Talkback - Solid State Logic Matrix2 Delta Owner's Manual

Artist's Monitoring
Matrix has an additional output for the artist's headphones, which is controlled by the
section, to the right of the
the artist's monitoring. The sources available are (from bottom to top) the
the CUE bus, the desk's
inputs (EXT1). Each button lights to indicate which is active.
2SXI XLEX [LMPI XLI SXLIV FYXXSRW PMKLX ]IPPS[ XLI
Normally these buttons cancel each other. However, the summing button (Y PSGEXIH MQQIHMEXIP] EFSZI XLI ½ZI WSYVGI WIPIGXSV
buttons, removes the intercancelling feature and instead sums all selected inputs, enabling multiple sources to be monitored
simultaneously. Deselecting the Y button cancels all monitoring sources and returns the artist's monitor to intercancelling mode.
The ARTIST MONITOR
and Total Recall LEDs. This is located in the top right of the
switched into the circuit by pressing the
EQ pots are indented in the centre.
The pot in the bottom right is a gain control for the artist monitor output. The
above it reduces the feed to mono.
Engineer's Headphones
There is an engineer's headphone output located in the trim on the right hand side of Matrix, close
to the large navigation wheel. It is controlled by the area above the transport counter, consisting
of a HEADPHONE gain pot and a
from the control room monitor mix to the artist's monitor mix (see above). The button lights to
indicate that the feed has been switched to the artist's mix.
While the FROM ARTIST
selection in the MAIN MONITOR
affected by the DIM, CUT,
Conversely, when FROM ARTIST
selection, EQ insert and

Talkback

The engineer can talk to the artist by pressing and holding the
navigation wheel in the centre section. This sends the signal from the desk's inbuilt talkback microphone to the
ARTIST
artist's monitor feed.
The talkback microphone is located above the
(shown right). Its level is set by the
DIM function is automatically activated in the main monitoring.
The action of the talkback switch may be changed from momentary to latching by engaging the
"TB Latch" switch within the
2SXI XLEX XLI XEPOFEGO JYRGXMSR GER EPWS FI EWWMKRIH SRI SJ XLI X[S VIEV TERIP JSSX W[MXGL MRTYXW ZME XLI
1EXVM\ 6IQSXI 7II 4EKI  for more details
2SXI EPWS XLEX XLI XEPOFEGO HSIW RSX JIIH XLI IRKMRIIV´W LIEHTLSRI WMKREP IZIR [LIR XLI
FIIR WIPIGXIH
MAIN MONITOR controls. The six buttons on the left hand side select the signal which is feeding
DIGITAL external monitor input (see Page 45  ERH XLI ½VWX SJ XLI X[S EREPSKYI I\XIVREP QSRMXSV
has available a 2-band EQ with high-pass and low-pass shelving controls
EQ button located in between the
FROM ARTIST
button is not selected, the headphone signal follows the source
area, along with the
MINI or level controls.
is selected, the engineer's headphone signal follows the
MONO button, but is not affected by the level control.
SSL > MonOpt
MIX
MON FYW PMKLXW KVIIR MR OIITMRK [MXL MXW GSPSYV GSHMRK
ARTIST MONITOR
HF
button which switches the headphone feed
øL and MONO
MAIN MONITOR
TB gain trim immediately above it. When it is pressed, the
menu.
Chapter 3 - Analogue Signal Flow
ARTIST MONITOR
bus, the control room monitor output (MON),
area, and can be
and LF pots. Both
iJack
MONO button
buttons, but is not
ARTIST MONITOR
ARTIST button located to the left of the large
area of the centre section
FROM ARTIST
Matrix 2 Owner's Manual
area of the centre
source
DAW XEF MR XLI
FYXXSR LEW
40