Input Channel − Fx Sends; Fx Signal Flow - QSC TouchMix-30 Pro User Manual

Input Channel − FX Sends
Controls how much of the Input channel's audio is sent to the
FX devices.
1. Selects the FX Sends screen.
FX tab –
2.
FX Overview button –
Overview screen for a view of all 6 FX sends from all inputs.
3. Hides the Global FX
Simple button –
Parameters for simplified operation.
4. Resets the FX sliders, Pre/
Reset button –
Post settings, and the Pitch Correct settings. This
button does not reset the settings for the FX processors
including the Global FX Parameters on this screen.
5. – The thumbnail representation of
FX Buses
the FX processor takes you to a screen where you can
select the processor for that FX send, and adjust the
parameters for the selected FX processor.
6. FX Label – The larger text identifies the FX bus number,
and does not change. The smaller text can be changed
in the FX processor Setup screen.
7.
FX Send sliders –
sent from the channel to the FX mix; "-inf" is off. The
digital read-out to the right of the slider indicates the
slider setting.
8.
Global FX Parameters –
control over the two most important parameters of the
selected FX device. The parameters will differ depending on the selected processor.
9.
Pre/Post Fader button –
pick-off for all inputs.
10. – Refer to the Pitch Correct topic.
Pitch Correct

FX Signal Flow

Input audio passes through the EQ, and Dynamics (compressor and gate). At this point you can split the audio and send it to the FX system (Pre-fader), then the
Channel Fader. Or, send the audio through the Channel Fader then split it and send it to the FX system (Post-fader).
"Dry" audio (no FX processing) continues through the Pan control to the Main L/R Fader and Main outputs.
The Pre-fader or Post-fader audio is sent to the Channel FX sends (The diagram shows just one of the FX Sends).
The FX Send slider determines how much of the channel audio is sent (or routed) to the assigned FX processor.
The FX processor works its magic on the audio and transforms the mono input into a stereo signal. The FX Master fader controls how much or how little of the
processed ("wet") signal is combined with the unprocessed ("dry") audio before going to the Main L/R fader and on to the Main L/R outputs.
Audio Input
Input Channels
NOTE: For detailed information, refer to the Block Diagram.
1001108-01-F
Navigates to the FX Main Mix
L/R
Joe's Monitor
Aux 1
Aux 2
Aux 2
Aux 3
Aux 3
Aux 4
Aux 4
Aux 5
Aux 5
Aux 6
Aux 6
Aux 7
Aux 7
Aux 8
Aux 8
Aux 9
Aux 9
Aux 10
Aux 10
Aux 11
Sets the level of audio
Aux 11
Aux 12
Aux 12
Aux 13
Aux 13
Aux 14
Provides
Aux 14
Selects a pre-fader or post-fader (default) pick-off point for the FX send. Changing this setting will change the
Channel
Fader
EQ Dynamics
Pre
FX
-40 -20
Send
Home
Input 1-8
In 1 FX
Inputs 1-8
Overview EQ Comp Gate
FX Buses
6
5
Chorus FX 1
Joe's FX
-40 -20 -10 U
7
Dense Reverb
FX 2
FX 2
-40 -20 -10 U
Lush Reverb FX 3
FX 3
-40 -20 -10 U
Mono Delay
FX 4
FX 4
-40 -20 -10 U
None
FX 5
FX 5
-20 -10 U
-40
Basic Chorus FX 6
FX 6
-40 -20 -10 U
10
Pitch Correct
Enable Key E
Channel
10 10
Pan
5
u
5
10
L C R
20
40
Post
10 10
5
u
-10 -5 U 5 10
5
10
20
40
FX
FX
Master
47
Touch an Touch a
Input Bank Channel
1
FX Auxes Presets Setup
2 3 4
FX Overview Simple Reset
Pre/Post
Global FX Parameters
Fader
8 8 9
Hz
Rate Depth
10
-11.5 2.3 0.63 Pre
Sec mSec
Rev Time Initial Delay
10
-23.0 34.0 0.00 Post
mSec
m
Size Pre Delay
10
-inf 1.43 0.5 Pre
mSec %
Delay Regen
10
-inf 1.7 0.5 Pre
Param 1 Param 2
10
-inf 32 0.00 Pre
Hz
Rate Depth
10
-inf 1.5 0.5 Pre
Blend Correct
20% 8.3
Amount Rate
Dry Wet Slow Fast
Main
Main
L/R
Left
10 10
5
u
5
10
20
40
∞
Main
Right
Touch the
FX Tab
Scene:
Default
Next
Prev
In 1 Main
Cue Cue
L C R
Mic Main
1 L/R
10 10
10 10
5 5
L
u
u
L
F
5
G
5
48
10
10
20 20
0 0
LR
40 40
1 2
3 4
∞ ∞
5 6
7 8
Mute Mute