Aerotech DR500 Operation & Technical Manual page 90

DR500 Operation and Technical Manual
+12V Input Pinout, 3-6, 3-7
5 Volt Logic Inputs, 3-8
50 Conductor Ribbon Cable, 2-33
AC Brushless Drive
Linear Three Phase, 2-8
AC Brushless Drive, 2-8
AC Brushless Drive Configuration, 2-24
AC Brushless Linear Drive Configuration, 2-26
AC Brushless Motor, 2-31, 2-33, 3-8
AC Brushless Motor Connector, 3-15
AC Brushless Motor Connector Pinouts, 3-15
AC Brushless Motor Drive, 2-10
AC Input Voltage, 2-27
AC Line Input Chart, 3-19
AM Series Drive Modules, 2-10
Amplifier problems, 5-1
Amplifier Sync, 3-3
Analog Input
MFO, 3-9
Spare, 3-9
Analog Input 0, 3-9
Analog Inputs, 3-9
Joystick Interface, 3-9
Spare Input, 3-9
AS Series Drive Modules, 2-10
AS3005, 2-8, 2-24
Assure a Properly Connected System, 3-3
Axis 1 Pinouts, 3-5
Axis 1 to 4 Motor Connectors, 2-31
Axis 1-4 Pinouts, 3-10
Axis 2 Pinouts, 3-5
Axis 3 Pinouts, 3-5
Axis 4 Pinouts, 3-5
Axis Enable 4 Output, 3-8
Axis Fault 1 Input, 3-8
Axis Fault 4 Input, 3-8
Boards
CPU Board, 2-33
Interface Board, 2-30
Motherboard, 2-10
Brake Connector Pinouts, 3-12
Brake Mating Connector, 3-12
Brake Output, 3-9
breakout, 1-1
Brush Drive Configuration, 2-11
Version 1.6
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
INDEX
Symbols
A
B
Aerotech, Inc.
Brush Motor Drive Modules, 2-10
Brushless Motor, 2-33
Bus Power Supply
Fuse Location, 2-28
Bus Voltage, 1-3, 2-8
Bus Voltage Chart, 3-19
Bus Voltage Configuration, 2-8
Button C Joystick Input, 3-9
C
Cable Connections, 2-31, 3-17
Cables
Connections, 2-31
DIOSR/DRC, 2-33
Motor, 2-31
OP500, 2-33
Position Feedback, 2-31
Card Rails, 1-4
CCW Limit Axis 1 Pinout, 3-6
CCW Limit Axis 3 Pinout, 3-6
CCW Motor Rotation
Stoping, 3-6
Circuit
Shunt Regulator, 1-4
Cleaning, 5-6
Commanding DC Brush Motors, 3-8
Configuration
AC Brushless Drive, 2-24
AC Brushless Linear Drive, 2-26
Brush Drive, 2-11
Jumpers, 2-10, 2-11
Stepper Drive, 2-22
Configurations of the slot jumpers, 2-3
Configuring Slot Jumpers, 2-2
Connecting Cables, 2-32
Connecting Drive Modules, 2-32
Connector Pinouts
AC Brushless Motor, 3-15
DC Brush Motor, 3-15
I/O or Opto-22 Bus Connector, 3-14
Motor Power, 3-15, 3-16
Stepper Motor, 3-15, 3-16
Connectors
15 Pin, 3-11, 3-12
25 Pin, 3-10, 3-12
From UNIDEX 500/600 P1, 2-33
From UNIDEX 500-P5/UNIDEX 600-P10, 2-33
I/O Bus, 3-7
J11, 3-7
J2 to J5, 3-10
Index
i