Mitsubishi Electric 800 Series Instruction Manual page 43

• Remote registers
*4
Address
Upper 8 bits
RWwn Monitor code 2
Set frequency (0.01 Hz increments) /
RWwn+1
torque command
Link parameter
RWwn+2
extended setting
RWwn+3 Data to be written
RWwn+4 Monitor code 3
RWwn+5 Monitor code 4
RWwn+6 Monitor code 5
RWwn+7 Monitor code 6
*1 When Pr.804 = "3 or 5" during torque control under Real sensorless vector control, a torque command value is set in RWwn+1.
*2 The display can be changed to rotations per minute (machine speed) using Pr.37 and Pr.53.
*3 When the output frequency or the set frequency is selected as the monitor item, rotations per minute (machine speed) can be displayed using
Pr.37 and setting "4" in Pr.53.
*4 "n" indicates a value determined by the station number.
 When Pr.544 = "14" (Compatible with the quadruple setting of CC-Link Ver.2)
• Remote I/O signals
Settings are the same as those when Pr.544 = "0". (Refer to
• Remote registers
*4
Address
Upper 8 bits
RWwn Monitor code 2
RWwn+1
Set frequency (0.01 Hz increments)
Link parameter
RWwn+2
extended setting
RWwn+3 Data to be written
RWwn+4 Monitor code 3
RWwn+5 Monitor code 4
RWwn+6 Monitor code 5
RWwn+7 Monitor code 6
RWwn+8 Fault record No.
RWwn+9
PID set point (0.01% increments)
RWwn+A
PID measured value (0.01% increments)
RWwn+B
PID deviation (0.01% increments)
RWwn+C Torque command or torque limit
RWwn+D
RWwn+E H00 (Free)
RWwn+F
*1 When Pr.128 = "50, 51, 60, or 61", the register is valid. When Pr.128 = "1000 to 2011", the register is valid depending on the setting in Pr.609 or
Pr.610.
*2 The display can be changed to rotations per minute (machine speed) using Pr.37 and Pr.53.
*3 When the output frequency or the set frequency is selected as the monitor item, rotations per minute (machine speed) can be displayed using
Pr.37 and setting "4" in Pr.53.
*4 "n" indicates a value determined by the station number.
 When Pr.544 = "18" (Compatible with the octuple setting of CC-Link Ver.2)
• Remote I/O signals
Settings are the same as those when Pr.544 = "0". (Refer to
• Remote registers
*4
Address
Upper 8 bits
RWwn Monitor code 2
RWwn+1
Set frequency (0.01 Hz increments)
42
2. Ethernet Communication
2.6 CC-Link IE Field Network Basic
Description
Refer to
Lower 8 bits
Monitor code 1 45
46
*1*2
Instruction code 46
46
46
46
46
46
Description
Refer to
Lower 8 bits
Monitor code 1 45
*2
46
Instruction code 46
46
46
46
46
46
H00 46
*1
46
*1
46
*1
46
46,
—
Description
Refer to
Lower 8 bits
Monitor code 1 45
*2
46
*4
Address
page
Upper 8 bits
RWrn
First monitor value
RWrn+1
Second monitor value
RWrn+2 Reply code 2
RWrn+3 Data to be read
RWrn+4
Third monitor value
RWrn+5
Fourth monitor value
RWrn+6
Fifth monitor value
RWrn+7
Sixth monitor value
page 40.)
*4
Address
page
Upper 8 bits
RWrn
First monitor value
RWrn+1
Second monitor value
RWrn+2 Reply code 2
RWrn+3 Data to be read
RWrn+4
Third monitor value
RWrn+5
Fourth monitor value
RWrn+6
Fifth monitor value
RWrn+7
Sixth monitor value
RWrn+8 Fault record No.
RWrn+9 Fault record (output frequency)
RWrn+A Fault record (output current)
RWrn+B Fault record (output voltage)
52 RWrn+C Fault record (energization time)
RWrn+D
RWrn+E H00 (Free)
RWrn+F
page 40.)
*4
Address
page
Upper 8 bits
RWrn
First monitor value
RWrn+1
Second monitor value
Description
Refer to
Lower 8 bits
*3
47
*3
47
Reply code 1 47
47
*3
47
*3
47
*3
47
*3
47
Description
Refer to
Lower 8 bits
*3
47
*3
47
Reply code 1 47
47
*3
47
*3
47
*3
47
*3
47
Fault record (fault
47
data)
47
47
47
47
—
Description
Refer to
Lower 8 bits
*3
47
*3
47
page
page
page