Step 4: Sending To The Auxiliary Sends - Solid State Logic Matrix2 Delta Owner's Manual

Chapter 2 - Getting Started

STEP 4: Sending to the Auxiliary Sends

1EXVM\ LEW WM\ EY\MPMEV] WIRHW XLI ½VWX X[S JSVQMRK XLI 7XIVIS 'YI
for musicians) and the remaining four labelled
³ Check that the gain pots for the overall bus levels, located in the top right corner of the centre section
is shown right), are all set to 0dB, with the white line pointing towards the meters. This will allow you to
see what happens in the meters when you turn the pots in the channel.
8LI ½VWX X[S TSXW FIRIEXL XLI
will cover in Step 8. The stereo cue functions similarly to the FX sends which we will
concentrate on here: The two pots below the stereo cue are the gain trim for the FX busses. FX1 and 3 share
a pot, as do FX 2 and 4.
³
Press the upper gain pot, labelled FX1/3, to switch on FX1. The LED below it and to the right will light to
indicate that it is on.
³
9WI XLI TSX XS EHNYWX XLI KEMR YWMRK XLI
³
In the Master Channel, press the button marked FX3. This swaps the
the
has been made, as will the
blank and the
automatically to the
FX busses 2 and 4 work in exactly the same way as FX busses 1 and 3, using the next gain pot down.
Once you have sent signal to the aux busses, you need to set the overall output level of the bus. Each aux bus
LEW MXW S[R GSRXVSP EVIE ERH ]SY LEZI EPVIEH] PSSOIH XLIVI XS GLIGO XLEX XLI] EVI XYVRIH YT WYJ½GMIRXP] *SV
this tutorial, we will use FX3, as well as
³ In the
FX3 EVIE MR XLI ZIV] GSVRIV SJ XLI GIRXVI WIGXMSR XYVR XLI KEMR TSX XS EHNYWX XLI SYXTYX WMKREP PIZIP
³ Press the AFL button in the
monitoring.
³ In the
ST RET 3 area, located below FX sends 1 and 2, press
bus. You should now hear the processing you created added to the clean CD signal in the monitoring.
³ Press the
AFL button below the
³ %HNYWX XLI PIZIP SJ XLI VIXYVR YWMRK XLI KEMR XVMQ ERH XLI PIJXVMKLX FEPERGI YWMRK XLI TSX EFSZI XLI KEMR XVMQ
³ Press the
MONO button above the balance control. This reduces the stereo return to mono. The balance
pot will now be a pan pot. Press the
³ Press the
AFL button again to return to normal monitoring.
*SV QSVI MRJSVQEXMSR SR EY\MPMEV] WIRHW MRGPYHMRK EPXIVMRK XLI TSMRX MR XLI GLERRIP [LMGL JIIHW XLIQ WII 4EKI 
21
Matrix 2 Owner's Manual
FX 1-4
CHOP
FX1 send level to controlling the
FX3
FX3 QIXIV RS[ VI¾IGXW XLI '( TPE]IV 8LI WIXXMRKW ]SY GVIEXIH JSV XLI
FX3 send.
ST RET 3
FX3 area to listen to the
ST RET 3 gain trim to listen to the signal on its own.
MONO
CUE ST) send (which you will probably use for monitoring
(which you will probably use for feeding global effects such as reverb units).
are the pan and gain trim for the
FX1 meter to the right of the VU's as a reference.
FX3 send level. The
LED to the right of the
(Stereo Return 3, shown right).
FX3 bus send. Press it again to return to normal
MIX to send the returning signal to the mix
button again to restore the return to stereo again.
CUE ST, which we
FX1/3 gain pot from controlling
FX3 button will light to indicate that this swap
FX1/3 pot. Notice that the
(FX1
FX1 meter has gone
FX1 send transfer