Kramer AFM-20DSP User Manual page 69

Function Description
DSP-ACTION? Get DSP parameter.
DSP-METER-
Register DSP meters.
REGISTER
DSP-METER- Unregister DSP
UNREGISTER meters.
EDID-AUDIO Set audio capabilities
for EDID.
EDID-AUDIO? Get audio capabilities
for EDID.
EDID-CS
Set EDID color space.
Set command
might change the
current EDID.
EDID-CS?
Get EDID color space.
Get command
might change the
current EDID.
ETH-PORT Set Ethernet port
protocol.
If the port number
you enter is already in
use, an error is
returned.
The port number must
be within the following
range: 0-(2^16-1).
ETH-PORT?
Get Ethernet port
protocol.
FACTORY Reset device to factory
default configuration.
This command
deletes all user data
from the device. The
deletion can take some
time.
Your device may
require powering off
and powering on for
the changes to take
effect.
FEATURE-LIST? Get feature state
according to the
feature ID.
HDCP-STAT?
Get HDCP signal
status.
Output stage (1) –
get the HDCP signal
status of the sink
device connected to
the specified output.
Input stage (0) – get
the HDCP signal
status of the source
device connected to
the specified input.
HELP
Get command list or
help for specific
command.
AFM-20DSP – Protocol 3000
Syntax
Internal – for web only.
Internal – for web only.
Internal – for web only.
COMMAND
#EDID-AUDIOinput_id,audio_format<CR>
FEEDBACK
~nn@EDID-AUDIOinput_id,audio_format
COMMAND
#EDID-AUDIO?input_id<CR>
FEEDBACK
~nn@EDID-AUDIOinput_id,audio_format<CR><LF>
COMMAND
#EDID-CS input_id,ColSpace<CR>
FEEDBACK
~nn@EDID-CS input_id,ColSpace<CR><LF>
COMMAND
#EDID-CS?input_id<CR>
FEEDBACK
~nn@EDID-CSinput_id,ColSpace<CR><LF>
COMMAND
#ETH-PORTportType,ETHPort<CR>
FEEDBACK
~nn@ETH-PORTportType,ETHPort<CR><LF>
COMMAND
#ETH-PORT?portType<CR>
FEEDBACK
~nn@ETH-PORTportType,ETHPort<CR><LF>
COMMAND
#FACTORY<CR>
FEEDBACK
~nn@FACTORYOK<CR><LF>
COMMAND
#FEATURE-LIST?feature_id<CR>
FEEDBACK
~nn@FEATURE-LISTfeature_id,ir_state<CR><LF>
COMMAND
#HDCP-STAT?stage,stage_id<CR>
FEEDBACK
~nn@HDCP-STATstage,stage_id,status<CR><LF>
COMMAND
#HELP<CR>
#HELPcommand_name<CR>
FEEDBACK
1. Multi-line:
~nn@Devicecommand,command...<CR><LF>
To get help for command use: HELP (COMMAND_NAME)<CR><LF>
~nn@HELPcommand:<CR><LF>
description<CR><LF>
USAGE:usage<CR><LF>
Parameters/Attributes Example
input_id
Audio_format
EDID:
0 – Auto
<CR><LF>
1 – LPCM 2CH
2 – LPCM 6CH
3 – LPCM 8CH
4 – Bitstream
5 – HD
input_id
Audio_format
EDID:
0 – Auto
1 – LPCM 2CH
2 – LPCM 6CH
3 – LPCM 8CH
4 – Bitstream
5 – HD
input_id
ColSpace
0– RGB
4 – auto
input_id
ColSpace
0– RGB
4 – auto
portType
– TCP/UDP port number
ETHPort
(0 – 65535)
portType
0 – TCP
1 – UDP
– TCP / UDP port number (0
ETHPort
– 65535)
Feature_Id
1 – Maestro
2 – Room Controller
Ir_State
0 – Disabled
1 – Enabled
– Input/Output
stage
0 – Input
1 – Output
stage_id
for the input stage
1 – HDMI IN
For the output stage
1 – HDMI OUT
– Signal encryption status -
status
valid values On/Off
0 – HDCP Off
1 – HDCP On
– Name of a specific
command
command
Kramer Electronics Ltd.
– 1
Set HDMI IN audio capabilities
– Audio block added to
for EDID (LPCM 6CH):
#EDID-AUDIO1,2<CR>
– 1
Get HDMI IN 1 audio
– Audio block added to
capabilities for EDID:
#EDID-AUDIO?1<CR>
– 1
Set HDMI IN 1 EDID color
– Color space
space to RGB (enabled):
#EDID-CS1,0<CR>
– 1
Get EDID color space:
– Color space
#EDID-CS?1<CR>
– TCP/UDP
Set the Ethernet port protocol
for TCP to port 12457:
#ETH-PORT0,12457<CR>
– TCP/UDP
Get the Ethernet port protocol
for UDP:
#ETH-PORT?1<CR>
Reset the device to factory
default configuration:
#FACTORY<CR>
– Feature ID
Get the room controller feature
state (for the room controller 1):
#FEATURE-LIST?1<CR>
– IR Interface
Get the output HDCP-STATUS
of HDMI IN:
#HDCP-STAT?0,1<CR>
– Number of chosen stage
Get the command list:
#HELP<CR>
To get help for
AV-SW-TIMEOUT:
HELPAV-SW-TIMEOUT<CR>
67