Kramer AFM-20DSP User Manual page 78

Function Description
X-MIX-MUTE? Get DSP matrix cross-
point mute state.
This is an
Extended Protocol
3000 command.
X-MUTE
Set the mute state of
the signal.
This is an
Extended Protocol
3000 command.
X-MUTE? Get the mute state of
the signal.
This is an
Extended Protocol
3000 command.
AFM-20DSP – Protocol 3000
Syntax
COMMAND
#X-MIX-MUTE?OUT.<port_type>.<port_index>.<signal_type>.
<index>,IN.<port_type>.<port_index>.<signal_type>.<inde
x><CR>
FEEDBACK
~nn@X-MIX-MUTEOUT.<port_type>.<port_index>.<signal_type
>.<index>,IN.<port_type>.<port_index>.<signal_type>.<in
dex>,<mute_state><CR><LF>
COMMAND
#X-MUTE<direction_type>.<port_type>.<port_index>.<signa
l_type>.<index>,state<CR>
FEEDBACK
~nn@X-MIC-TYPE<direction_type>.<port_type>.<port_index>
.<signal_type>.<index>,state<CR><LF>
COMMAND
#X-MUTE?<direction_type>.<port_type>.<port_index>.<sign
al_type>.<index><CR>
FEEDBACK
~nn@X-MUTE<direction_type>.<port_type>.<port_index>.<si
gnal_type>.<index>,state<CR><LF>
Kramer Electronics Ltd.
Parameters/Attributes Example
The following attributes comprise the
primary signal ID (suffix 1) and follower
signal ID (suffix 2 or greater):
▪ – IN
<direction_type>
o IN
o OUT
▪ –
<port_type>
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o DANTE
o SPDIF
o MIC
▪ – The port number
<port_index>
as printed on the front or rear
panel
▪ –
<signal_type>
o AUDIO
▪ <index> – Indicates a specific
channel number when there are
multiple channels of the same type
▪ <mute_state> –
o
ON
o
OFF
The following attributes comprise the
signal ID:
▪ –
<direction_type>
o IN
o OUT
▪ –
<port_type>
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o SPDIF
o DANTE
o MIC
▪ <port_index> – The port number
as printed on the front or rear
panel
–
▪ <signal_type>
o VIDEO
o AUDIO
▪ – Indicates a specific
<index>
channel number when there are
multiple channels of the same type
– OFF/ON (not case sensitive)
state
The following attributes comprise the
signal ID:
▪ –
<direction_type>
o IN
o OUT
▪ –
<port_type>
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o SPDIF
o DANTE
o MIC
▪ <port_index> – The port number
as printed on the front or rear
panel
–
▪ <signal_type>
o VIDEO
o AUDIO
▪ <index> – Indicates a specific
channel number when there are
multiple channels of the same type
– OFF/ON (not case sensitive)
state
Get analog audio 13 and Dante
1 cross-point mute state:
#X-MIX-MUTEOUT.ANALOG_
AUDIO.13.AUDIO.1,IN.DAN
TE.1.AUDIO.1,ON<CR>
Set the mute state of Mic 2
input to off:
#X-MUTEIN.MIC.2.AUDIO.
1,OFF<CR>
Get the mute state of Mic 3
input to off:
#X-MUTE?IN.MIC.3.AUDIO
.1<CR>
76