Setting The Electronic Shutter; Shutter Mode; Setting The Shutter Mode/Shutter Speed; Setting Synchro Scan Mode - Panasonic AJ-CX4000G Operating Instructions Manual

Setting the electronic shutter

Shutter mode

The shutter modes available on the camera's electronic shutter and shutter speeds that can be selected are as follows.
f Using a fixed shutter speed
- When removing flicker caused by lighting
- When shooting fast-moving subjects clearly
f Using the synchro scan mode
- When shooting eliminating stripe patterns in the horizontal direction while shooting on the monitor screen
- When shooting moving subjects with special effects
f Using the half shutter speed
- When shooting with special effects such as films
[REC FORMAT]*
59.94p
59.94i
29.97p
23.98p
50.00p
50.00i
25.00p
* [REC FORMAT] indicates only frame rate. For example, [1080-59.94i/AVC-G50] is 59.94i, and [2160-29.97p/420LongGOP 100M] is 29.97p.

Setting the shutter mode/shutter speed

Switch the <SHUTTER> switch to set the shutter speed in the shutter mode.
The shutter speed in the synchro scan mode can be changed by the <SYNCHRO SCAN> button on the side.
The shutter speed selection range can be restricted or use of the synchro scan mode can be selected beforehand in each item in the [CAMERA] menu
→ [SHUTTER SPEED].
Once selected, the shutter speed is saved even after the camera is turned off.
1
Press the <SHUTTER> switch positioned at <OFF> towards <ON>.
[POSITION1] is enabled.
2
Press the <SHUTTER> switch from <ON> towards <SEL>, and repeat this operation until the desired shutter mode or shutter
speed is displayed on the viewfinder screen.
f If all shutter modes and shutter speeds are available, the display changes in the following order.
[POSITION1], [POSITION2], [POSITION3], [POSITION4], [POSITION5], [POSITION6], [SYNCHRO SCAN]
@
NOTE
t Whichever shutter mode the electronic shutter is used in, the higher the shutter speed, the lower the sensitivity of the camera becomes.
t When the aperture is in the automatic mode, it will increasingly open and the depth of focus will become shallower as the shutter speed is increased.
t Under lighting conditions using fluorescent lighting or other discharge tube, horizontal stripes might appear on screen. If this happens, this can be
improved by adjusting the shutter speed.
t A subject that quickly crosses the camera may appear distorted when shot. This is due to the method applied for reading the signals from the pickup
device (MOS sensor), and is not a malfunction.
t Shutter mode is disabled while the digital super gain function is active.
Viewfinder screen display for shutter
For details, refer to "Display of the viewfinder status" (page 141).

Setting synchro scan mode

Follow the steps below to operate.
1
Press the <SHUTTER> switch from the <ON> side towards the <SEL> side to set the camera to the synchro scan mode.
2
Press the <SYNCHRO SCAN> button to adjust the shutter speed.
The shutter speed display in the synchro scan mode can be switched between seconds and angle in the [SCENE FILE] menu → [SYNC SCAN
TYPE].
Chapter 5 Shooting — Setting the electronic shutter
Shutter speed Half shutter speed
[1/100], [1/120], [1/250],
[1/500], [1/1000],
[1/2000], [HALF]
[1/60], [1/120], [1/250],
[1/500], [1/1000],
[1/2000], [HALF]
Variable range of synchro scan mode
1/120 1/60.0 to 1/7200
1/60 1/30.0 to 1/7200
1/48 1/24.0 to 1/7200
1/100 1/50.0 to 1/7200
1/50 1/25.0 to 1/7200
– 126 –
3.0 deg to 360 deg
(in 0.5 deg steps)