Analog Devices ADSP-BF526 EZ-Board Manual page 127

Evaluation system
Table of Contents

Advertisement

Index
PH0-15 programmable flags,
PJ0-3 programmable flags,
POST (power-on-self test) program, 1-17, 1-25,
1-37,
2-20
power
5V wall adaptor (P14), 1-3, 1-9, 1-30,
setup,
1-33
connector (P14), 1-9, 2-29,
down push buttons (SW16-17),
measurements,
1-36
power architecture, of this EZ-Board,
power saving features, of this EZ-Board,
PPI interface
connections,
1-20
expansion interface II connector (P3), 1-20,
2-4, 2-5, 2-8, 2-21,
product overview,
xiii
R
R274 JMP jumper (P23),
real-time clock (RTC) interface,
Reduced Instruction Set Computing (RISC),
reduced media independent interface (RMII),
1-21
reset
LED (LED7),
2-28
push button (SW18),
restrictions, of evaluation license,
rotary encoder
interface,
1-20
enable switch (SW13), 1-20,
switch (SW5),
2-11
RS-232 connector (J2),
RST/ETH LED jumper (JP11), 1-35,
RTS signal,
1-25
S
schematic, of ADSP-BF526 EZ-Board,
SCL signal,
1-30
I-4
2-6
2-8
2-29
2-35
2-15
1-30
1-35
2-33
2-26
1-26
xi
2-16
1-13
2-14
2-31
2-22
B-1
ADSP-BF526 EZ-Board Evaluation System Manual
SDA signal,
1-30
SDRAM interface, 1-16,
SENSE2 select jumper (JP10),
serial peripheral interconnect (SPI) ports, See
SPI interface
SPI interface
flash CS switch (SW3),
SPISEL1 signal,
1-19
SPORT0A enable switches (SW2, SW7), 1-22,
2-11
SPORT1 enable switch (SW21),
SRAM memory
connections,
1-14
power jumper (P19),
standalone debug agent, xii, 1-9, 1-10, 1-13,
1-16,
1-28
startup, of this EZ-Board
CCES,
1-5
SW10 (mic select) switch, 1-23,
SW11 (Ethernet mode) switch, 1-21,
SW12 (Ethernet enable) switch, 1-18, 1-21,
2-14
SW13 (rotary/NAND) switch, 1-20,
SW14 (UART1 setup) switch, 1-25,
SW15 (IO) push button,
SW16-17 (power down) push buttons,
SW18 (reset) push button,
SW19 (IO) push button,
SW1 (boot mode select) switch, 1-18, 1-20,
2-10
SW20 (push button enable) switch, 1-24, 1-27,
2-15, 2-16,
2-24
SW21 (SPORT1 enable) switch,
SW22 (battery) switch, 1-9, 2-18,
SW2 (SPORT0 enable) switch, 1-22,
SW3 (SPI flash CS) switch,
SW5 (rotary encoder) switch,
SW6 (flash enable) switch,
SW7,
1-22
SW7 (SPORT0 enable) switch, 1-22,
1-30
2-22
1-18
2-18
1-36
2-13
2-13
2-14
2-15
2-15
2-15
2-16
2-15
2-18
2-28
2-11
1-18
2-11
2-12
2-11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADSP-BF526 EZ-Board and is the answer not in the manual?

Questions and answers

Table of Contents