Mitsubishi FX3U Series Programming Manual page 810

FX /FX Series Programmable Controllers
3U 3UC
Programming Manual - Basic & Applied Instruction Edition
Number and name
Pulse Catch (Refer to Section 35.7 for details.)
*1
Input X000 pulse catch
M 8170
*1
Input X001 pulse catch
M 8171
*1
Input X002 pulse catch
M 8172
*1
Input X003 pulse catch
M 8173
*1
Input X004 pulse catch
M 8174
*1
Input X005 pulse catch
M 8175
*1
Input X006 pulse catch
M 8176
*1
Input X007 pulse catch
M 8177
*1. Cleared when PLC switches from STOP to RUN.
FX , FX
2N
FX , FX
1S
Communication Port Channel Setting (Refer to Data Communication Edition for details.)
M 8178 Parallel link channel switch (OFF: ch1/ON: ch2)
M 8179
N:N network channel switch
*2. The channel is specified by either creating or not creating M8179 in setting program.
• ch1: not creating M8179 in setting program
• ch2: creating M8179 in setting program
N:N Network (Refer to FX Series User's Manual - Data Communication Edition for details.)
[M]8180
[M]8181 Not used
[M]8182
*3
Data communication error (Master station)
[M]8183
*3
Data communication error (Slave station No.1)
[M]8184
*3
Data communication error (Slave station No.2)
[M]8185
*3
Data communication error (Slave station No.3)
[M]8186
*3
Data communication error (Slave station No.4)
[M]8187
*3
Data communication error (Slave station No.5)
[M]8188
*3
Data communication error (Slave station No.6)
[M]8189
*3
Data communication error (Slave station No.7)
[M]8190
*3
Data communication in execution
[M]8191
[M]8192
[M]8193
[M]8194
Not used
[M]8195
[M]8196
[M]8197
*3. In FX
1S
*4. Available in Ver. 2.00 or later.
High Speed Counter Edge Count Specification (Refer to Subsection 4.7.8 for details.)
*5*6
C251, C252, C254: 1/4 edge count selector
M 8198
*5*6
C253, C255, or C253 (OP): 1/4 edge count selector
M 8199
*5. OFF: 1 edge count
ON: 4 edge count
*6. Cleared when PLC switches from RUN to STOP.
808
Operation and function
, FX or FX Series PLC: EI (FNC 04) instruction is necessary.
2NC 3U, 3UC
, or FX Series PLC: EI (FNC 04) instruction is unnecessary.
1N 1NC
*2
PLCs, use numbers shown inside parentheses.
36 Operation of Special Devices (M8000 -, D8000 -)
FX FX
3U 3UC
→ For setting program, Refer to Data Communication Edition
– –
– –
– –
– –
– –
– –
– –
– –
– –
36.1 Special Device List (M8000 -, D8000 -)
Applicable model
Correspond-
ing special FX FX FX
1S 1N
device
–
–
–
–
–
–
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
(M504)
(M505)
(M506)
(M507)
D8201 to
(M508)
D8218
(M509)
(M510)
(M511)
(M503)
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
FX FX
2N 1NC 2NC
– –
– –
– –
– –
– –
– –
– –
*4
*4
*4
*4
*4
*4
*4
*4
*4
– –
– –
– –
– –
– –
– –
– –
– –