Solid State Logic Matrix2 Delta Owner's Manual page 42

REC and MIX Busses
In addition to the CHOP, the channel's main fader can feed the record and/or mix bus.
These are selected using the
Channel which light up to indicate the presence of routing. This routing is also indicated
by the lighting of the
1
the channel (shown left). You will notice that throughout the desk, references to the
REC bus are red, references to the
bus are green.
The signal level being sent to the record and mix busses is controlled by the fader at the bottom of the channel. The channel's
feed to the record and mix busses is panned using the pan pot towards the bottom of the routing section of the channel strip
(shown below), which includes a Total Recall LED. The pot is indented in the middle, where the signal is feeding both the left
and right busses equally.
DAW Monitor Mode
When
DAW MONITOR
PSGEXIH FIPS[ XLI GLERRIP WXVMT´W TER TSX WLS[R PIJX ERH GSR½KYVIW XLI GLERRIP JSV
recording following the classic in-line style of previous generation SSL consoles. The
signal received from the input is routed through any processing applied via the Insert
Matrix and then to the DAW via the channel output.
With DAW MONITOR
the CHANNEL OUT (post-gain) output (the DAW send) and the DAW RTN input (pre-gain).
Both the Master Channel's
mode is active. The colour of the
yellow for channel out.
When the DAW MONITOR
button above it. AUTO MON
source on any channels in
- When the transport is idle the monitoring source for these channels will be the channel output.
- When the transport is in Play the monitoring source will be the DAW return.
 ;LIR XLI (%; ERH XLI (%; XVEGO EWWSGMEXIH [MXL XLI GLERRIP MW MR VIGSVH XLI QSRMXSV WSYVGI ¾MTW FEGO XS XLI
channel output.
2SXI XLEX JSV XLI DAW MONITOR
SYXTYX QYWX FI WIRHMRK XS XLI 1EXVM\ GLERRIP [LMGL MW JIIHMRK MXW MRTYX
2SXI EPWS XLEX MR SVHIV XS YWI
WSYVGI QYWX RSX FI TSWXJEHIV
Cut and Solo
Above the fader, there is a
which mutes all other channels, leaving that channel as the only signal reaching the monitors.
REC
REC and MIX
INPUT has been selected as the channel source, pressing the
button in the Master Channel (shown right) enables the
mode active, pressing
DAW MONITOR button and the channel strip's
TRK button also indicates which monitoring source is selected: green for DAW return and
mode is active, full zero latency drop in and Record monitoring is available via the
allows the desk to take control of the
DAW MONITOR mode depending on the status of the DAW transport and track record tally:
JYRGXMSR XS W[MXGL FIX[IIR GSVVIWTSRHMRK (%; WIRHW ERH VIXYVRW IEGL (%; XVEGO
DAW MONITOR
CUT
7II 4EKIW  and  JSV HIXEMPW SJ XLI HMJJIVIRX WSPS ERH GYX QSHIW EZEMPEFPI SR 1EXVM\
and MIX bus buttons at the bottom of the Master
symbols at the bottom of the meter section above
MIX bus are yellow, and references to the
TRK switches the monitoring source for that channel between
TRK
QSHI XLI GLERRIP MRTYX QYWX FI WIX XS INPUT ERH XLI
switch which immediately mutes the channel's output, and a
Chapter 3 - Analogue Signal Flow
MON
TRK button,
TRK button light up to indicate that DAW Monitor
buttons, automatically switching the monitoring
Matrix 2 Owner's Manual
AUTO MON
CHOP
SOLO button
34