Mixer Setup - QSC TouchMix-30 Pro User Manual

Mixer Setup

Controls for various global and utility functions.
1. Sets the function of the channel
Cue Mode –
Cue buttons.
• Cue (Default)– Touching a channel cue button
causes the channel's signal to be heard in the
Cue headphones. The audio signal is otherwise
unaffected.
• SIP (Solo In Place) – Input Cue buttons change
color (orange) and are labelled SIP. Touching
a channel's SIP button causes all other inputs
to mute. Cue continues to function normally
for outputs. SIP is a very useful setup function
but can produce unwanted results if left on
during performance.
2. Determines if the Cue signal
Cue Pickoff –
is derived pre or post-fader.
• (Pre-Fader Listen)
PFL
• (After-Fader Listen)
AFL
3. Selects the sample
Sample Rate –
frequency (bit rate) for the mixer. Most relevant
for recording. Typically, 44100 is used for audio
CD, and 48000 for audio with video.
4.
Dynamics Processing (global) –
Determines whether all input channel gates and
compressors are controlled by a pre or post EQ
signal.
5. and
Demo Mode Confirm Mute
•
Demo Mode (Mixer only) –
control turns the demo on/off.
•
Confirm Mute on Master (tablets only) –
This switch eliminates the confirmation step.
6.
Omit Levels on Paste Overview –
7.
Display Brightness –
8.
Save System Log to USB –
9. Clear Storage – Deletes all user-defined presets and scenes from the mixer. Does not delete presets or scenes stored on a USB
device.
10. Resets all mixer controls to factory default. This does not erase any user presets on the mixer or on a USB drive.
Reset Mixer –
11.
Software Version Label –
12.
Start Upgrade (Must Download First) –
www.qsc.com for upgrade instructions and to download the latest firmware version, or go to the following step.
13.
Check and Download Upgrade –
and TouchMix-16 with version 3.0 or higher. You must have an Internet connection and a USB drive (with about 250 MB free) to
download the upgrade files. When you use this method, follow the instructions on the screen. The mixer checks for the latest version,
and downloads it automatically. If you have the latest version, you will get a message indicating that.
NOTE: For the TouchMix-30 Pro the Internet connection can be wired, or wireless via a compatible wireless adapter
(Part # CP-000033-00 is available from QSC) connecting to a wireless router with Internet access.
For the TouchMix-8 and TouchMix-16 you must connect via the wireless adapter to a wireless router with Internet access. or to a
router using a USB to Ethernet adapter.
14.
End User Agreement –
1001108-01-F
Menu
Main Mix
L/R
Joe's Monitor
Aux 1
Aux 2
Aux 2
1
Aux 3
Aux 3
2
Aux 4
Aux 4
Aux 5
3
Aux 5
Aux 6
4
Aux 6
Aux 7
Aux 7
5
Aux 8
Aux 8
6
Aux 9
Aux 9
Aux 10
Aux 10
Aux 11
Aux 11
Aux 12
Aux 12
Aux 13
Aux 13
Aux 14
Aux 14
The mixer is set at the factory to display a slide show of features until the screen is touched. This
Provides an option to omit all level settings when pasting to an overview screen.
Controls the brightness of the LCD screen and illuminated buttons.
Writes a file to USB that may be useful in software troubleshooting.
Displays the version number of the currently installed firmware.
Begins the process of upgrading mixer software. Before starting, either visit
This function is available on TouchMix-30 Pro with version 1.1 or higher and TouchMix-8
Displays the End User License Agreement for your reading pleasure.
Mixer Setup
Demo Mode
8 9
Save System Log to USB
12
11
Start Upgrade
(must download first)
By default, muting a master output (Main or Aux bus) requires a confirmation.
96
Press Menu
Display Brightness
7
1.00
10
Clear Storage Reset Mixer
13 14
Check and Download
End User Agreement
Upgrade
Touch Mixer
Setup
Scene:
Default
Main
Cue
Main
L/R
10 10
5
L
u
F
5
10
20
0
40
∞
Mute