Related Manuals for Vacon NXS/P
Summary of Contents for Vacon NXS/P
- Page 1 ® ac drives flange mounting kit for fr7-fr9 installation manual...
-
Page 2: Table Of Contents
2 • vacon Flange mounting kit FR7-FR9 Document code: DPD01880A Date: 5/12/2016 INDEX General ..........................3 Vacon Flange Mounting Kit contents .................. 4 Installation ......................... 6 FR7 ............................6 FR8 ............................8 FR9 ............................9 Mounting .......................... 10 Information sticker ......................11... -
Page 3: General
• 3 GENERAL Using the Vacon Flange Mounting Kit, you can mount your Vacon NX frequency converter through the cabinet wall so that the control unit of the drive remains inside the cabinet. The correct installation of the Flange Mounting Kit affects the IP protection class of the frequency converter. -
Page 4: Vacon Flange Mounting Kit Contents
4 • vacon Flange mounting kit FR7-FR9 VACON FLANGE MOUNTING KIT CONTENTS The contents of the Flange Mounting Kits for different frames are shown in the following pictures. FR7: Flange, top Screws (5*10 TF) Flange, bottom Screws (5*10 TX) Flange, side... - Page 5 • 5 FR8: 1 Flange, top 4 Screws (4*8) 2 Flange, bottom 5 Sealing tape 3 Flange, side FR9: 1 Flange, top 4 Screws (6*10) 2 Flange, bottom 5 Sealing tape 3 Flange, side 24-hour service +358-40-8371 150 • Email vacon@vacon.com...
-
Page 6: Installation
6 • vacon Flange mounting kit FR7-FR9 INSTALLATION These instructions guide you through the installation of the Flange Mounting Kit that you have purchased for your FR7, FR8 or FR9 size frequency converter. Note: The sealant to be used in the flange mounting kit installation is flame retardant silicone sealant (e.g. - Page 7 7. Seal the sides of the frequency 8. Seal the top flange. 9. Seal the small seams in each converter. corner. 10. Smoothen all sealed seams with your finger. Tip your finger in soap water before smoothening the seams. 24-hour service +358-40-8371 150 • Email vacon@vacon.com...
- Page 8 8 • vacon Flange mounting kit FR7-FR9 1. Remove these five screws from 2. Apply sealant to the right side flange. 3. Attach the right side flange with five the right side of the frequency screws (4x8 TF). converter. 4. Repeat the steps 1-3 with the left 5.
- Page 9 TF). (6x10 TF). 7. Fasten the sides of the bottom flange with two screws/side (6x10 TF). Seal all seams as shown in step 5. 24-hour service +358-40-8371 150 • Email vacon@vacon.com...
-
Page 10: Mounting
1. Make an opening in the cabinet door for the flange (collar) installation using the dimensions given in Vacon NX User's manual, chapter 5. 2. Attach the sealing tape around the opening. See Figure 1 for how to bend the tape at the corners... -
Page 11: Information Sticker
(1) and mark the installation date (2) on the sticker. Finally, attach the sticker on the drive. Dri ve m odified: Option board: NXOPT ....Date:....in slot: IP54 upgrade/ Collar Date:....EMC level modified: H to T / T to H Date:....24-hour service +358-40-8371 150 • Email vacon@vacon.com... - Page 12 Document ID: Vacon Ltd Member of the Danfoss Group Rev. A Runsorintie 7 65380 Vaasa Finland...