Solid State Logic Matrix2 Delta Owner's Manual page 96

Chapter 5 - DAW Control
Param Mode
Param mode, activated either by pressing V-Sel 16 or by pressing any of the inserts which are currently assigned, brings the
parameters of the plug-in on the currently selected track insert into the plug-in editor. The plug-in parameters are accessed
using V-Sels and V-Pots 9, 10, 11 and 12. The upper row of the scribble strip displays any parameter switch options controlled by
the V-Sels, and the lower row on the scribble strip displays the parameters controlled by the V-Pots. In
scrolls between the pages of plug-in parameters. When a new page is accessed, the current page is displayed momentarily (along
with the number of parameter pages) in the top row of the scribble strip, in Channels 9 and 10.
V-Sel 7 and 8 are always assigned to the
Auto Set Mode
AUTO SET mode allows you to change the automation status of the DAW tracks via the console V-Sel switches. In this mode, the
V-Pots have no function and the V-Sels no longer control their corresponding DAW track.
For MCU DAWs, AUTO SET
V-Sels 9-12. These modes are labelled on the bottom row of the scribble strip directly above the V-Pot. The Automation Mode
on the currently selected channel will be indicated by all the indicator LEDs illuminating around the V-Pot whose V-Sel switch
corresponds to the active automation state. To change mode, simply operate the V-Sel switch for the new mode. Selecting
XLI 3** WXEXI JVSQ ER EGXMZI QSHI VIUYMVIW XLI 6)%( W[MXGL XS FI WIPIGXIH X[MGI 9WI XLI ETTVSTVMEXI KPSFEP QSHM½IV OI] MR
GSRNYRGXMSR [MXL XLI :7IP W[MXGL XS XSKKPI XLI EYXSQEXMSR WXEXI SJ EPP XVEGOW
2SXI XLI EFSZI I\TPEREXMSR VIJIVW XS GLERKMRK EYXSQEXMSR QSHIW MR 0SKMG
SXLIV 1'9 GSRXVSPPIH (%;W 4PIEWI GSRWYPX XLI VIPIZERX HSGYQIRXEXMSR XS HIXIVQMRI MJ EYXSQEXMSR GSRXVSP WYTTSVXW XLI
WEQI GSRXVSPPIV GSHIW EW 0SKMG
In Pro Tools, AUTO SET
When AUTO SET is pressed, the bottom row of the digital scribble strip for Channels 1-6 and 9-14 displays the Pro Tools
automation modes, while the top row of the digital scribble strip displays the currently active Pro Tools track names. When a
channel's DAW SEL key is pressed, the track name in the scribble strip is replaced by a display of that track's current automation
mode. The track's automation mode can now be altered by pressing the V-Sel buttons below each of the automation mode labels.
You will notice that the red
GLERRIP XLI 0)( ¾EWLIW [LIR ER] SJ XLI [VMXI QSHIW EVI WIPIGXIH ERH WXE]W PMX [LIR E XVEGO MW EGXMZIP] [VMXMRK EYXSQEXMSR HEXE
The green AUTO LED indicates Read Mode; Flashing red + green LEDs indicates if the trim state has been selected for any of
the write modes (Pro Tools HD only).
Either set of V-Sel buttons (ie. those found in Channels 1-6 or 9-14) can be used to set the automation mode on any active DAW
track. The automation mode on a range of tracks can be set together by selecting multiple
left-most DAW SEL key and pressing the right-most
faders retain their control of the DAW track faders and the mode can safely be left enabled in order to change state whilst Pro
Tools is in Play.
4PIEWI RSXI XLEX XLIVI EVI X[S
WXVMT EFSZI XLI HMKMXEP WGVMFFPI WXVMT ERH MW GSRGIVRIH [MXL XLI HIWO´W EREPSKYI VSYXMRK RSX (%; GSRXVSP
2SXI XLEX MR 4VS 8SSPW EYXSQEXMSR SJ WIRH PIZIP ERH TER JYRGXMSRW GER FI EGGIWWIH F] TVIWWMRK
QSHI WII 4EKI  
88
Matrix 2 Owner's Manual
Bypass
and
assigns the four Logic MCU automation commands to V-Sel switches 1-4, repeating them on
functions as follows:
AUTO LED above that channel strip indicates the automation status of the DAW track in that
SEL FYXXSRW MR XLI 1EXVM\ GLERRIP 8LI SXLIV
Compare
functions of the plug-in.
SEL key within the desired selection. In
AUTO SET QE] RSX FI JYPP] WYTTSVXIH F]
SEL keys. This is done by holding the
AUTO SET
SEL FYXXSR MW PSGEXIH JYVXLIV YT XLI GLERRIP
AUTO SET
Param
mode, V-Pot 16
mode, the channel
[LMPI MR FLIP