Mitsubishi FX3U Series Programming Manual page 9

FX /FX Series Programmable Controllers
3U 3UC
Programming Manual - Basic & Applied Instructions Edition
11. Rotation and Shift Operation - FNC 30 to FNC 39
11.1 FNC 30 - ROR / Rotation Right ................................................................................................ 269
11.2 FNC 31 - ROL / Rotation Left ................................................................................................... 271
11.3 FNC 32 - RCR / Rotation Right with Carry ............................................................................... 273
11.4 FNC 33 - RCL / Rotation Left with Carry .................................................................................. 275
11.5 FNC 34 - SFTR / Bit Shift Right................................................................................................ 277
11.6 FNC 35 - SFTL / Bit Shift Left................................................................................................... 279
11.6.1 Replacement of SFT instruction in F
11.7 FNC 36 - WSFR / Word Shift Right .......................................................................................... 283
11.8 FNC 37 - WSFL / Word Shift Left ............................................................................................. 285
11.9 FNC 38 - SFWR / Shift Write [FIFO/LIFO Control]................................................................... 287
11.10 FNC 39 - SFRD / Shift Read [FIFO Control] .......................................................................... 290
12. Data Operation - FNC 40 to FNC 49
12.1 FNC 40 - ZRST / Zone Reset................................................................................................... 293
12.2 FNC 41 - DECO / Decode ........................................................................................................ 296
12.3 FNC 42 - ENCO / Encode ........................................................................................................ 299
12.4 FNC 43 - SUM / Sum of Active Bits.......................................................................................... 301
12.5 FNC 44 - BON / Check Specified Bit Status............................................................................. 304
12.6 FNC 45 - MEAN / Mean ........................................................................................................... 306
12.7 FNC 46 - ANS / Timed Annunciator Set................................................................................... 308
12.8 FNC 47 - ANR / Annunciator Reset.......................................................................................... 310
12.9 FNC 48 - SQR / Square Root................................................................................................... 311
12.10 FNC 49 - FLT / Conversion to Floating Point ......................................................................... 313
13. High Speed Processing - FNC 50 to FNC 59
13.1 FNC 50 - REF / Refresh ........................................................................................................... 316
13.1.1 What should be understood before using REF instruction ........................................................ 319
13.2 FNC 51 - REFF / Refresh and Filter Adjust.............................................................................. 320
13.2.1 What should be understood before using REFF instruction ...................................................... 322
13.3 FNC 52 - MTR / Input Matrix .................................................................................................... 323
13.3.1 The method and cautions for MTR instruction........................................................................... 326
13.4 FNC 53 - HSCS / High Speed Counter Set.............................................................................. 327
13.4.1 Common cautions on using instructions for high speed counter ............................................... 329
13.5 FNC 54 - HSCR / High Speed Counter Reset.......................................................................... 332
13.6 FNC 55 - HSZ / High Speed Counter Zone Compare .............................................................. 335
13.6.1 Program in which comparison result is set to ON when power is turned ON
[ZCP (FNC 11) instruction] ..................................................................................................... 338
13.6.2 Table high speed comparison mode (M8130) ........................................................................... 340
13.6.3 Frequency control mode (HSZ and PLSY instructions) (M8132) .............................................. 343
13.7 FNC 56 - SPD / Speed Detection............................................................................................. 346
13.8 FNC 57 - PLSY / Pulse Y Output ............................................................................................. 350
13.9 FNC 58 - PWM / Pulse Width Modulation ................................................................................ 355
13.10 FNC 59 - PLSR / Acceleration/Deceleration Setup ................................................................ 358
and F Series ................................................................ 282
1 2
Table of Contents
268
292
315
7