Page 1
Installing and Administering Avaya J100 series IP Phones in third-party call control setup Release 3.0 Issue 2 August 2018...
Page 2
RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU the express behalf of Avaya. End User agrees to indemnify and hold AND ANYONE ELSE USING OR SELLING THE SOFTWARE harmless Avaya, Avaya's agents, servants and employees against all WITHOUT A LICENSE.
Page 3
IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION written consent of Avaya can be a criminal, as well as a civil offense FOR H.264 (AVC) AND H.265 (HEVC) CODECS MAY BE under the applicable law.
Page 4
This device complies with Industry Canada licence-exempt RSS Avaya to be used with the equipment. If you use any standard(s). Operation is subject to the following two conditions: other equipment, it may cause failures, malfunctioning, 1. This device may not cause interference, and or fire.
Page 5
® ENERGY STAR compliance statement As an ENERGY STAR partner, Avaya Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Information on the ENERGY STAR program can be found at www.energystar.gov. ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S.
Chapter 5: Cloud configurations................... 85 ..................85 Configuration through a cloud server ................... 85 Phone setup process on a cloud server August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 7
Recents configuration ......................... 111 Contacts list ............111 Configuring Groups list by using the web interface ....................112 Contacts list configuration August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 8
Support Chapter 11: Appendix......................118 ................. 118 Appendix A: List of configuration parameters ..................177 Appendix B: Public CA Certificates August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Chapter 1: Introduction Purpose This document contains information about preparing Avaya J100 Series IP Phones for installation, deployment, initial administration, and administration tasks including data and security. This document is intended for the deployment engineers or support personnel who install, administer, and maintain Avaya J100 Series IP Phones.
Chapter 2: J100 Series IP Phone overview Avaya J100 Series IP Phones are series of phones that you can use for unified communication. The series leverages the enterprise IP network and eliminates the need of a separate voice network. It offers superior audio quality with amplified handset and customization with low power requirements in a Session Initiation Protocol (SIP) environment.
20dB of gain of gain of gain Wired Headset Expansion module Yes (3) Yes (3) capable Optional DC Power GSPPOE power adapter August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
J100 Series IP Phone overview Power specifications The J100 Series IP Phones can use different power sources like LAN based Power, the Global Single Port PoE Injector (GSPPOE) or power module (DC power jack). The following table lists the various power requirements with or without peripherals.
Page 13
Supported codecs Codecs J129 J139 J169 J179 • G722 • G722 • G722 • G722 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
List of Wi-Fi configuration parameters on page 17 J100 wireless module Avaya J129 IP Phone and Avaya J179 IP Phone support wireless module. The wireless module is an optional component and you can order this module separately. Note: Avaya J139 IP Phone and Avaya J169 IP Phone do not support the J100 wireless module.
Page 15
1. Insert the screw driver in the opening of the module panel to release the latch. Do not pry open the panel. 2. To remove the module panel, slide the panel out in the direction of the arrow. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 16
4. Use the Phillips #1 screwdriver to fasten the module. 5. Slide the module panel inward to close. Related links J100 wireless module on page 14 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 17
Wi—Fi • 2: Phone connects to the Wi— Fi network with the SSID Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 18
Wi-Fi regulatory domain. WLAN_ENABLE_80211D Enables the phone to configure its Wi-Fi regulatory domain to match the 802.11d. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 19
Specifies the 802.1x name of pre- configured Wi-Fi network. This parameter is applicable if WIFISTAT parameter is enabled Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 20
Code Point for signaling frames generated by the telephone. Valid value is from zero to 63. Related links Wi-Fi overview on page 14 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Wall mounting Avaya J100 Series IP Phones About this task Wall mounting kit and procedure of Avaya J100 Series IP Phones are similar except the wall mounting bracket. Wall mounting brackets look different for Avaya J169/J179 IP Phone and Avaya J129 IP Phone.
Page 22
The lower pair of tabs rest against the back of the phone and ensure that the phone does not move when the keys are pressed. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Installing the phone by using the DES eliminates the need of manual configuration of provision server. Note: DES only works if a provisioning server has been configured in the Avaya DES service for the phone's MAC address. This is configured by the service provider. Installing the phone using DES server After the phone boots up, it prompts to enable or disable DES discovery.
Page 24
Ensure that your network already has the following components installed and configured: • A DHCP server for providing dynamic IP addresses to the Avaya J100 Series IP Phones. • A file server, an HTTP or an HTTPS for downloading the software distribution package and the settings file.
Page 25
Use this checklist to gather, record, and verify the information during the installation. Task Reference Check the prerequisites Prerequisites on page 24 Administer the VLAN VLAN overview on page 27 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 26
N e t w o r k configuration Avaya Aura ® F i l e S e r v e r System Manager August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 27
VLAN tagged frame. Voice and video traffic typically get a higher priority in the network as they are subject to degradation caused by network jitter and delay. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 28
Initial setup and connectivity VLAN separation The Avaya J100 Series IP Phones has an internal network switch that is capable of using VLANs to segregate traffic between the LAN port, the PC port and the internal port that goes to the CPU of the phone.
Page 29
(PHY 1) (PHY2) ingress egress ingress egress LAN port PC port Internal Ethernet switch CPU port ingress egress Phone's CPU Phone August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 30
LAN port if they are untagged frames or tagged frames with VLAN ID= PHY2VLAN. In this mode, there is a complete separation between CPU port and PC port. In order to configure Avaya J100 Series IP Phones to work in this mode all the following conditions must be met:...
Page 31
VLAN separation mode, all VLANs pass between the LAN and PC ports. However, the CPU port receives all traffic even on VLANs that are not equal to L2QVLAN. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 32
• 0: The phone continues to attempt a DHCP REQUEST forever. VLANTEST is configured through: • Settings file Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 33
Specifies the value of the 802.1Q VLAN ID that is used to identify network traffic going into and Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 34
Ethernet switches. LAN equipment can use LLDP to manage power and administer VLANs, DSCP, and 802.1p priority fields. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 35
Status TIA LLDP MED LLDP-MED Media Endpoint Discovery capabilities = 00-33 (Inventory, Capabilities Power-via-MDI, Network Policy, MED Caps). Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 36
• The value of USE_DHCP is 0 and the value of IPADD is not 0.0.0.0. • The current value of L2QVLAN was set by a TIA LLDP MED Network Policy TLV. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 37
This parameter cannot be used in an environment where both SIP phones and H.323 phones exist. TLSSRVR and Proprietary File HTTPSRVR Server TLV Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 38
Network Policy (Voice) TLV. TCP and UDP ports Avaya J100 Series IP Phones use different protocols, such as TCP, TLS, and UDP to communicate with other equipment in the network. Part of this communication identifies which TCP or UDP ports each piece of equipment uses to support each protocol and each task within the protocol.
Page 39
Any unused port number TLS/SSL packets specified otherwise transmitted by the HTTP client of the phone. Any unused port number Transmitted Syslog messages Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 40
Any unused port number Transmitted signaling protocol packets Configuration through DHCP Avaya J100 Series IP Phones connect to the DHCP server during the boot up. You can configure the DHCP server to provide the following information to the device: • IP address •...
Page 41
Note: Administer option 6 and option 15 appropriately with DNS servers and domain names respectively. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 42
Option 43 is processed only if the first code in the Option is 1 with a value of 6889. The value 6889 is an Avaya enterprise number. All values are interpreted as strings of ASCII characters that are accepted with or without a null termination character.
Page 43
• Comply with the DHCP standard by setting DHCPSTD to 1. • Continue to use its IP address after the DHCP lease expires by setting DHCPSTD to 0. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 44
You can set the values of site-specific configuration parameters through a DHCP option. The default DHCP option to set the site-specific configuration parameters is 242. You can also use any August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 45
Specifies the path to all file names used in HTTPS GET operations during initialization. The path name is prepended. The string can be from 0 to 127 characters long. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 46
Review the release notes and any Read Me files associated with a distribution package. Ensure that the Settings file is not cached in your browser. To do this, clear the browser cache before downloading the settings file from the Avaya support Web site, so that you don’t get an old version.
Page 47
Phone installation Software distribution package containing the files needed to operate the Avaya J100 Series IP Phones are packaged together in a ZIP format. You can download the package from the Avaya support website. SIP software distribution package contains: • One or more software files •...
Page 48
• To access the user login screen, press the Login softkey. • To access the Admin menu, press the Admin softkey and enter the admin menu password. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 49
Administering emergency network. It may be necessary to numbers make arrangements with the appropriate authorities to test this functionality. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Broadsoft Device Management With the Broadsoft Device Management feature, you can download device-specific configuration files from the BroadWorks server in Avaya J100 Series IP Phones.The phone does not require a third-party provisioning server and connects automatically to the Broadsoft server.
• Confirm password 5. Click Update. The system displays the login page. 6. To log out of the web UI, click Logout. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
2. In the navigation pane, click Date & Time. 3. In the SNTP area, configure the following: • SNTP Server: Type the SNTP server IP address . August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 53
- ddd represents a three-characters containing the English abbreviation for the day of the week. For example, Sun for Sunday, Mon for Monday. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
4. Click one of the following : • Save • Reset to Default • Help Related links Ethernet settings field descriptions on page 55 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Pass-through refers to the forwarding of EAPOL frames between the phone's Ethernet line interface and the secondary PC Ethernet interface. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 56
Signaling Priority (Layer 2) Specifies the Layer 2 priority value for signaling protocol messages. Valid priority values are 0 to 7. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 57
Specifies the status of the auto-MDIX Value Operation. The options are: • Enable • Disable Related links Configuring Ethernet settings on page 54 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
You can also type the password in this field. Note that the maximum length of a password is 63 characters. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 59
Specifies the default key for your WiFi network. You can select a default key from WEP key 1 to 4. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Configuring network settings Procedure 1. Log in to the web interface as an administrator. 2. In the navigation pane, click Network. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Specifies the type of the ICMP destination unreachable messages . The options are: • No • Limited Port Unreachable messages Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 62
Use custom certificate for Web Server Specifies whether to use the custom server certificate when the web interface is accessed using HTTPS. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Description HTTP Provisioning Server HTTP Server Address Specifies the IP address of the of the provisioning file server. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 64
PC. To import a language file from your local PC or any PC connected to the Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
4. Click one of the following: • Save • Reset to Default • Help Related links Settings field descriptions on page 66 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Hold Reminder Timer Specifies the number of seconds after which the phone plays the hold reminder tone . Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 67
Specifies whether network configuration can be modified by a user. The options are: • Do not Allow to Modify • Allow to Modify Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 68
• Match at least 4 rightmost digits Emergency Call Emergency Numbers Specifies the emergency contact number. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 69
• 3db below nominal • Nominal • 3db above nominal • 6db above nominal • 9db above nominal Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 70
Ringtone Style Specifies the style of classic ring tone to be used. The options are: • North America Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 71
Specifies the removal of the PSTN access prefix from the outgoing number outgoing number. The options are: • No • Yes Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
4. Click one of the following: • Save • Reset to Default • Help Related links Certificates field descriptions on page 73 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
• Use OCSP address configured first and then OCSP field of AIA extension of the certificate being checked Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 74
Specifies the functioning of the device when performing certificate request enrolment. The options are: • Poll SCEP server periodically in background Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
4. Click one of the following: • Save • Reset to Default • Help Related links SIP settings field descriptions on page 76 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
The options are: • Manual: To configure SIP proxy server manually by using the phone or the web interface. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 77
• Enable G.711u law Specifies whether the G.711u law codec is enabled. The options are: • Disable • Enable Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 78
RTCP packets to a remote peer or an RTCP monitoring server. The options are: • Yes • No The default value is No. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 79
The default value is 5004. RTP Port (range) Specifies the port range to be used by the following connections: • RTP Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
75 Debugging Procedure 1. Log in to the web interface as an administrator. 2. In the navigation pane, click Debugging. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
The options are: • Emergencies • Alerts • Critical • Errors Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 82
The options are: • Enable • Disable SSH Idle Timeout Specifies the time after which SSH is disabled. discuss Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 83
• Disable • Enable with payloads removed from RTP packets • Enable with payloads included in RTP packets Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 84
The options are: • Off • On The default value is Off. Related links Debugging on page 80 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
2. Retrieves and checks the J100Supgrade.txt file for device upgrade if required. 3. Retrieves the 46xxsettings.txt and MACADDR.txt files for customer-specific configurations. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
• HTTPSRVR with <"”> is the name of the parameter that removes the cached HTTP file server address. This redirects the phone to the cloud service provider’s file server. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Chapter 6: Security configurations Security overview SIP-based Avaya J100 Series IP Phones provides several updated security features. When the phone is in a locked state, a user can only receive calls or make emergency calls. User logs and data are protected with the user account.
The identity certificate must be provided and validated by the server to establish mutual authentication. Server must validate the identity certificate to establish a secure connection.. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
• Serial Number • Subject Name • Issuer Name • Validity Period:notBefore and notAfter dates • Thumbprint: Hash of the certificate August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
TLS session. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
If the value includes the string $MACADDR, that string will be replaced by the phones MAC address. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 92
SERIALNO. If the value contains $MACADDR, $MACADDR is replaced by the value of MACADDR without the colon separators. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
2. In the Access code field, enter the administration password. 3. Press Enter. 4. Select IP Configuration > Ethernet IPv4. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Specifies the IP address of the DNS server. The available format is nnn.nnn.nnn.nnn. SNTP server Specifies the time server settings. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
2. In the Access code field, enter the admin menu password. 3. Press Enter. 4. Use the Down Arrow to select Network interface. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
You can configure group identifier from the phone UI as a local administration process. Related links Setting the group identifier on page 97 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
• Avaya Environment: Specifies whether the available SIP Avaya environment is in effect. The two modes to detect the available environment are as follows: - Auto: Detects the Avaya environment automatically. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 99
Configuring SIP settings - No: Does not detect the Avaya environment and switches to a non-Aura mode. Note: Disable the Avaya Environment configuration from the 46xxsettings.txt file. • Reg. policy: Specifies the registration policy for SIP. The two modes are as follows: - Alternate: Supports registration to one of the active controllers.
2. In the Access code field, enter the admin menu password. 3. Press Enter. 4. Select View. 5. Press Back to return to the main menu. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
• DOT1X: To support 802.1X Pass-thru operation, set the parameter to zero or one. • DOT1XSTAT: To support supplicant operation, set the parameter to one or two. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
This procedure erases all static information, without any possibility of recovering the data. Procedure 1. Press Admin menu > Administration. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 103
This is applicable to the phones in 3PCC environment only. Note: Avaya J100 Series IP Phones parameters stored for a particular user are not reflected in other phones, for example, 9600 Series IP Deskphones, even if the SIP user is the same.
Calendar information is updated whenever the user log in to the phone. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
• 0: Not displayed • 1: Displayed EXCHANGE_SNOOZE_TIME Specifies the number of minutes in which a reminder must be Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 106
Exchange reminder is displayed. Value Operation: • 0: Tone not generated. • 1: Tone generated. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 107
Specifies whether the Calendar synchronizes with the Microsoft Exchange. Value operation: • 0: To disable synchronization. • 1: To enable synchronization. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Note: This parameter is supported when failed over from Aura SM to a non-Aura survivable server (excluding BSM). Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Voicemail The Voicemail feature is used to dial the configured voice mail number to receive a voice message. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
1. Log in to the web interface as an administrator. 2. In the navigation pane, click SIP. 3. In the Miscellaneous area, specify the number to access the voice mail in a non-Avaya environment. 4. Click one of the following: •...
Configuring Groups list by using the web interface About this task To configure the Groups list using the web interface, do the following steps: August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Office for storing user data. Note: If the value of this parameter is set to null, then the Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Contacts list Parameter name Default value Description addition, deletion, and modification of Contacts is disabled. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Chapter 9: Backup and restore Backup and restore process Avaya J100 Series IP Phones support the backup and restore of the user-specific data. The phone supports HTTP over TLS (HTTPS) for backup and restore. The following user-specific data are supported for backup and restore: •...
Page 115
• HTTP server returns the file to the phone. If the automatic restore process fails, the phone displays the following message: Retrieval Failed August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
For example, for user guides, click User Guides in the Content Type filter. The list displays the documents only from the selected category. 7. Click Enter. August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Avaya Mentor videos provide technical content on how to install, configure, and troubleshoot Avaya products. About this task Videos are available on the Avaya Support website, listed under the video document type, and on the Avaya-run channel on YouTube. Procedure •...
AGCHAND Specifies the status of Automatic Gain Control (AGC) for the handset. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 119
Valid values are 0 through 299. This parameter affects settings for AGC dynamic range and handset noise reduction thresholds. Always Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 120
Specifies if the script files are to be downloaded from an authenticated server over an HTTPS link. Value operation: • 0: Optional • 1: Mandatory Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 121
• Only jpeg format files are supported. • The maximum file size is 256 KB. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 122
Specifies the volume level at which the Avaya audio brand is played. Value Operation • 8: 9db above nominal • 7: 6db above nominal Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 123
Syslog message will be also generated. Valid values are from 90 to 730. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 124
CONFIG_SERVER Null Specifies the address of the Avaya configuration server. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 125
Used for network call progress tones. • For Argentina use keyword Argentina. • For Australia use keyword Australia. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 126
• 1: Delete any identity certificate that may be present. DES_BLOCK Specifies if DES discovery is allowed to be attempted during the boot process. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 127
Specifies if DHCP complies with the IETF RFC 2131 standard: • And immediately stops using an IP address if the lease expires Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 128
AST features are not available. • 0: The phone operates in a mode where AST features are not available. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 129
802.1X. Valid values are MD5, and TLS. DOT1XSTAT Specifies the 802.1X supplicant operating mode. Value Operation Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 130
Valid values are 0, 1, or 2. The default value is 1. DSTSTART 2SunMar2L Specifies when to apply the offset for daylight savings time. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 131
Avaya J129 IP Phone. ELD_SYSNUM Controls whether Enhanced Local Dialing algorithm will be applied for System Numbers-Busy Indicators and Auto Dials. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 132
ENABLE_CALL_LOG Species if call logging and associated menus are available on the phone. Value Operation • 0: No Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 133
Value Operation • 0: No • 1: Yes Setting this parameter to 1 can speed up call setup. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 134
Specifies whether the J100 phone can operate in 2 different modes with IP Office. The first mode allows native Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 135
Value Operation: • 0: No • 1: Yes Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 136
• 1: Audio debug recording is enabled. ENABLE_REDIAL Specifies if Redial softkey is available. Value Operation • 0: No Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 137
• 1: Emergency softkey is displayed without a confirmation screen. • 2: Emergency softkey is displayed with a confirmation screen. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 138
CM/AST-II . Valid values are 0 through 1000. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 139
Value of 0 means that this timer is disabled. FIPS_ENABLED Specifies whether the usage of FIPS-140 approved cryptography is enabled or not. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 140
0 through 12 (hours), followed by a colon (:), followed by 00 through 59 (minutes). GROUP Specifies specifically-designated groups of phones by using IF Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 141
Names might contain spaces, but if any do, the Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 142
SCEP server that is not on the enterprise network. Valid value can contain zero or one IP address in dotted decimal or DNS Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 143
IPV6STAT Specifies whether IPv6 will be supported or not. Value operation: • 0: IPv6 will not be supported. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 144
RTCP ). All other frames except those specified by the L2QSIG parameter are set to priority 0. Valid values are 0 through 7. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 145
Specifies the language files that must installed or downloaded to the phone. Filenames can be full URL, relative pathname, or filename. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 146
• 0: Emergency events are logged. • 1: Alert and Emergency events are logged. • 2: Critical, Alert and Emergency events are logged. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 147
H1xx SIP R1.0 and later; the default is ALL which implies all categories. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 148
Exchange, or locally, the contact name saved first is displayed. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 149
(MTU) size transmitted by the phone. Valid values are 1496 or 1500. Use 1496 for older Ethernet switches. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 150
ASCII characters. Note: / must used as a separator between components. Commas do not work with some servers Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 151
Value operation: • 0: Certificates are revoked and the TLS connection is closed. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 152
• 1: Checks the OCSP_URI and then the OCSP field of the Authority Information Access (AIA) extension of the certificate. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 153
(0-9, *, #). PHNIC Specifies the international access code For the United States, the value is 011. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 154
This is the number you press to make an outside call. Valid values are 0 to 2 dialable characters (0-9, *, #). Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 155
• 4: 100Mbps half-duplex • 5: 100Mbps full-duplex • 6: 1Gbps full-duplex, if supported by hardware, otherwise auto-negotiated Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 156
Available values are: • Null: (Default) Specifies that the PKCS#12 identity certificate download is disabled. • 0–255 characters. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 157
PROCSTAT Specifies an access code to access the admin menu procedures. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 158
• 9: No Repeat without user option. PROVIDE_LOGOUT Specifies if user can log out from the phone. Value Operation • 0: No Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 159
4: Packet loss is > 3% or round trip network delay is > 560ms or jitter compensation delay is > 120ms Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 160
• 7: The tone volume is 15dB below the transmit audio level. • 8: The tone volume is 10dB below the transmit audio level. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 161
RINGTONES Null Specifies a list of display names and file names or URLs for a custom ring Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 162
3611) is sent as part of the RTCP packets to remote peer or to RTCP monitoring server. Value Operations • 0: No Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 163
SCEP certificate request. Values can contain 0 to 32 ASCII characters (50 ASCII characters. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 164
• 1: End user can select and change the screen saver images from the settings menu. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 165
Specifies whether to display last extension after logout. Value Operation: • 0: To hide last extension after logout. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 166
Specifies if a conference call continues after the host hangs up. Value Operation: • 0: Drop all parties. • 1: Continue conference Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 167
2: Enabled and payloads are included in RTP packets 3: Controlled from CRAFT menu - Allows you to enable or diable of RTP Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 168
Set the IP address of the SLA Mon server in the aaa.bbb.ccc.ddd format to restrict the registration of agents only to that server. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 169
Specifies a security string that must be included in SNMP query messages for the query to be processed. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 170
1: One-way speaker (also called monitor) enabled. 2: Full (two-way) speakerphone enabled. SSH_ALLOWED Specifies if SSH is supported. Value Operation 0: Disabled Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 171
2: SES or PPM does not show a FS- phoneData FeatureName with a Feature Version of 2 in the response to the getHomeCapabilities request Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 172
TCP keep-alive (TCP ACK) message. Valid values are from 10 through 3600 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 173
Valid values are from 0 to 65535. TLSSRVR Specifies the HTTPS server address. Valid values can contain 0 to 255 ASCII characters, including commas. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 174
Valid values are 5 through 60. VLANSEPMODE Specifies whether VLAN separation is enabled or disabled. Value operation: • 0: Disabled • 1: Enabled Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 175
Specifies the file name or URL for a custom single-channel WAV file coded in ITU-T G.711 u-law or A-law PCM Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 176
Specifies whether HTTP access to the web server is enabled or disabled. Value operation: • 0: Web Server is not accessible through HTTP. Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
BA 8B 66 5A 1A Root CA 32.55.1 96 2D DE A1 45 .1.2.22 9D 2A 46 97 2F Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 178
8A C1 63 B1 42 20 79 D2 B9 1E DF BB 1F B6 51 A0 63 3E Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 179
8D 5E BB 86 CE 3A AC D6 12 0D 0E 7E 9E DB AE 7C 6E F2 94 A2 7D 4C Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 180
Root Class 3 TRUST bits 9 8:50 4.1.478 8C E9 86 25 B9 Root 34 09 2E EC 29 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 181
B2 28 A5 6E 3B A0 05 66 0B E8 34 7C 44 2C 97 62 98 02 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 182
10 B5 86 7A CA 00 00 00 E1 2C 78 EF 95 8F D4 F4 38 9F Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 183
24 5B 81 4.1.802 3A 4D 0D 67 DB 89 9B 35 18:59 0B EB B2 3E 37 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 184
9C 41 4A 17 D6 tion 1.3.6.1. 37 B7 A5 06 47 Authorit 4.1.232 E9 BC 75 23 22 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 185
93 30 B0 B7 81 - G3 BF EC 50 E5 4A 1B 35 AF 7F DD D5 01 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 186
49 F3 8A 16 30 Authority - Certifica 94 FD 64 29 D5 tion DA 43 Authorit y - G4 Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 187
71 0B 9C D9 87 Class 3 5E CA 7E 31 70 7A F3 E9 6D 52 2B BD Table continues… August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 188
12 1A C5 7F 4E 82 82 90 Authorit BF B8 60 E8 4B Related links Certificate management on page 88 August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 189
Option 43 codes ............password ..............Option configuration ............. checklist site-specific parameters ..........44 installing ................25 download and save the software ......... August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 190
..........87 IP configuring Overview 802.1Q ................94 Wi-Fi ................DNS server ..............gateway ................ HTTP server ..............HTTPS server ...............94 Parameters August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...
Page 191
........21 software ................web interface downloading and saving ..........debugging ..............81 specification without DES ................. hardware ............... support ................August 2018 Installing and Administering Avaya J100 series IP Phones in third-party call control setup Comments on this document? infodev@avaya.com...