Kramer AFM-20DSP User Manual page 77

Function Description
X-MIC-TYPE Set microphone type.
This is an
Extended Protocol
3000 command.
X-MIC-TYPE? Get microphone type.
This is an
Extended Protocol
3000 command.
X-MIX-LVL Set DSP matrix cross-
point MIX level in dB.
This is an
Extended Protocol
3000 command.
X-MIX-LVL?
Get DSP matrix cross-
point MIX level in dB.
This is an
Extended Protocol
3000 command.
X-MIX-MUTE
Set DSP matrix cross-
point mute state.
This is an
Extended Protocol
3000 command.
AFM-20DSP – Protocol 3000
Syntax
COMMAND
#X-MIC-TYPE<direction_type>.<port_type>.<port_index>,mi
c_type<CR>
FEEDBACK
~nn@X-MIC-TYPE<direction_type>.<port_type>.<port_index>
.<signal_type>.<index>,mic_type<CR><LF>
COMMAND
#X-MIC-TYPE?<direction_type>.<port_type>.<port_index><C
R>
FEEDBACK
~nn@X-MIC-TYPE<direction_type>.<port_type>.<port_index>
.<signal_type>.<index>,mic_type<CR><LF>
COMMAND
#X-MIX-LVLOUT.<port_type>.<port_index>.<signal_type>.<i
ndex>,IN.<port_type>.<port_index>.<signal_type>.<index>
,dB<CR>
FEEDBACK
~nn@X-MIX-LVLOUT.<port_type>.<port_index>.<signal_type>
.<index>,IN.<port_type>.<port_index>.<signal_type>.<ind
ex>,dB<CR><LF>
COMMAND
#X-MIX-LVL?OUT.<port_type>.<port_index>.<signal_type>.<
index>,IN.<port_type>.<port_index>.<signal_type>.<index
<CR>
FEEDBACK
~nn@X-MIX-LVLOUT.<port_type>.<port_index>.<signal_type>
.<index>,IN.<port_type>.<port_index>.<signal_type>.<ind
ex>,dB<CR><LF>
COMMAND
#X-MIX-MUTEOUT.<port_type>.<port_index>.<signal_type>.<
index>,IN.<port_type>.<port_index>.<signal_type>.<index
>,dB<CR>
FEEDBACK
~nn@X-MIX-MUTEOUT.<port_type>.<port_index>.<signal_type
>.<index>,IN.<port_type>.<port_index>.<signal_type>.<in
dex>,<mute_state><CR><LF>
Kramer Electronics Ltd.
Parameters/Attributes Example
The following attributes comprise the
port ID:
▪ –
<direction_type>
o IN
▪ <port_type> –
o MIC
▪ – The port number
<port_index>
as printed on the front or rear
panel and according to IO Config.
1 (Mic 1) to 16 (Mic 16)
– Dynamic/Condenser (not
mic_type
case sensitive)
The following attributes comprise the
port ID:
▪ –
<direction_type>
o IN
▪ <port_type> –
o MIC
▪ – The port number
<port_index>
as printed on the front or rear
panel and according to IO Config.
1 (Mic 1) to 16 (Mic 16)
– Dynamic/Condenser (not
mic_type
case sensitive)
The following attributes comprise the
primary signal ID (suffix 1) and follower
signal ID (suffix 2 or greater):
▪ – IN
<direction_type>
o IN
o OUT
▪ –
<port_type>
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o DANTE
o SPDIF
o MIC
▪ – The port number
<port_index>
as printed on the front or rear
panel
▪ –
<signal_type>
o AUDIO
▪ <index> – Indicates a specific
channel number when there are
multiple channels of the same type
The following attributes comprise the
primary signal ID (suffix 1) and follower
signal ID (suffix 2 or greater):
▪ – IN
<direction_type>
o IN
o OUT
▪ –
<port_type>
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o DANTE
o SPDIF
o MIC
▪ – The port number
<port_index>
as printed on the front or rear
panel
▪ –
<signal_type>
o AUDIO
▪ <index> – Indicates a specific
channel number when there are
multiple channels of the same type
The following attributes comprise the
primary signal ID (suffix 1) and follower
signal ID (suffix 2 or greater):
▪ – IN
<direction_type>
o IN
o OUT
–
▪ <port_type>
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o DANTE
o SPDIF
o MIC
▪ – The port number
<port_index>
as printed on the front or rear
panel
▪ –
<signal_type>
o AUDIO
▪ <index> – Indicates a specific
channel number when there are
multiple channels of the same type
▪ –
<mute_state>
o
ON
o
OFF
Set MIC 3 type to condenser:
#X-MIC-TYPEIN.MIC.3,co
ndenser<CR>
Get MIC 3 type:
#X-MIC-TYPE?IN.MIC.3
<CR>
Set analog audio 13 and Dante
1 cross-point level to -25.2dB:
#X-MIX-LVLOUT.ANALOG_A
UDIO.13.AUDIO.1,IN.DANT
E.1.AUDIO.1,-25.2<CR>
Get analog audio 13 and Dante
1 cross-point level:
#X-MIX-LVL?OUT.ANALOG_
AUDIO.13.AUDIO.1,IN.DAN
TE.1.AUDIO.1<CR>
Mute analog audio 13 and
Dante 1 cross-point:
#X-MIX-MUTEOUT.ANALOG_
AUDIO.13.AUDIO.1,IN.DAN
TE.1.AUDIO.1,ON<CR>
75