Panasonic AJ-CX4000G Operating Instructions Manual page 207

Screen display
Camera image screen
[INVALID]
[Cannot record - Playlist capacity is
full.]
[Cannot copy - Playlist capacity is full.] The camera tried to copy to a memory card where
[Exceeds capacity. Please reselect.]
[Check the destination media.]
[LOAD NG]
[SAVE NG]
[DISCONNECT USB CABLE.]
[CARD LOCKED.]
[CANNOT SELECT MORE CLIPS.]
[SELECT THE CLIP TO BE
DELETED.]
[SELECT THE CLIPS TO COPY.]
[NO CARD.]
[REINSERT OR CHECK CARD
<SLOT 1>]/[REINSERT OR CHECK
CARD <SLOT 2>]/[REINSERT OR
CHECK CARD <SLOT 3>]
[CANNOT RECORD.]
[REC PAUSE INVALID]
[WRITE PROTECTED]
[ATW MODE]
[AWB PRESET ****K]
[AWB UNABLE]
[S.GAIN MODE]
[CHECK FILTER]
[LOW LIGHT]
Chapter 10 Maintenance — Warning system
Description
Operation is disabled.
The camera tried to record on a memory card where
the number of playlists for recording has reached the
maximum.
the number of playlists for recording has reached the
maximum.
The remaining recording capacity of the memory card for
the copy destination is insufficient.
An error has occurred on the memory card for the copy
destination while copying.
Loading of the scene file has failed.
Writing of the scene file has failed.
Due to an OS non-compatible error, five minutes has
elapsed until the service mode connection is established.
The camera tried to protect or delete a clip on a memory
card that has been locked.
The camera tried to copy a clip to the memory card that
has been locked.
It has tried to select more than 99 clips.
It has tried to delete a clip without choosing any.
It has tried to copy a clip without choosing any.
Copying was tried to be executed without inserting a
memory card into card slot.
It has tried to copy to an error card.
Cannot be recorded.
The camera tried to stop the next recording before the
previous recording finished writing to the memory card.
The write-protected switch on the memory card is set to
the Protect side or the LOCK side.
The camera tried to execute auto white balance while auto
tracking white balance function operated.
The camera tried to execute auto white balance when the
<WHITE BAL> switch is set to <PRST>.
The camera tried to execute auto white balance while
super gain function operated.
The <ND FILTER>/<CC FILTER> dial is not set correctly
at power on.
The camera tried to execute auto white balance when the
<CC FILTER> dial was not set correctly.
Brightness has dropped.
A message is displayed.
f Operate after the the operation becomes enabled.
A message is displayed.
f Replace the memory card or delete unnecessary clips.
A message is displayed.
f Replace the memory card or delete unnecessary clips.
A message is displayed.
f Select the clip to copy again, or secure enough space in
the remaining recording capacity on the memory card for
the copy destination.
A message is displayed.
f Confirm the memory card for the copy destination.
A message is displayed.
f Check the memory card.
A message is displayed.
f Check the memory card.
A message is displayed.
f Confirm if the OS in use is supported by the camera.
A message is displayed.
f Unlock the memory card.
A message is displayed.
f Execute the process such as copying by every 99 clips.
A message is displayed.
f Select a clip to be deleted.
A message is displayed.
f Select a clip to be copied.
A message is displayed.
f Insert a memory card into the card slot.
A message is displayed.
f Check the memory card.
A message is displayed.
f Perform recording after making it possible.
A message is displayed.
f Stop recording after writing to the memory card is
complete. Recording can be stopped after the message
that is displayed disappears.
A message is displayed.
f Insert a memory card with write access.
A message is displayed.
f Cancel the auto tracking white balance function and
execute auto white balance.
A message is displayed.
f Set the <WHITE BAL> switch to <A> or <B> and execute
auto white balance.
A message is displayed.
f Cancel the super gain function and execute auto white
balance.
A message is displayed.
f Correctly set the <ND FILTER>/<CC FILTER> dial.
f Correctly set the <CC FILTER> dial and execute auto
white balance.
A message is displayed.
f Adjust the brightness.
– 207 –
Behavior and cause