Alert - Panasonic AJ-CX4000G Operating Instructions Manual

Alert

Screen display
Camera image screen
[SIMUL REC WARNING <SLOT 2>]/
[SIMUL REC WARNING <SLOT 3>]
[SIMUL REC WARNING <SLOT 2>]/
[SIMUL REC WARNING <SLOT 3>]
[FAN STOPPED]
[Non-supported card. <SLOT 1>]
[Insert expressP2 card.]
[ENCRYPTED CARD <SLOT 1>]/
[ENCRYPTED CARD <SLOT 2>]/
[ENCRYPTED CARD <SLOT 3>]
[REINSERT OR CHECK CARD
<SLOT 1>]/[REINSERT OR CHECK
CARD <SLOT 2>]/[REINSERT OR
CHECK CARD <SLOT 3>]
[FORMAT ERROR CARD <SLOT 1>]/
[FORMAT ERROR CARD <SLOT 2>]/
[FORMAT ERROR CARD <SLOT 3>]
[NOT SDXC CARD <SLOT 2>]/[NOT
SDXC CARD <SLOT 3>]
[INCOMPATIBLE CARD <SLOT 2>]/
[INCOMPATIBLE CARD <SLOT 3>]
[DIR NG CARD <SLOT 1>]/[DIR NG
CARD <SLOT 2>]/[DIR NG CARD
<SLOT 3>]
[RUN DOWN CARD <SLOT 1>]/
[RUN DOWN CARD <SLOT 2>]/[RUN
DOWN CARD <SLOT 3>]
[SD CARD <SLOT 2>]/[SD CARD
<SLOT 3>]
[SLOT1 CANNOT REC]
[microP2/SD SELECTED]
[SLOT2/3 CANNOT REC]
[expressP2 SELECTED]
[BACKUP BATT EMPTY]
Chapter 10 Maintenance — Warning system
Description
An error has occurred in one of the memory cards during
simultaneous recording.
Recording has been attempted while the number of clips
has exceeded the limit on one of the memory cards during
simultaneous recording.
The fan has stopped.
Card other than expressP2 card is inserted in the card slot
1.
P2 card formatted with encryption with CPS (Content
Protection System) password is inserted.
The memory card cannot be recognized properly because
a recording medium which is not supported has been
inserted or there is dirt on the terminal of the memory card.
A memory card with management information out of
specifications has been inserted.
A SDHC memory card that cannot record the MOV format
data or a 32 GB microP2 card is inserted when [FILE
FORMAT] is set to MOV format.
A memory card that may not be able to record due to slow
writing speed has been inserted.
A P2 card with inappropriate directory placement is
inserted when [FILE FORMAT] is set to P2 format.
A P2 card exceeding the specified number of overwrites is
inserted.
SD card is inserted when [FILE FORMAT] is set to P2
format.
A memory card is inserted in card slot 1 when the
[RECORDING] menu → [REC MEDIA] → [microP2/SD]
is set.
A memory card is inserted in card slot 2 or card slot 3 when
the [RECORDING] menu → [REC MEDIA] → [expressP2]
is set.
Voltage lowering of the backup battery for internal clock
was detected when the power is set to < j > (ON).
A message is displayed for approximately five seconds.
f Recording to the other memory card will continue.
A message is displayed for approximately five seconds.
f Recording to the other memory card will continue.
f [SIMUL REC WARNING <SLOT 2>] [<OVER MAX
NUM. OF CLIPS>]/[SIMUL REC WARNING <SLOT 3>]
[<OVER MAX NUM. OF CLIPS>] is displayed in the
message display area of the STATUS screen for the
mode check.
f Replace the memory card or delete unnecessary clips.
A message is displayed.
f The current operation will continue.
f Stop the use immediately when the fan has stopped and
alert is displayed, and consult the dealer.
f If the fan has stopped, temperature of the camera will
rise. Therefore, do not use the camera for a long period
of time. Use the tripod, etc., and do not touch the camera
directly.
A message is displayed for approximately five seconds.
f Insert an expressP2 card.
A message is displayed for approximately five seconds.
f The camera does not support the CPS function of the
P2 card. Insert a P2 card that is not formatted with
encryption with CPS password.
f Formatting P2 card, which was formatted with encryption
with CPS password, in the camera will enable P2 card to
be used as unencrypted card.
A message is displayed for approximately five seconds.
f Check the memory card that is inserted.
f Insert the memory card again if displayed when inserting
a memory card.
A message is displayed for approximately five seconds.
f Insert a memory card that can record.
A message is displayed for approximately five seconds.
f Insert a SDXC memory card or 64 GB microP2 card.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Use a memory card with sufficient writing speed.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Take a backup of the memory card immediately, and use
it again after formatting.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Replace the P2 card.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Recording to a P2 card is recommended.
A message is displayed for approximately five seconds.
f Set to the [RECORDING] menu → [REC MEDIA] →
[expressP2] when recording on the memory card inserted
in card slot 1.
A message is displayed for approximately five seconds.
f Set to the [RECORDING] menu → [REC MEDIA] →
[microP2/SD] when recording on the memory card
inserted in card slot 2 or card slot 3.
A message is displayed for approximately five seconds.
f The current operation will continue.
f Set the date/time again after charging the built-in battery.
– 205 –
Behavior and cause