Agilent Technologies 1200 Series Reference Manual page 253

N
non-operating altitude, 14
non-operating temperature,
not-ready condition, 46
O
onboard battery, 216
operating Altitude, 14
operating temperature, 14
operational hints, vacuum degasser,
operational pressure range,
optimum performance, 18
optional interface board, 221
outlet ball valve, 104, 178
outlet capillary, 167
overview, pump, 203
P
parity settings, 232
parts
active inlet valve, 180
bottle head assembly, 166
control module, 164
cover, 169
damaged, 15
foam, 171
hydraulic path, 167
leak handling, 173
light pipes, 172
main assemblies, 162
missing, 15
outlet ball valve, 178
pump head, 174
pump head with seal wash,
pump housing and main
assemblies, 163, 164
sheet metal kit, 170
solvent cabinet, 165
parts identification
cable overview, 184
cables, 183
cables - analog, 186
cables - APG remote, 189
cables - auxiliary, 196
cables - BCD, 194
cables - CAN, 197
1200 Series QP Reference Manual
cables - external contact,
cables - LAN cables,
performance specification,
14
pH range,
physical specifications,
piston, 32, 112,
piston chamber,
plateaus, leak test,
power consideration,
power consumption,
power cords,
36
power light pipe,
238
power supply,
power supply indicator,
power supply lamp,
power switch,
power-input socket,
prerun condition,
pressure,
pressure above upper limit,
pressure below lower limit,
pressure converter,
pressure pulsation, 40, 207,
pressure range,
pressure sensor readings,
pressure test, 44,
pressure, operating range,
priming
with a pump, 27,
with a syringe, 27,
with the pump,
proportioning valve, high-spped,
PTFE frit, 16,
pump configuration,
pump drive,
pump head assembly,
176
pump head missing,
pump head with seal wash,
pump piston,
purge valve,
purge valve frit,
purging the pump,
R
rear of pump,
reassembling the pump head,
recommended pH range,
remote
198
200
238
238
14
204
203
92
12
14
12
172
148
45
45
21
12
46
203
61
62
215
238
39
22
82
238
28
36
36
203
106
65
144
174
75
176
32
106
32
27
22
121
238
signal distribution, 226
remote interface, 226
removing
pump head assembly, 108
the foam, 127
the top cover, 127
repairs, 99
using the ESD strap, 97
replacing the foam, 157
replacing the top cover, 157
restart without cover, 59
results, pressure test, 85
RS-232C
cable kit to PC, 199
RS-232C communication settings,
RS-232C connection table, 227
RS-232C interface, 227
run mode, 46
running the leak test, 89
running the pressure test, 83
S
safety
standards, 14
safety light switch, 126, 129,
sapphire piston, 204
screwdriver pozidriv #1, 127, 139, 142,
144, 148, 153, 155, 157
seal
wear-in, 111
seal insert tool, 16
seal wash, 38, 202, 203
installing, 114
when to use, 38
seal wear counters, 212
seal, alternative material, 39
seals, 109, 112, 114, 118, 121
security lever, 22, 96
selection valve failed, 63
serial number
entered on instant pilot, 134,
servo restart failed, 74
setable flow range, 238
setting
baudrate, 231
data bit, 231
forced cold-start, 232
parity, 232
Index
231
157
136
253