Extra Setup Information For Using A-Fada With Logic - Solid State Logic Matrix2 Delta Owner's Manual

Chapter 3 - Analogue Signal Flow
Now you are ready to engage A-FADA. Press the
presumes you want your DAW on DAW layer 1 to control Matrix's channels. Simply press the
faders now control Matrix's analogue gains.
-J ]SY [MWL XS YWI XLI (%; ]SY LEZI GSR½KYVIH SR (%; PE]IV  XLIR TVIWW XLI
2SXI 8LIWI  EYHMS XVEGOW QYWX FI TSWMXMSRIH EW XLI ½VWX  MR XLI WIWWMSR EW XLI ,9-1'9 TVSXSGSPW HMGXEXI XLMW
8MT =SY TVSFEFP] [ERX XS VIREQI XLIWI %YHMS 8VEGOW XS LEZI QIERMRKJYP REQIW WYGL EW ³/-'/´ MRWXIEH SJ ³%YHMS´
The Snap function
8LI WRET JYRGXMSR ½VIW E WRETWLSX SJ XLI GSRWSPI EREPSKYI JEHIV TSWMXMSRW EYXSQEXMGEPP] WXSVIH [LIR %*%(% QSHI MW IREFPIH
(when you press the DF button). When A-FADA mode is enabled, the console faders will move to match the current DAW fader
positions. Pressing the Snap
to be restored and written into the DAW automation.
Operating A-FADA
Once A-FADA mode has been enabled, the console faders will control the corresponding DAW faders, and the fader position
signal from the DAW will control the console fader positions and analogue gain, regardless of the selected Focus mode.
In Analogue Focus the channel cut switches control the analogue cuts directly, while in DAW Focus they are routed via the
DAW and will be recorded as mute automation. Analogue Focus mode allows channels to be muted as far as monitoring the mix
is concerned, without writing mute automation or needing to change automation modes.
The console solo switches are connected to the analogue signal path in both Focus modes.
In order to lock console channels to the same DAW track (and thus its automation), Channel/Bank scrolling is disabled in
A-FADA mode.

Extra Setup Information for using A-FADA with Logic

You need to ensure that Logic's Control Surfaces Preferences are set correctly. Go to
Ensure that the options 'Touching Fader Selects
and Solo buttons' are all un-ticked.
-X MW EPWS VIGSQQIRHIH XS WIX XLI 0SKMG 1M\IV XS ³%VVERKI´ ZMI[ QSHI 8LMW IRWYVIW XLEX XLI ½VWX  ³GSRXVSP XVEGOW´ EP[E]W
correspond to Matrix's 16 analogue channels. If using Instrument tracks with Multi Outputs, also ensure that the 'Link' button is
disabled, to prevent Logic automatically switching back to 'All' view mode when you click on an instrument.
0SKMG 8MT  &IGEYWI %*%(% [MPP ³PSGO SYX´ XLI 'LERRIP&ERO OI]W MR 0SKMG ]SY GER YWI ³'SRXVSP 7YVJEGI +VSYTMRK´ XS YWI
ERSXLIV (%; PE]IV EW ]SYV GSRXVSP WYVJEGI *SV I\EQTPI MJ ]SY [IVI YWMRK (%;  JSV %*%(% ]SY GSYPH YWI (%;  JSV
KIRIVEP GSRXVSP WYVJEGI TYVTSWIW 7MQTP] EHH ERSXLIV 1EGOMI 'SRXVSP ERH )\XIRHIV JSV XLMW PE]IV ERH XLIR HVEK XLIQ FIRIEXL
XLI I\MWXMRK SRIW MR XLI WIXYT TEKI MR 0SKMG
62
Matrix 2 Owner's Manual
SSL
switch will move the faders back to the previously stored positions, allowing the analogue balance
Track',
button on the Matrix and then press the
'Control surface follows track
Auto button. This example
DF1 button and your DAW
DF2 button instead.
Preferences > Control
selection' and
Surfaces.
'Flash Mute