Output Signals; Digital Outputs; Analog Output 1 - Vacon NX ACTIVE FRONT END II Applications Manual

Arfiff05 Standard AFE-II
6.4

Output signals

6.4.1 Digital Outputs

Code Parameter
P2.4.1.1 MCB Control (Close)
P2.4.1.2 MCB Control Open
P2.4.1.3 Ready
P2.4.1.4 Run
P2.4.1.5 Fault
P2.4.1.6 Fault,Inverted
P2.4.1.7 Warning
P2.4.1.8 DC Above Limit
P2.4.1.9 DC Charge
P2.4.1.10 Ready To Start
P2.4.1.11 FB Dig Input 1
P2.4.1.12 FB Dig 1 Input Par
P2.4.1.13 FB Dig Input 2
P2.4.1.14 FB Dig 2 Input Par
P2.4.1.15 FB Dig Input 3
P2.4.1.16 FB Dig 3 Input Par
P2.4.1.17 FB Dig Input 4
P2.4.1.18 FB Dig 4 Input Par
P2.4.1.19 FB Dig Input 5
P2.4.1.20 FB Dig 5 Input Par
Table 5-4. Digital outputs parameters

6.4.2 ANALOG OUTPUT 1

Code Parameter
P2.4.2.1 Iout 1 signal
P2.4.2.2 Iout Content
Iout Filter
P2.4.2.3
Time
P2.4.2.4 Iout Invert
P2.4.2.5 Iout Minimum
P2.4.2.6 Iout Scale
P2.4.2.7 Iout Offset
Table 1- 5, Output signals, G2.3.4
Local contacts: http://drives.danfoss.com/danfoss-drives/local-contacts/
Min Max Unit
B.2 B.2 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0.1 E.10 DigOUT:
0 10000 ID
0.1 E.10 DigOUT:
0 10000 ID
0.1 E.10 DigOUT:
0 10000 ID
0.1 E.10 DigOUT:
0 10000 ID
0.1 E.10 DigOUT:
0 10000 ID
Min Max Unit
0.1 E.10 AnOUT
0 4
0 10 s
0 1
0 1
10 1000 %
-100 100 %
Default ID
B.2 1218 Static if ID1219 < DigOUT:A.1
Pulse, if used also ID1218 is
0.1 1219
pulse control.
0.1 432
0.1 433
0.1 434
0.1 435
0.1 436
0.1 451
0.1 1668
0.1 1686
0.1 455
0 891
0.1 456
0 892
0.1 457
0 893
0.1 169
0 894
0.1 170
0 895
Default ID Note
A.1 464
0 = 4 mA
1 = DC-Link Voltage
307 2 = Current
3 = Power
4 = +- Power
1 308 0=No filtering
0=Not inverted
0 309
1=Inverted
0=0 mA
0 310
1=4 mA
Percentage
100 311 Defines
content is it maximum value
Add -1000 to 1000% to the
0 375
analogue output.
vacon • 31
Description
multiplier.
output when