Menu Settings - Panasonic AJ-CX4000G Operating Instructions Manual

(Factory setting: [L/M/H])
[DS.GAIN OFF]
Selects a method to release digital super gain mode (accumulated gain).
[L/M/H]
[DS.GAIN]
(Factory setting: [DS.GAIN])
[D.ZOOM]
Selects the zoom ratio for when the USER button assigned with [D.ZOOM] is pressed.
The items that can be set are as follows.
f [×2], [×3], [×4], [ALL]
(Factory setting: [ALL])
[USER SW]
The function to be assign to the USER button can be set.
Following functions can be assigned.
f [INHIBIT], [DRS], [FBC], [S.GAIN], [ATW], [ATW LOCK], [Y GET], [D.ZOOM], [DS.GAIN], [S.IRIS], [I.OVR], [S.BLK], [B.GAMMA], [FOCUS ASSIST],
[C.TEMP], [PRE REC], [REC CHECK], [DEL LAST CLIP], [SLOT SEL], [REC SW], [WFM], [LCD/VF HDR], [LCD/VF DETAIL], [VF COLOR],
[INDICATOR SW], [LOAD SETUP FILE], [LCD BACKLIGHT], [CARD READER MODE], [STREAMING START]
For details, refer to "Assigning function to the USER buttons" (page 129).
[USER1]
[USER2]
[USER3]
[USER4]
[USER5]
[WHITE BALANCE MODE]
[FILTER INH]
Selects whether to hold or not hold the white balance memory (Ach and Bch) data for each CC filter.
[ON]
[OFF]
(Factory setting: [ON])
[SHOCKLESS AWB]
When the position of the <WHITE BAL> switch is changed, set the time until it transfers to the white balance condition at the changed position.
[FAST]
[NORMAL]
[SLOW1]
[SLOW2]
[SLOW3]
[OFF]
(Factory setting: [NORMAL])
[AWB AREA]
Selects the detection area to perform the auto adjustment of the white balance.
[25%]
[50%]
[90%]
(Factory setting: [25%])
[ATW]
Assigns the setting of the auto tracking white balance function to the <WHITE BAL> switch.
The items that can be set are as follows.
f [Ach], [Bch], [PRE], [OFF]
(Factory setting: [OFF])
Chapter 4 Operation — Menu settings
The digital super gain mode is released in following cases.
f When the <GAIN> switch setting is changed
f When the USER button assigned with [DS.GAIN] is pressed
The digital super gain mode is released only when the USER button assigned with [DS.GAIN] is pressed.
Sets the function to assign to the <USER 1> button.
(Factory setting: [FOCUS ASSIST])
Sets the function to assign to the <USER 2> button.
(Factory setting: [S.GAIN])
Sets the function to assign to the <USER 3> button.
(Factory setting: [DS.GAIN])
Sets the function to assign to the <USER 4> button.
(Factory setting: [Y GET])
Sets the function to assign to the <USER 5> button.
(Factory setting: [WFM])
Holds Ach and Bch memory data (two memories), regardless of the CC filter.
Holds Ach and Bch memory data (eight memories), for each CC filter.
Transfers to the white balance condition in approximately one second.
Transfers to the white balance condition in approximately two seconds.
Transfers to the white balance condition in approximately three seconds.
Transfers to the white balance condition in approximately ten seconds.
Transfers to the white balance condition in approximately 20 seconds.
Transfers immediately.
Detects 25% of the area near screen center.
Detects 50% of the area near screen center.
Detects 90% of the screen area.
– 64 –