Mitsubishi Electric 800 Series Instruction Manual page 76

Object identifier Object name
310
PID set point CMD
PID measured value
311
*2
CMD
312
PID deviation CMD
398 Mailbox parameter
399 Mailbox value
10007 Acceleration time
10008 Deceleration time
*1 R: Read only, W: Read/Write (Commandable values not supported), C: Read/Write (Commandable values supported)
Values written to the objects that support the commandable values are stored in the Priority Array, even when "Write Access Denied" is returned
due to inconsistency of the writing requirements such as the operating mode, on condition that the values are written within the setting range.
*2 If communication speed command source is other than NET, the setting value can be written, but not to be applied.
*3 When both C42 and C44 ≠ "9999", the setting range is from the smaller coefficient to the larger coefficient of C42 and C44. Depending on the
setting, the writing value and the reading value may not be the same at the minimum digit.
*4 When Pr.133 ≠ "9999", the Pr.133 setting is valid.
• BINARY INPUT
Object identifier
0 Terminal DI0
1 Terminal DI1
105 Terminal ABC
107 Terminal SO
*1 R: Read only, W: Read/Write (Commandable values not supported), C: Read/Write (Commandable values supported)
• BINARY OUTPUT
Object identifier
5 Terminal ABC CMD
Present value
*1
access type
*2
C
C
*2
C
W
W
W
W
Present value
Object name
access type
R
R
R
R
Present value
Object name
access type
C
Description
Set the PID action set point.
• This object is the set point during PID operation if
Pr.128 = "60 or 61". (Setting range: 0.00 to 100.00)
• This object is the set point during PID operation if
Pr.128 = "1000 or 1001" and Pr.609 = "4". (Setting
*3*4
range: 0.00 to 100.00)
• This object is the set point during PID operation if
Pr.128 = "2000 or 2001" (not applied to the
frequency) and Pr.609 = "4". (Setting range: 0.00 to
*3*4
100.00)
Set the PID measured value.
• This object is the measured value during PID
operation if Pr.128 = "60 or 61". (Setting range: 0.00
*3
to 100.00)
• This object is the measured value during PID
operation if Pr.128 = "1000 or 1001" and Pr.610 = "4".
(Setting range: 0.00 to 100.00)
• This object is the measured value during PID
operation if Pr.128 = "2000 or 2001" (not applied to
the frequency) and Pr.610 = "4". (Setting range: 0.00
*3
to 100.00)
Set the PID deviation. (0.01 increments)
• This object is the deviation during PID operation if
Pr.128 = "50 or 51". (Setting range: -100.00 to
100.00)
• This object is the deviation during PID operation if
Pr.128 = "1010 or 1011" and Pr.609 = "4". (Setting
range: -100.00 to 100.00)
• This object is the deviation during PID operation if
Pr.128 = "2010 or 2011" (not applied to the
frequency) and Pr.609 = "4". (Setting range: -100.00
to 100.00)
Access to the properties which are not defined as
objects are available. (Refer to page
Set Pr.7 Acceleration time.
Set Pr.8 Deceleration time.
*1
(0: inactive, 1: active)
Represents actual input of terminal DI0.
Represents actual input of terminal DI1.
Represents actual output of terminals A, B, and C.
Represents actual output of terminal SO.
*1
(0: inactive, 1: active)
Controls actual output of terminals A, B, and C.
Control is available when Pr.192 ABC terminal function
selection = "82 or 182"
Unit
*3
no-units
(95)
no-units
(95)
*3
percent
(98)
no-units
(95)
76.)
no-units
(95)
seconds
(73)
seconds
(73)
Description
Description
*2
.
2. Ethernet Communication
2.8 BACnet/IP
1
2
3
4
5
6
7
8
9
10
75