Kramer AFM-20DSP User Manual page 73

Function Description
PASS Set password for login
level.
The default
password is an empty
string.
PASS? Get password for login
level.
The default
password is an empty
string.
PORTS-LIST? Get the port list of this
machine.
The response is
returned in one line
and terminated with
<CR><LF>.
The response format
lists port IDs separated
by commas.
This is an Extended
Protocol 3000
command.
PROT-VER?
Get device protocol
version.
RESET Reset device.
To avoid locking
the port due to a USB
bug in Windows,
disconnect USB
connections
immediately after
running this command.
If the port was locked,
disconnect and
reconnect the cable to
reopen the port.
SECUR
Start/stop security.
The permission
system works only if
security is enabled
with the "SECUR"
command.
SECUR?
Get current security
state.
The permission
system works only if
security is enabled
with the "SECUR"
command.
SIGNAL? Get input signal status.
SIGNALS-LIST?
Get signal ID list of this
machine.
The response is
returned in one line
and terminated with
<CR><LF>.
The response format
lists signal IDs
separated by commas.
This is an Extended
Protocol 3000
command.
SN?
Get device serial
number.
AFM-20DSP – Protocol 3000
Syntax
COMMAND
#PASSlogin_level,password<CR>
FEEDBACK
~nn@PASSlogin_level,password<CR><LF>
COMMAND
#PASS?login_level<CR>
FEEDBACK
~nn@PASSlogin_level,password<CR><LF>
COMMAND
#PORTS-LIST?<CR>
FEEDBACK
~nn@PORTS-LIST[<direction_type>.<port_type>.<port_index
>,..,]<CR><LF>
COMMAND
#PROT-VER?<CR>
FEEDBACK
~nn@PROT-VER3000:version<CR><LF>
COMMAND
#RESET<CR>
FEEDBACK
~nn@RESETOK<CR><LF>
COMMAND
#SECURsecurity_mode<CR>
FEEDBACK
~nn@SECURsecurity_mode<CR><LF>
COMMAND
#SECUR?<CR>
FEEDBACK
~nn@SECURsecurity_mode<CR><LF>
COMMAND
#SIGNAL?inp_id<CR>
FEEDBACK
~nn@SIGNALinp_id,status<CR><LF>
COMMAND
#SIGNALS-LIST?<CR><LF>
FEEDBACK
~nn@SIGNALS-LIST[<direction_type>.<port_type>.<port_ind
ex>.<signal_type>.<index>,..,]<CR><LF>
COMMAND
#SN?<CR>
FEEDBACK
~nn@SNserial_number<CR><LF>
Kramer Electronics Ltd.
Parameters/Attributes Example
– Level of login to set
login_level
(End User or Administrator).
– Password for the
password
login_level. Up to 15 printable ASCII
chars
– Level of login to set
login_level
(End User or Administrator).
– Password for the
password
login_level. Up to 15 printable ASCII
chars
The following attributes comprise the
port ID:
▪ –
<direction_type>
o IN
o OUT
▪ –
<port_type>
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o SPDIF
o MIC
o DANTE
▪ <port_index> – The port number
as printed on the front or rear
panel
version – XX.XX where X is a decimal
digit
–
security_mode
0 – OFF (disables security)
1 – ON (enables security)
security_mode –
0 – OFF (disables security)
1 – ON (enables security)
inp_id – Input number
1 – HDMI
– Signal status according to
status
signal validation:
0 – Off
1 – On
The following attributes comprise the
signal ID:
▪ <direction_type> –
o IN
o OUT
▪ <port_type> –
o HDMI
o ANALOG_AUDIO
o AMPLIFIED_AUDIO
o SPDIF
o MIC
o DANTE
– The port number
▪ <port_index>
as printed on the front or rear
panel
▪ –
<signal_type>
o AUDIO
o VIDEO
▪ <index> – Indicates a specific
channel number when there are
multiple channels of the same type
– 14 decimal digits,
serial_number
factory assigned
Set the password for the Admin
protocol permission level to
33333:
#PASSAdmin,33333<CR>
Get the password for the
Admin protocol permission
level:
#PASS?Admin<CR>
Get the ports list:
#PORTS-LIST?<CR>
Get the device protocol
version:
#PROT-VER?<CR>
Reset the device:
#RESET<CR>
Enable the permission system:
#SECUR0<CR>
Get current security state:
#SECUR?<CR>
Get the input signal lock status
of IN 1:
#SIGNAL?1<CR>
Get signal ID list:
#SIGNALS-LIST?<CR>
Get the device serial number:
#SN?<CR>
71