. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-56...
Page 111: To Adjust The Copy Image Quality Of A Colored Logo
After selecting the Text or Map mode, copy and check the copy image quality. If further image quality adjustments are still necessary, the service technician must perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-57...
Page 112 The adjustment may possibly cause a dark-colored area, such as in a photo, to become blurred on the copy. Also, it may also cause offset failure, grained images and degradation in gradation. Therefore, carefully perform the adjustment, while checking the copy image. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-58...
Page 113: To Sharply Contrast The Hues Of Highlighters On The Copy
To reproduce the hues of similar highlighters, such as yellow and green, while producing sharp contrasts on the copy, perform color adjustment (color balance adjustment or RGB adjustment). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-59...
Page 114 (Yellow). Set 0 for R (Red). Then the tint of the red will be closely matched with that of M (Magenta). After adjusting the hue, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-60...
Page 115 • The subcode varies according to the area where the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. Subcode Area where the density is adjusted Low density area Middle density area High density area © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-61...
Page 116 Therefore, carefully perform the adjustment, while checking the copy image.  Remarks Enter a value within the recommended value range mentioned in the procedures. Otherwise, it may cause a loss in MFP performance, including degradation in the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-62...
Page 117: To Obtain A Good Color Balance On Thick Paper
Then perform other procedures. • Only the service technician must perform procedures (1), (2) and (4). • Both the service technician and the user can perform procedure (3). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-63...
Page 118 Thick paper 4 05-7913 0 to 255 Special paper 1* Special paper 2* Special paper 3 Transparency (OHP film)* * Use the recommended Transparency (OHP film) and special paper 1 and 2. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-64...
Page 119 Closely Match the Color Balance of the Original". After adjusting the tint of colors, copy and check the copy image quality. If further image quality adjustments are still necessary, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-65...
Page 120 Subcode Area where the density is adjusted Low density area Middle density area High density area  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-66...
Page 121 MFP performance, including degradation in the image quality and a reduction in the life of the consumables • If the adjustment causes a toner fixing problem, decrease the values for codes 05-7899 and 7905 to 7911. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-67...
Page 122: To Obtain Smooth Gray-Scale Photo Images
Press [User Functions -User-] and select [Copy] in the [User] tab. Select [Image Smoothing] in the “Original Mode for Black” option.  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-68...
Page 123: To Change The Threshold In Auto Color Mode (To Change The Threshold Between The Full Color Mode And The Black Mode To Meet The User's Needs)
Then it will be copied in the Full color mode or the Black mode. But adjust the threshold value, in order to change the threshold between the Black mode and the Full color mode and suit the preferences of the user. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-69...
Page 124 After specifying the original size and copy size, copy and check the copy image quality. If further image quality adjustments are still necessary, the service technician must perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 125 • Note that arranging the image area to be used for the judgment also adjusts that for the Auto color in network scanning. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-71...
Page 126: To Adjust The Twin-Color Copy Image Quality
The procedure to use varies, depending on whether to adjust the tint of colors other than black, the reproducibility of black in the Red and black mode, or the boundary between black and colors other than black. Refer to the procedure corresponding to the user’s particular request. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-72...
Page 127: To Adjust The Tint Of Colors Other Than Black
• Press [Detail]. The tint of the color can be adjusted according to the density area (low, middle or high density area).  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-73...
Page 128: To Adjust The Boundary Between Black And Colors Other Than Black
Subcode Area where the density is adjusted High density area Middle density area Low density area  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-74...
Page 129: To Adjust The Tint Of Specified Colors For Twin-Color Or Single-Color Copying
Magenta 05-7644 0 to 255 Yellow 05-7645 0 to 255 Yellow green 05-7646 0 to 255 Cyan 05-76405-7 0 to 255 Pink 05-7648 0 to 255 © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-75...
Page 130 (2) After changing the setting value, reboot the equipment, and check the tint of the image printed in twin-color or single-color copying.  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-76...
Page 131: To Adjust The Image Quality Scanned From The Df
• Correctly adjusting the installation heights of the MFP and the DF is a prerequisite to perform this adjustment. Therefore, perform all the necessary adjustments. Only if further adjustment is still desired for the reproducibility of background, should this adjustment be performed. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-77...
Page 132 A darker background is reproduced than the one obtained when the setting value “3” is set. After setting the value, copy and check the image quality. If further image quality adjustment is necessary, go to the next step. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-78...
Page 133 Correctly adjusting the installation heights of the MFP and the DF is a prerequisite to perform this adjustment. Therefore, perform all the necessary adjustments. Only if further adjustment is still desired for the reproducibility of background, should this adjustment be performed. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-79...
Page 134: To Program Frequently Used Copy Settings (To Use Custom Mode)
User Custom mode in the black mode. Value for 08-7034 User Custom mode for black mode Unused Used (Text/Photo base) Used (Text base) After setting the value, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-80...
Page 135 0 to 4 suppressed). When a smaller 2.2.1 text adjustment value is set, they become thicker (smudges in the text will be suppressed). After setting the value, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-81...
Page 136 2.Copier-specific Adjustments (3) In the normal mode, select [User Custom] in Original Mode on the control panel.  Cautions after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-82...
Page 137: To Adjust User Custom Mode Settings In Full Color Mode
• The default adjustment value for the User Custom mode is preset at the one that reproduces the image quality equivalent to that of Text/Photo in the full color mode at the time of shipment. After setting the value, perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-83...
Page 138 The larger the value, the Fine adjustment darker the red becomes. of hue 0 to 255 The smaller the value, the (Magenta) darker the blue becomes. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-84...
Page 139 The larger the value, the Fine adjustment higher the saturation of saturation 0 to 255 becomes. The smaller the (Magenta) value, the lower the saturation becomes. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-85...
Page 140 The larger the value, the Black header darker the header becomes. 05-7816 density level 0 to 8 2.12.1 The smaller the value, the adjustment lighter the header becomes. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-86...
Page 141 After setting the value, perform the next procedure. (3) In the normal mode, select [User Custom] in Original Mode on the control panel.  Cautions after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-87...
Page 142: To Copy While Erasing Shadow Outside Of Image
• In case of special originals (e.g. a three-dimensional object, an original with black edges, the edges of an opened book) © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-88...
Page 143 Also the area to be erased may change depending on the orientation of the original. Therefore adjust it carefully while checking the copy image. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 144: To Avoid Copying Blank Page Of Original Scanned With Df
• You can start with any of the steps. However, it is recommended to perform the steps in order as listed below. • Both the service technician and the user can perform step (1) and (2). • Only the service technician can perform step (3) and (4). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-90...
Page 145 • Note that arranging the image area to be used for the judgment also adjusts that for “Omit Blank Page” in network scanning. • Originals with a small portion of small letters may be judged as a blank page. Therefore adjust the value carefully while checking the copy image. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-91...
Page 146: To Obtain Image In Even Density Level
Perform this function to avoid density unevenness.  Procedures • Both the service technicians and the users can perform step (1). • Only the service technicians can perform step (2). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-92...
Page 147 • Description of the setting value Value Range correction Fixed Flexible After the adjustment is complete, make a copy and confirm the image quality.  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-93...
Page 148: To Improve Reproducibility Of Red Seal Color
(1) Select [08 SETTING MODE]. Change the value for code [7610] to “1”. (2) Press [Basic] tab on the Copy mode. Select “Red Seal Color” among the original modes. After selecting “Red Seal Color”, make a copy and check its image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-94...
Page 149: To Reduce Streaks At Scanning With Df
The procedure of this adjustment differs between “When adjusting the image quality of the Black mode” and “When adjusting the image quality of the Full color mode”. Refer to the procedure corresponding to the user’s particular request. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-95...
Page 150: When Adjusting The Image Quality Of The Black Mode
• When “0” is set for the setting value, this function becomes disabled. After changing the setting value, perform printing and check its image quality.  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-96...
Page 151: When Adjusting The Image Quality Of The Full Color Mode
The noise reduction level is middle. High The noise reduction level is high. After changing the setting value, perform printing and check its image quality.  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-97...
Page 152: The Color Reproduction Of The Back Side Differs From That For The Front Side At Dsdf Scanning
If you want to return the color reproduction of the back side at the DSDF scanning to the original one after the adjustment has been performed with this procedure, carry out the code [7002] in [08 SETTING MODE]. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-98...
Page 153: To Improve The Gradation Reproduction Of Dark Portions In Photos
• Set the value in increments of 1, while checking the copy image until the optimum value is obtained. • For the User Custom mode, refer to "2.19 To Program Frequently Used Copy Settings (To use Custom Mode)". © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-99...
Page 154 This adjustment will affect to that for set at (3) in "2.12.1 To Adjust the Copy Image Quality of a Black Logo". When performing this adjustment, pay attention to the balance against the reproduction level of the black color logos, too. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-100...
Page 155: To Improve The Reproducibility Of Dark-Color Text / To Clearly Make Halftone Dots In Gray With Color Copying
Original mode [05] Code Remarks Text/Photo 7843-0 Text 7843-1 0: Black text priority (default) 7843-2 1: Color text / halftone dots in gray priority User Custom 7843-3 Red Seal Color 7843-4 © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-101...
Page 156 High density Low density M (Magenta) Middle density High density User Custom Low density C (Cyan) Middle density High density Low density K (Black) Middle density High density © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-102...
Page 157: To Make A Copy By Removing All Colors Other Than Black
To Make a Copy by Removing all Colors other than Black Original When the Drop out color function Normal Black mode copying option is enabled Colors other than black are Colors other than black are not reproduced in gray. reproduced. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-103...
Page 158 * “Color originals” include not only the colored mark sheet originals with notes added in black pencil but also monochrome originals with notes added by a color pen. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-104...
Page 159 Therefore, perform the adjustment while checking the copied result. • If a smaller value is set (gray-like colors tend to remain), colors whose removal is desired will also remain. Therefore, perform the adjustment while checking the copied result. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 2-105...
Page 161: Printer-Specific Adjustments
* PD: Printer driver * UF: User Functions menu (control panel) <Notes> • Both the service technician and the user can perform the adjustments on a printer driver and on the control panel. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 162: Gamma Balance Adjustment
Low density Middle density High density • Set the value in increments of around 10, while checking the print image until the optimum value is obtained. • Adjust PS for Mac. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 163 3.Printer-specific Adjustments  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 164: Pureblack/Gray Threshold Value Adjustment
Open the Properties page of the printer driver and then select “Advanced” on the “Image Quality” tab. In the “Basic” tab, mark the “Pure Gray” checkbox and select “Text, Graphic & Image” from among the “Apply to” options. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 165 * This adjustment will have an effect only on full-color printing. Open the print dialog box. Select “Color Settings 1” - “Black & Gray – Text, Graphic & Image” from among the “Pure Black and Gray” options. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 166 When an illustrator is used, select [File] > [Document Setting] > [Custom] and then set to the value to “Vector” in the Rasterization and Vector Balance option.  Caution after the adjustment Nothing in particular e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 167: Background Adjustment
Open the property page of the printer driver and click [Setting] in the “Image Quality” tab. Set the “Background adjustment” option in the “Image Attribute” tab within the range of “1” to “4”. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 168 0 to 255 than 128. Mono 05-8015 color Color 05-8016 Smooth Mono 05-8018 color 1200 dpi Color 05-8017 Detail Mono 05-8019 color Subcode  Caution after the adjustment Nothing in particular e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 169: Sharpness Adjustment
Set the value for “Sharpness” within a range of “- 4” to “4” in the “Image Attribute” tab. • Setting “4” provides the sharpest print image. • Sharpness adjustment is not available when 1200 dpi is selected for PS printer driver. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 170 Open the print dialog box. Set the value for “Color Settings 2” - “Sharpness” within a range of “- 4” to “4”. • Setting “4” provides the sharpest print image. After changing the options on the printer driver, print and check the print image quality. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-10...
Page 171 • If a much too large value is set, small text may be blurred. • If “0” is set, the image quality will not be changed even if the sharpness has been adjusted on the printer driver. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-11...
Page 172 Jaggies on thick lines can be suppressed by applying thin line adjustment to Graphic and increase the sharpness setting level on the printer driver.  Caution after the adjustment Nothing in particular e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-12...
Page 173: Color Balance Adjustment
• “Color Balance” tab: Change the “All Colors” or “Each Color” option • Initially, change the value by 4 steps, while checking the printouts until the optimum value is obtained. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-13...
Page 174 After changing the option on the printer driver, print and check the print image quality. If further image quality adjustments are still necessary, the service technician must perform the next procedure. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-14...
Page 175 05-8165 0/1/2 Text 1200 dpi 05-8166 0/1/2 05-8167 0/1/2 05-8168 0/1/2 05-8169 0/1/2 Auto Graphic 05-8170 0/1/2 05-8171 0/1/2 05-8172 0/1/2 05-8173 0/1/2 Image 05-8174 0/1/2 05-8175 0/1/2 © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-15...
Page 176 • The subcode varies according to the area where the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. Subcode Area where the density is adjusted Low density area Middle density area High density area e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-16...
Page 178: Fine Line / Text Density Adjustment
Adjustment When the upper limit range value is increased, a lower limit line with a darker color Full color Adjustment will become the target range for the adjustment. upper limit e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-18...
Page 179 • When the setting value is increased while a 3D object such as Word Art in Microsoft Office is printed at 1200 dpi, the boundary may become darker.  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-19...
Page 180: Graphic Line Width Adjustment
Enable the “Distinguish Thin Line” option on the printer driver. For Windows Open the property page of the printer driver. Click “Setting” in the “Image Quality” tab. Mark the “Distinguish Thin Line” checkbox in the “Basic” tab. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-20...
Page 181 • The unit of the setting value is the number of dots (line thickness). Lines thinner than the setting value will become thicker as specified. • Set the value while checking the print image until the optimum value is obtained.  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-21...
Page 182: Blurred Text In Black Adjustment
• The “Color” options are available in the “Basic” tab on the PCL, PS and XPS printer drivers. The “Color Type” options are available in the “Color Settings 1” menu in the print dialog box on Mac. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-22...
Page 183 1200 dpi Black 7305  Caution after the adjustment Perform the adjustment while checking the printed images since faint black text or black thin lines may occur. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-23...
Page 184: Toner Used Amount Adjustment
Thick paper 1 Thick paper 2 Thick paper 3* Thick paper 4* Special paper 1 Special paper 2 Special paper 3* Thin paper* Envelope Transparency (OHP film) * e-STUDIO2515AC/3015AC/3515AC/4515AC/5015AC only e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-24...
Page 185  Caution after the adjustment The adjustment may possibly cause dark areas such as shades on photo images to look unnaturally faint. Therefore, carefully perform the adjustment, while checking the printouts. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-25...
Page 186: Halftone Adjustment (When Changing Per User)
You can reduce jaggies by selecting [Detail] in the “Halftone” options. For Windows Open the property page of the printer driver. Click “Setting” in the “Image Quality” tab. Select “Detail” from among the “Halftone” options in the “Basic” tab. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-26...
Page 187 Open the print dialog box. Select “Color Settings 1” - “Detail” from among the “Halftone” options. After changing the option on the printer driver, print and check the print image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 188: Halftone Adjustment (When Changing All Print Jobs)
• This setting applies to print jobs with 600 dpi. Set this to color and black printing, respectively. Changing the setting displays the Confirmation screen that asks whether you want to perform calibration (automatic gamma adjustment) or not. Be sure to select [OK] and carry it out. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-28...
Page 189 (High) Reduces white voids occurred on the text and boundary whose color is the same type of the background. (middle) © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-29...
Page 190  Caution after the adjustment When the low screen ruling is set, jaggedness may appear on diagonal or curved lines. In this case, check the printed image and then switch the setting if necessary e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-30...
Page 191: Pulse Width Adjustment
Decelerating (C) Decelerating (K) • Set the same value for the standard speed and decelerating. • When the value is changed, the images to be copied or faxed will be affected. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-31...
Page 192 Low density area (C) High density area (C) • When the value is changed, the images to be copied or faxed will be affected.  Caution after the adjustment Nothing in particular e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-32...
Page 193: Restrictions On Use Of Printer Functions
     Toner Limit      Calibration    *1 Applicable only to a PS printer driver *2 Applicable only to black (K) © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-33...
Page 194: To Make Print Suitable For The Original
• Auto Color: Automatically judges the type of each color on the originals. Full-color originals are printed in the full color mode and black-and-white originals are printed in the black mode. • Twin Color: Performs printing in black and the specified color. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-34...
Page 195 * This adjustment will have an effect only on Auto or Color mode printing. Open the property page of the printer driver. Change the “Image Quality Type” option in the “Image Quality” tab. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-35...
Page 196 Mac) or if a file created on the above applications is printed. However, the color balance may be changed, and also the image quality may be diminished, depending on the type of file. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-36...
Page 197 (graphs, etc.) 600 dpi: Originals in which priority is to be given to the color or gradation when printing (photographs, design drawings, etc.)  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-37...
Page 198: To Maintain A Steady Color Balance
To Maintain a Steady Color Balance on Plain Paper Before adjustment After adjustment The color balance varies according to a change in the environment or a lapse of The color balance is constantly maintained. time. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-38...
Page 199 (i) Press the [START] button to perform calibration. When the calibration comes to an end, the message “Scanning and calibrating” will disappear.  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-39...
Page 200: To Maintain A Steady Color Balance On Thick Paper Or Special Paper
• Perform the adjustment in accordance with the procedures below. • Only the service technician must perform procedure (1). • Both the service technician and the user can perform procedure (2). e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-40...
Page 201 • When you press [Calibration], a chart is printed out and the calibration guide illustration is displayed on the control panel. Proceed to the next step. (i) Place the paper type (A4/LT size) selected in (g) on the bypass tray. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-41...
Page 202 • If the chart is not properly placed, the message “Set chart correctly” is displayed on the control panel. In this case, return to step (j) and realign the chart.  Caution after the adjustment Nothing in particular e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-42...
Page 203: To Adjust Colors
 Procedures (1) Perform color balance adjustment. For details of the adjustment procedure, refer to "3.1.5 Color Balance Adjustment".  Caution after the adjustment Nothing in particular © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-43...
Page 204: To Closely Match The Color Balance On The Monitor
On commercially available monitors, sRGB is not selected as a color space by default. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-44...
Page 205 * This adjustment will have an effect only on Auto or Color mode printing. Open the property page of the printer driver. Select “Photograph” from among the “Image Quality Type” options. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-45...
Page 206 • In general, it is impossible to reproduce color saturation closely matching the true colors, as viewed on the monitor, because the range of colors reproducible in toner colors is narrower than the one on the monitor. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-46...
Page 207: To Maintain A Uniform Gray Hue (To Maintain Consistency In Gray Among Text, Photos And Graphics)
 Procedures Both the service technician and the user can perform all adjustments. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-47...
Page 208 * This adjustment will have an effect only on Auto or Color mode printing. Open the property page of the printer driver. Press [Setting] in the “Image Quality” tab. Unmark the “Pure Gray” checkbox in the “Basic” tab. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-48...
Page 209 The adjustment allows gray areas always to be reproduced using all color toners (C, M, Y and K). As a result, undesired colors may look blended, depending on the print image. Therefore, carefully perform the adjustment, while checking the printouts. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-49...
Page 210: To Use Only The Black Toner To Reproduce Gray Areas (To Use Only The Black Toner To Reproduce Black-And-White Photos Or Gradational Images)
C, M, Y and K are used as described above.  Procedures (1) Perform PureBlack/Gray threshold value adjustment. For details of the adjustment procedure, refer to "3.1.2 PureBlack/Gray Threshold Value Adjustment".  Caution after the adjustment Nothing in particular e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-50...
Page 211: To Easily Adjust The Overall Brightness
A darker print image is obtained. A brighter print image is obtained.  Explanation The brightness of the print image can be easily adjusted by changing the “Brightness” setting on the printer driver. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-51...
Page 212 • Select the desired value for brightness on a scale of “-4” (Darkest) to “4” (Lightest). For Windows Open the property page of the printer driver. Click [Setting] in the “Image Quality” tab. Change the “Brightness” option in the “Image Attribute” tab. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-52...
Page 213 Open the print dialog box. Change the “Color Settings 2” - “Brightness” option.  Caution after the adjustment Nothing in particular.  Remarks The brightness adjustment does not affect black text (CMY = 100%, K = 100% or RGB = 0%). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-53...
Page 214: To Adjust The Overall Saturation
After adjustment The saturation is decreased. The saturation is increased.  Explanation The saturation of the print image can be easily adjusted by changing the “Saturation” option on the printer driver. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-54...
Page 215 (1) Change the “Saturation” option on the printer driver. For Windows Open the property page of the printer driver. Click “Setting” in the “Image Quality” tab. Change the “Saturation” option in the “Image Attribute” tab. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-55...
Page 216 After changing the option on the printer driver, print and check the print image quality. Only if the saturation of R (Red) is still insufficient even after all the above procedures have been performed, must the service technician perform the next procedure. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-56...
Page 217  Caution after the adjustment Nothing in particular.  Remarks The saturation adjustment does not affect black or gray areas on the printout. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-57...
Page 218: To Easily Adjust The Overall Contrast
The contrast of the print image can be easily adjusted by changing the “Contrast” option on the printer driver.  Procedures Both the service technician and the user can perform all adjustments. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-58...
Page 219 • Select the desired value for contrast on a scale of “- 4” (Lowest) to “4” (Highest). For Windows Open the property page of the printer driver. Click “Setting” in the “Image Quality” tab. Change the “Contrast” option in the “Image Attribute” tab. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-59...
Page 220 * This adjustment will have an effect only on full-color printing. Open the print dialog box. Change the “Color Settings 2” - “Contrast” option.  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-60...
Page 221: To Print Images In Sharp/Soft
Text and lines on the background of a gradational image as well as text in the Format AutoShape dialog box with transparency selected on Microsoft Office may be blurred especially.  Procedures (1) Perform sharpness adjustment. For details of the adjustment procedure, refer to "3.1.4 Sharpness Adjustment". © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-61...
Page 222 3.Printer-specific Adjustments  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-62...
Page 223: To Adjust Text And Lines
Mac) or if a file created on the above applications is printed. However, the color balance may be changed, and also the image quality may be diminished, depending on the type of file. • Color tones may be changed accordingly. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-63...
Page 224 • After the halftone setting has been changed, perform automatic calibration. • When the halftone setting for Graphic is changed, stepped gaps or discoloration tend to occur in areas where colors have gradated smoothly. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-64...
Page 225 3.Printer-specific Adjustments  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-65...
Page 226: To Reduce Jaggies On Text And Lines (Improvement By Means Of Density Adjustment)
A smoother (softer) image is obtained.  Explanation If the colors of text and lines are light ones, conspicuous jaggies can be made difficult to see by changing the color level to become darker. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-66...
Page 227 By increasing the density of lines and text with this adjustment, jaggies can become difficult to see. For details of the adjustment procedure, refer to "3.1.5 Color Balance Adjustment".  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-67...
Page 228: To Adjust The Line Thickness
(4) Perform blurred text in black adjustment. By performing this adjustment, a blurred barcode sometimes becomes readable. For details of the adjustment procedure, refer to "3.1.8 Blurred Text in Black Adjustment". e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-68...
Page 229 By performing this adjustment, the line thickness can be changed. If you want to arrange dark lines, adjust the code to give priority to high density. For details of the adjustment procedure, refer to "3.1.12 Pulse Width Adjustment".  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-69...
Page 230: To Suppress Smudges On Text And Lines
(4) Reduce the toner used amount. By reducing the toner amount used for printing, this symptom will be suppressed. For details of the adjustment procedure, refer to "3.1.9 Toner Used Amount Adjustment". e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-70...
Page 231 3.Printer-specific Adjustments  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-71...
Page 232: To Clearly Print Double Lines And Text
For details of the adjustment procedure, refer to "3.1.12 Pulse Width Adjustment". (2) Perform potential on printing white text / correction setting adjustment. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-72...
Page 234: To Print Illegible Gray Or Colored Text In Black
• This adjustment will have an effect only on printing on a Windows PCL or PS or XPS emulation printer driver. (This adjustment cannot be performed on a Mac printer driver.)  Procedures Both the service technician and the user can perform all adjustments. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-74...
Page 235  Caution after the adjustment Nothing in particular.  Remarks Not all colored text may be printed in black, depending on the type of text (e.g. text larger than 72 points). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-75...
Page 236: To Make The Light-Colored Area Darker On The Printout
To print only the light area in a higher density and leave the dark area as it is, change the setting for the printer driver and adjust the background and color balance. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-76...
Page 237 * This adjustment will have an effect only on Black and white mode printing. (3) Perform gamma balance adjustment. For details of the adjustment procedure, refer to "3.1.1 Gamma Balance Adjustment".  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-77...
Page 238: To Decrease The Image Density And Save Toner
If image density in the toner saving mode needs to be adjusted according to your customer’s request, change its upper limit value.  Procedures Both the service technician and the user can perform all adjustments. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-78...
Page 239 3.Printer-specific Adjustments (1) Enable the “Toner Save” option on the printer driver. For Windows Open the property page of the printer driver. Mark the “Toner Save” checkbox in the “Others” tab. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-79...
Page 240 The print density in the toner save mode can also be adjusted. For further information regarding the adjustment procedures, refer to "3.8.2 To Adjust the Image Density in the Toner Saving Mode". e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-80...
Page 241: To Adjust The Image Density In The Toner Saving Mode
Adjust the upper limit of the image density in the toner saving mode, in order to obtain the desired image density requested by a particular user.  Procedures The service technician must perform all adjustments. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-81...
Page 242 0 to 255 Set a value larger than 176 to increase the density. • Set the value in increments of approximately 10, while checking the printouts until the optimum value is obtained. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-82...
Page 243 The adjustment may possibly cause an increase of the amount of toner used (if the image density is increased) or provide faint print images (if the image density is decreased). Therefore, carefully perform the adjustment, while checking the printouts. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-83...
Page 244: To Ignore Blank Pages For Printing
Change the option on the printer driver, in order to ignore all blank pages for printing.  Procedures Both the service technician and the user can perform all adjustments. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-84...
Page 245 (1) Enable the “Do not Print Blank Pages” option on the printer driver. For Windows Open the property page of the printer driver. Mark the “Do not Print Blank Pages” checkbox in the “Others” tab. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-85...
Page 246 If any data are inserted in the header or footer of a particular page on Excel or Word, even though no data are present in the body, the page will not be recognized as a blank page. The header or footer will be printed out. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-86...
Page 247: To Prevent Dark Toner From Coming Off
This adjustment does not affect a single color of C, M, Y and K, or bright colors such as red and green.  Procedures (1) Perform toner used amount adjustment. For details of the adjustment procedure, refer to "3.1.9 Toner Used Amount Adjustment".  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-87...
Page 248: To Register The Image Quality Adjusted Corresponding To A Preference (To Use The Custom Color Settings)
“General” tab and open [Printing Preferences]. Mark the “Detail” checkbox in the “Color Balance” tab. Click “Edit”. Set the value for the Middle density of the color in the “Color Balance Details” option. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-88...
Page 249 (b) Enter an optional name in the “Name” option. (c) Select the type you would like to use as the base one from among the “Image Quality Type” options in “Original Image Quality Type”. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-89...
Page 250 The checkbox in the “Custom Color Settings” option will be effective, only if you login using a user name belonging to Administrator or Power Users, and open the property page of the printer driver in the "Printers" or "Devices and Printers" folder. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-90...
Page 251: To Print A Full-Color Original In Two Colors
The procedure to use varies depending on whether “To Adjust Colors”, “To Adjust the Sharpness” or “To Print a Full-Color Original in Two Colors”. Refer to the procedure corresponding to the particular user’s request. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-91...
Page 252: To Adjust Colors
Open the property page of the printer driver. Select “Twin Color” from among the “Color” options in the “Basic” tab. Click “Details”. Select the color to be used for the area other than black, from among the “Color” options. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-92...
Page 253 After selecting these options, print and check the print image quality. If color tone adjustment is required for colors to be used in the area other than black, perform procedures (2) and (3) sequentially. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-93...
Page 254 C (Cyan) 05-8032 0/1/2 Red/Green/ Blue/Cyan/ K (Black) 05-8023 0/1/2 Magenta/ Yellow • Set the value in increments of approximately 20, while checking the printouts until the optimum value is obtained. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-94...
Page 255 Yellow  (3) Perform halftone adjustment. For details of the adjustment procedure, refer to "3.1.11 Halftone Adjustment (when changing all print jobs)".  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-95...
Page 256: To Adjust The Sharpness
“Basic” tab. Click “Details”. Select the color to use for the area other than black, from among the “Color” options. (2) Change the “Use Sharpness Filter” option on the printer driver. (3) Perform sharpness adjustment. For details of the adjustment procedure, refer to "3.1.4 Sharpness Adjustment". e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-96...
Page 257 3.Printer-specific Adjustments  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-97...
Page 258: To Print A Full-Color Original In Two Colors
Recommended value Default value range Text 8213 Increase the setting value to Graphic 8214 1 to 255 enlarge the black area. Image 8215  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-98...
Page 259: To Use Icc Profile
Printing with CMYK Inks of Each Ink Manufacturer”, “To Print Using Custom RGB Profiles”, “To Convert Colors with Specified Source ICC Profiles (Not Using Embedded ICC Profiles)” or “To Perform Further Adjustment After Using ICC Profiles”, according to the request from the user. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-99...
Page 260: To Create Icc Profiles For Printing On The Paper To Be Used
Both the service technician and the user can perform all settings. (1) Open the Properties page of the printer driver and then select the paper type on the “Paper Type” option on the “Basic” tab menu. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-100...
Page 261 (3) Select the desired type of halftone on the “Halftone” option on the “Basic” tab menu. • It is not recommended to select “Auto” on this option because several types of halftone may be used on the same page. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-101...
Page 262 (4) Select the desired resolution level on the “Resolution” option. • “1200dpi” is selectable only for PS printer driver. (5) Uncheck “Use Sharpness Filter” on the “Image Attribute” tab menu. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-102...
Page 263 (6) Select “None” on the “CMYK Source Profile” option on the “Advanced” tab menu. • At this step you can set any printer profile. (7) Uncheck “Apply to Device Color Only”. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-103...
Page 264 • Read the precautions provided by the ICC profile creation software carefully before starting printing. • The correct image may not be printed on some paper types that are out of the MFP’s specifications. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-104...
Page 265: To Print Precise Colors Using Existing Rgb Source Icc Profiles
Follow (a) to (g) below to upload the profiles. (a) Access TopAccess and open the “Administration” tab menu. (b) Open the “Setup” menu and the “ICC Profile” submenu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-105...
Page 266 The display returns to the “ICC Profile” submenu. (f) Click “Save”. A confirmation dialog box is displayed. (g) Click “OK”. • For the details of TopAccess, see the TopAccess Guide. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-106...
Page 267 (3) Open the Properties page of the printer driver and then select “Advanced” on the “Image Quality Type” option on the “Image Quality” tab menu. Then click “Setting”. (4) Select the uploaded RGB profile on “RGB Source Profile” on the “Advanced” tab menu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-107...
Page 268 • Not all colors may be printed precisely because the color gamut reproducible with MFPs differs depending on the models. • The accuracy of color reproduction differs depending on printer profiles used. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-108...
Page 269: To Perform Simulated Printing With Cmyk Inks Of Each Ink Manufacturer
Follow (a) to (g) below to upload the profiles. (a) Access TopAccess and open the “Administration” tab menu. (b) Open the “Setup” menu and the “ICC Profile” submenu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-109...
Page 270 The display returns to the “ICC Profile” submenu. (f) Click “Save”. A confirmation dialog box is displayed. (g) Click “OK”. • For the details of TopAccess, see the TopAccess Guide. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-110...
Page 271 (3) Open the Properties page of the printer driver and then select “Advanced” on the “Image Quality Type” option on the “Image Quality” tab menu. Then click “Setting”. (4) Select the uploaded CMYK profile on “CMYK Source Profile” on the “Advanced” tab menu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-111...
Page 272 • Not all colors may be printed precisely because the color gamut reproducible with MFPs differs depending on the models. • The accuracy of color reproduction differs depending on printer profiles used. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-112...
Page 273: To Print Using Custom Rgb Profiles
Follow (a) to (g) below to upload the profile. (a) Access TopAccess and open the “Administration” tab menu. (b) Open the “Setup” menu and the “ICC Profile” sub menu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-113...
Page 274 The display returns to the “ICC Profile” sub menu. (f) Click “Save”. A confirmation dialog box is displayed. (g) Click “OK”. • For the details of TopAccess, see the TopAccess Guide. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-114...
Page 275 (3) Open the Properties page of the printer driver and then select “Advanced” on the “Image Quality Type” option on the “Image Quality” tab menu. Then click “Setting”. (4) Select the uploaded ICC profile on “Custom RGB profile” on the “Advanced” tab menu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-115...
Page 276 3.Printer-specific Adjustments  Caution after the adjustment Nothing in particular  Remarks Not all colors may be printed precisely because the color gamut reproducible with MFPs differs depending on the models. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-116...
Page 277: To Convert Colors With Specified Source Icc Profiles (Not Using Embedded Icc Profiles)
CMYK source profile and printer profile. Follow (a) to (g) below to upload the profiles. (a) Access TopAccess and open the “Administration” tab menu. (b) Open the “Setup” menu and the “ICC Profile” submenu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-117...
Page 278 The display returns to the “ICC Profile” submenu. (f) Click “Save”. A confirmation dialog box is displayed. (g) Click “OK”. • For the details of TopAccess, see the TopAccess Guide. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-118...
Page 279 (3) Open the Properties page of the printer driver and then select “Advanced” on the “Image Quality Type” option on the “Image Quality” tab menu. Then click “Setting”. (4) Select the uploaded profile on “RGB Source Profile” or “CMYK Source Profile” on the “Advanced” tab menu. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-119...
Page 280 3.Printer-specific Adjustments (5) Uncheck “Apply to Device Color Only”. (6) Select the uploaded printer profile on “Profile” of the “Destination Profile” option. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-120...
Page 281 Colors printed in this procedure may not be completely the same as those of Fiery images because the color measurement method of this procedure is not completely equal to the one for Fiery. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 282: To Perform Further Adjustment After Using Icc Profiles
Both the service technician and the user can perform all settings. (1) Open the Properties page of the printer driver and then select “Advanced” on the “Image Quality Type” option on the “Image Quality” tab menu. Then click [Setting]. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-122...
Page 283 (2) Select the desired profiles on “RGB Source Profile”, “CMYK Source Profile” or “Profile” of the “Destination Profile” option. (3) Open the “Color Balance” tab menu and then change each setting items to obtain the desired color balance. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-123...
Page 284 3.Printer-specific Adjustments (4) Open the “Image Attribute” tab menu and then change each setting items to obtain the desired image quality.  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-124...
Page 285: To Improve The Reproducibility Of Red Seal Color
Open the property page of the printer driver. Select “General” in the “Original Image Quality Type” box in the “Image Quality” tab, and then click [Setting]. Mark the “Red Seal Color Mode” checkbox in the “Basic” tab. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-125...
Page 286 Open the print dialog box. Select the “Color Settings 1” - “Red Seal Color Mode” check box. After changing the setting on the printer driver, print the image and check its image quality.  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-126...
Page 287: To Suppress The Unevenness And Jitteriness On Images, White Voids In The Lines On Background And Around Text
(1) Perform halftone adjustment by using 08-7310, 7314, 8110-8112. For details of the adjustment procedure, refer to "3.1.11 Halftone Adjustment (when changing all print jobs)".  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-127...
Page 288: To Suppress Color Misalignment
Perform the adjustment while checking the images, since the outline form of the boundary of the text or graphics will be accentuated if the effectiveness of the trapping is enhanced. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 3-128...
Page 289 3.Printer-specific Adjustments  Remarks • This adjustment will be reflected only when “600dpi” is set in Resolution. • This adjustment is effective only to the boundary of the text or graphics. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 3-129...
Page 291: E-Filing-Specific Adjustments
Auto Color mode. • This adjustment will have an effect on the image stored using Scan to File and Scan to E-mail. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 292 The data will increase in size, compared to those in the binary mode. • The adjustment of density will be effective, only if “Standard” is selected from among the “Image Quality for Black in ACS” options. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 293: To Store An Original While Reducing The File Size
• This adjustment will have an effect on images stored using Scan to File and Scan to E-mail.  Procedures Both the service technician and the user can perform all adjustments. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 294 If the full-color or gray-scale image is copied or printed and stored in the e-Filing box (Copy to Box or Print to Box), the user can select a desired compression rate, when downloading the image using File Downloader on a client PC. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 295: To Match The Color Balance On The Original (To Adjust The Color Balance In Print To Box)
The image stored in the e-Filing box looks The color balance of the image stored is different in the color balance from the closely matched with that of the original. original. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 296 • “General” allows the image to be stored in colors, which are closely matched with the original, compared to the other Image Quality Type options.  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 297: To Scan And Print, While Minimizing Moiré
Auto color mode). After changing the original mode, scan and store the original. Then print and check the print image quality. If further image quality adjustments are still necessary, perform other procedures. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 298 When the original containing text and lines is scanned and printed, the adjustment may possibly cause the blurred text and lines or a blend of undesired colors. Therefore, carefully perform the adjustment, while checking the scanned-in image or printout. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 299: To Finely Print The Image Stored In The E-Filing Box (To Print Images Stored Through Copy To Box Or Print To Box)
If the image is printed out directly from the downloaded to a PC and then printed out, e-Filing box, the image quality will be the image data conversion may diminish maintained. the image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 300 Note that files created through the Archive Document or Backup feature cannot be directly opened on the PC or printed out. For further information regarding Archive Document and Backup, refer to the e-Filing Guide. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 4-10...
Page 301: To Store An Image Suitable For Displaying On The Monitor Or Image Editing
Scan to Box. This can avoid unnecessary since it is optimized for printing on paper. data conversion. As a result, the image This may diminish the image quality. quality can be maintained. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 4-11...
Page 302 (1) Scan the full-color image and store it in the e-Filing box. For further information regarding how to scan and store images, refer to the Operator’s Manual for e-Filing Guide and Scanning Guide.  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 4-12...
Page 303: To Finely Print Color Images Scanned And Stored (To Print Images Stored Through Scan To Box)
When the printing image mode suitable for printing may be performed with image the stored data is selected, the data can be processing not suitable for the stored data. printed finely with optimal image processing. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 4-13...
Page 304 (3) Print out the image stored in the e-Filing box on the Control Panel or using the e-Filing Web utility. For further information regarding how to print it out, refer to the Operator’s Manual for e-Filing Guide. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 4-14...
Page 305 Set a larger value than “128” to enhance the sharpness level. Set a smaller value than “128” to decrease the sharpness level. After changing the setting value, perform printing and check its image quality.  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 4-15...
Page 306: Appendix
Displaying on a Scan to Box to be displayed on a computer monitor. computer monitor To print color images stored with the scanning Scan to Box Printing on paper function more clearly. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 4-16...
Page 307: Scanning-Specific Adjustments
• “Mid” is selected from among the compression rate options by default. After changing the compression rate, scan the original and check the scanned-in image quality. If further image quality adjustments are still necessary, perform procedure (2). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 308 Full color mode (including the Auto Color mode): 600 / 400 / 300 / 200 / 150 / 100 (dpi) Gray scale mode: 600 / 400 / 300 / 200 / 150 / 100 (dpi) Black mode: 600 / 400 / 300 / 200 / 150 / 100 (dpi) e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 309: To Scan An Original, While Eliminating The Background Color (To Eliminate The Background Density)
After decreasing the background density, scan the original and check the scanned-in image quality. With the background density set to the minimum, if further image quality adjustments are still necessary, the service technician must perform the next procedure. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 310 (c) Press [Next] twice to display the menu to change the initial values for the Full color and Auto color modes. (d) Select the default background density in the “Background Adjustment” option. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 311: To Clearly Scan And Print An Original In Black And White (To Improve Gradation And Reduce Graininess)
7 times in the Gray scale mode. If the file size in the Black mode with the Photo mode selected is 1, it will be approximately doubled in the Gray scale mode. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 312: To Scan The Original, While Reducing The File Size
Scanning the Original” in order to reduce the file size without changing the file format. Refer to “To Reduce the File Size in Slim PDF” in order to give a higher priority to the file size reduction than the image quality. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 313: To Reduce The File Size By Changing The Options When Scanning The Original
Auto Color mode) or the Gray scale mode. After changing the compression rate, scan the original and check the scanned-in image quality. If further image quality adjustments are still necessary, perform other procedures. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 314 Text Approx. 20% • Correlation between the compression rate and the file size (procedure (3)) The file size is 100%, with [Mid] selected. Compression rate File size ratio 100% Approx. 60% e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved...
Page 315 • Remember that when scanning the original in the Full color mode, if the original mode option is switched from the “Text/Photo” mode or the “Photo” to the “Text” mode, the file size may become larger. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC...
Page 316: To Reduce The File Size In Slim Pdf
After changing the “Rotation” option, scan the original and check the scanned-in image quality. If further image quality adjustments are still necessary, the service technician must perform the next procedure. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-10...
Page 317  Caution after the adjustment The adjustment may possibly cause blurred text, noise or vary the hues of areas. Therefore, carefully perform the adjustment, while checking the scanned-in image quality. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-11...
Page 318: To Sharply Scan The Original (To Increase The Sharpness Intensity)
Adjust the sharpness intensity, in order to sharply scan the soft and blurred original. • This adjustment will have an effect on the image scanned in all color modes (Full color, Gray scale, Black and Auto color). e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-12...
Page 319 The adjustment may possibly cause moiré. In addition, when text and thin lines in a light-colored background are scanned, the background around the text or line may be eliminated. Therefore, carefully perform the adjustment, while checking the scanned-in image. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-13...
Page 320: To Scan An Original, While Enhancing Black
• This adjustment will have an effect only on the image scanned in the Full color mode (including the Auto Color mode). e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-14...
Page 321 • Setting “0” provides the lightest black, while setting “4” the darkest.  Caution after the adjustment The adjustment may possibly provide the extremely dark background. Therefore, carefully perform the adjustment, while checking the scanned-in image. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-15...
Page 322: To Scan An Original With The Desired Gradation
• This adjustment will have an effect only on the image scanned in the Black mode or the Gray scale mode. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-16...
Page 323 • Gradation in the Black mode will vary, if the middle density area is mainly adjusted. But remember that adjusting the low or high density area will rarely affect the gradation in the Black mode.  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-17...
Page 324: To Register The Original Mode Optimal For A Particular Type Of Original (To Have "Custom" Selected)
Text Photo For the Full color mode Value for 08-8303 Reference original mode Reserved (Default) Text/Photo Text Photo e-document After selecting the reference original mode option, perform the next procedure. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-18...
Page 325 Gamma balance adjustment (High density) The larger the value, the darker the background Full Background 05-8370 0 to 255 becomes. The smaller color adjustment the value, the lighter the background becomes. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-19...
Page 326 (set with 08-8300) becomes smaller. When a larger value is set, the contrast Contrast becomes higher. When 05-8422 0 to 255 adjustment a smaller value is set, it becomes lower. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-20...
Page 327 After adjusting the value in the Custom mode, perform the next procedure. (3) When scanning the original, press [SCAN SETTING] on the Control Panel. Select “User Custom” from among the original mode options.  Caution after the adjustment Nothing in particular. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-21...
Page 328: To Eliminate Shading Around Scanned Images
• When the value is increased, the white void amount all around the scanned image is made wider by the setting value range.  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-22...
Page 329: To Scan Yellow Clearly
(a) Set G (green) to [+] side in Color Balance. (b) Set R (red) to [-] side in Color Balance. (c) Set the color balance with a combination of both (a) and (b). © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-23...
Page 330 • This adjustment influences not only yellow but also other colors. After adjusting the color balance, copy and check the copy image quality.  Caution after the adjustment Nothing in particular. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-24...
Page 331: To Reduce Streaks In Scanning With Df
Setting value Description None The noise reduction function is disabled. (Default) The noise reduction level is low. Middle The noise reduction level is middle. High The noise reduction level is high. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-25...
Page 332 After changing the setting value, perform scanning and check its image quality.  Caution after the adjustment Perform the adjustment while checking the scanned images since the adjustment may decrease the reproducibility of fine characters and lines. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-26...
Page 333: To Change Judgment Area Of [Omit Blank Page] And [Auto Color] (To Make Judgment Properly For Originals Whose Images Are Only Located Near The Edges)
To Change Judgment Area of [Omit Blank Page] and [Auto Color] (To make judgment properly for originals whose images are only located near the edges) Original sample Before adjustment After adjustment © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-27...
Page 334 If a much too small value is set, a misjudgment may be caused by the scanning edge shadows of the originals. Therefore, perform the adjustment while checking the judgment result of each function. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-28...
Page 335: To Make A Scan By Removing All Colors Other Than Black
To Make a Scan by Removing all Colors other than Black Original When the Drop out color function Normal Black mode scanning option is enabled Colors other than black are Colors other than black are not reproduced in gray. reproduced. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-29...
Page 336 * “Color originals” include not only the colored mark sheet originals with notes added in black pencil but also monochrome originals with notes added by a color pen. e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC © 2018 TOSHIBA TEC CORPORATION All rights reserved 5-30...
Page 337 • A change by 10 in the setting value corresponds to 1 step of the slide bar in the touch panel.  Caution after the adjustment Black will be removed accidentally or colors whose removal was desired will remain. Therefore, perform the adjustment while checking the scanned results. © 2018 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2010AC/2510AC/2515AC/3015AC/3515AC/4515AC/5015AC 5-31...

This manual is also suitable for:

E-studio2510ac E-studio2515ac E-studio3015ac E-studio3515ac E-studio4515ac E-studio5015ac

Toshiba e-STUDIO2010AC Imaging Manual

1 General Adjustments - Copying, Printing and E-Filing (Output from Box)

2 Copier-Specific Adjustments

3 Printer-Specific Adjustments

4 E-Filing-Specific Adjustments

Appendix

5 Scanning-Specific Adjustments

Quick Links

Related Manuals for Toshiba e-STUDIO2010AC

Summary of Contents for Toshiba e-STUDIO2010AC

This manual is also suitable for:

Table of Contents