Analog Devices ADSP-BF518F EZ-Board Manual
  1. Manuals
  2. Brands
  3. Analog Devices Manuals
  4. Motherboard
  5. ADSP-BF518F EZ-Board
  6. Manual

Analog Devices ADSP-BF518F EZ-Board Manual

Evaluation system
Hide thumbs Also See for ADSP-BF518F EZ-Board:
Table of Contents

Advertisement

Quick Links

Download this manual
ADSP-BF518F EZ-Board
®
Evaluation System Manual
Revision 1.3, July 2012
Part Number
82-000217-01
Analog Devices, Inc.
a
One Technology Way
Norwood, Mass. 02062-9106

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADSP-BF518F EZ-Board and is the answer not in the manual?

Questions and answers

Related Manuals for Analog Devices ADSP-BF518F EZ-Board

Summary of Contents for Analog Devices ADSP-BF518F EZ-Board

  • Page 1 ADSP-BF518F EZ-Board ® Evaluation System Manual Revision 1.3, July 2012 Part Number 82-000217-01 Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106...
  • Page 2 Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use;...
  • Page 3 Regulatory Compliance The ADSP-BF518F EZ-Board is designed to be used solely in a laboratory environment. The board is not intended for use as a consumer end prod- uct or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity.

  • Page 5: Table Of Contents

    What’s New in This Manual ............xvii Technical Support ............... xvii Supported Processors ..............xviii Product Information ..............xix Analog Devices Web Site ............xix EngineerZone ................. xix Related Documents ..............xx Notation Conventions ..............xxi USING THE ADSP-BF518F EZ-BOARD Package Contents ................
  • Page 6 UART Interface ................1-23 RTC Interface ................1-24 LEDs and Push Buttons .............. 1-24 JTAG Interface ................1-25 Land Grid Array ................. 1-26 Expansion Interface II ..............1-26 Power Measurements ..............1-27 Power-On-Self Test ..............1-28 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 7 Programmable Flag Push Buttons (SW12–13) ......2-12 Rotary Encoder with Momentary Switch (SW14) ....2-12 SPORT0 ENBL Switch (SW15) ..........2-12 Encoder Enable Switch (SW19) ..........2-13 eMMC Enable Switch (SW20–21) ......... 2-13 ADC Loopback Switches (SW22–23) ........2-13 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 8 Expansion Interface II Connector (J1) ........2-21 RS-232 Connector (J2) ............2-21 Power Connector (J3) ............2-21 Dual Audio Connectors (J4–5) ..........2-22 Battery Holder (J12) ............. 2-22 SD Connector (J13) .............. 2-22 Ethernet Connector (J14) ............2-22 viii ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 9 Expansion Interface II Connectors (P2 and P4) ...... 2-24 Expansion Interface II Connector (P3) ........2-24 DMAX Land Grid Array Connectors (P5–7) ......2-25 Standalone Debug Agent Connector (ZP1) ......2-25 ADSP-BF518F EZ-BOARD BILL OF MATERIALS ADSP-BF518F EZ-BOARD SCHEMATIC INDEX ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 10 Contents ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 11 PREFACE ® Thank you for purchasing the ADSP-BF518F EZ-Board , Analog ® Devices, Inc. evaluation system for Blackfin processors. Blackfin processors embody a type of embedded processor designed specif- ically to meet the computational demands and power constraints of today’s embedded audio, video, and communications applications. They deliver breakthrough signal-processing performance and power efficiency within a reduced instruction set computing (RISC) programming model.
  • Page 12 Analog Devices JTAG emulators offer faster communication between the host PC and target hardware. To learn more about Analog Devices emulators and processor development tools, go to http://www.analog.com/dsp/tools The ADSP-BF518F EZ-Board provides example programs to demonstrate the capabilities of the product.

  • Page 13: Preface

    • 25 MHz crystal • Programmable VDDINT core power • Analog Devices AD5258 TWI digital potentiometer • Analog Devices ADP1715 low dropout linear regulator • Synchronous dynamic random access memory (SDRAM) • Micron MT48LC32M16A2TG – 64 MB (32M x 16-bits) •...
  • Page 14 • Ethernet interface • National Semiconductor DP83848 PHY device • 10-BaseT and 100-BaseTX • Auto-MDIX • ADC interface • Analog Devices AD7266 2 MSPS, 12-bit, 3-channel SAR analog-to-digital converter • Thumbwheel • Panasonic EVQ-WKA001 rotary encoder • Universal asynchronous receiver/transmitter (UART) •...

  • Page 15: Purpose Of This Manual

    (board). The text describes operation and configuration of the board components and provides guide- lines for running your own code on the ADSP-BF518F EZ-Board. Finally, a schematic and a bill of materials are provided for reference.

  • Page 16: Intended Audience

    Intended Audience Intended Audience The primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture and instruction set. Programmers who are unfamiliar with Analog Devices processors can use this manual, but should supplement it with other texts that describe your target architecture.

  • Page 17: What's New In This Manual

    Materials”. • Modifications and corrections based on errata reports against the previous manual revision have been made. For the latest version of this manual, please refer to the Analog Devices Web site. Technical Support You can reach Analog Devices processors and DSP technical support in the following ways: •...

  • Page 18: Supported Processors

    • E-mail your questions about processors and processor applications processor.support@analog.com (Greater China support) processor.china@analog.com • In the USA only, call 1-800-ANALOGD (1-800-262-5643) • Contact your Analog Devices sales office or authorized distributor. Locate one at: www.analog.com/adi-sales • Send questions by mail to: Processors and DSP Technical Support Analog Devices, Inc.

  • Page 19: Product Information

    Preface Product Information Product information can be obtained from the Analog Devices Web site and the online help system. Analog Devices Web Site The Analog Devices Web site, , provides information www.analog.com about a broad range of products—analog integrated circuits, amplifiers, converters, and digital signal processors.

  • Page 20: Related Documents

    ADSP-BF518(F) Blackfin Embedded Processor Data Sheet ADSP-BF51x Blackfin Processor Hardware Description of internal processor architecture Reference and all register functions Description of all allowed processor assembly Blackfin Processor Programming Reference instructions ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 21: Notation Conventions

    A Warning identifies conditions or inappropriate usage of the product that could lead to conditions that are potentially hazardous for the devices users. In the online version of this book, the word Warning appears instead of this symbol. ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 22 Notation Conventions xxii ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 23: Using The Adsp-Bf518F Ez-Board

    1 USING THE ADSP-BF518F EZ-BOARD This chapter provides information to assist you with development of pro- grams for the ADSP-BF518F EZ-Board evaluation system. The following topics are covered. • “Package Contents” on page 1-3 • “Default Configuration” on page 1-3 •...
  • Page 24 For information about the graphical user interface, including the boot loading, target options, and other facilities of the EZ-Board system, refer to the online help. For more information about the ADSP-BF518F Blackfin processor, see documents referred to at “Related Documents”. ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 25: Package Contents

    Store the unused EZ-Board in the protective shipping package. The ADSP-BF518F EZ-Board board is designed to run outside your per- sonal computer as a standalone unit. You do not have to open your computer case.
  • Page 26 Default Configuration connector locations, and LEDs used in installation. Confirm that your board is in the default configuration before using the board. Figure 1-1. Default EZ-Board Hardware Setup ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 27: Cces Install And Session Startup

    Follow these instructions to ensure correct operation of the product soft- ware and hardware. Step 1: Connect the EZ-KIT Lite board to a personal computer (PC) run- ning CCES using one of two options: an Analog Devices emulator or via the debug agent. Using an Emulator: 1.

  • Page 28: Session Startup

    Note: If you connect the board or emulator first (before installing CCES) to the PC, the Windows driver wizard may not find the board drivers. 1. Navigate to the CCES environment via the Start menu. Note that CCES is not connected to the target board. ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 29 The Select Connection Type page of the Session Wizard appears. 5. Select one of the following: • For standalone debug agent connections, EZ-Board and click Next. • For emulator connections, Emulator and click Next. The Select Platform page of the Session Wizard appears. ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 30 CCES Install and Session Startup 6. Do one of the following: • For standalone debug agent connections, ensure that the selected platform is ADSP-BF518F EZ-Board via Debug Agent. • For emulator connections, choose the type of emulator that is connected to the board.

  • Page 31: Visualdsp++ Install And Session Startup

    (PC) running VisualDSP++: via an Analog Devices emulator or via a standalone debug agent module. The standalone debug agent allows a debug agent to interface to the ADSP-BF518F EZ-Board. The stand- alone debug agent is shipped with the kit.

  • Page 32: Session Startup

    5. The Select Platform page of the wizard appears on the screen. For standalone debug agent connections, ensure that the selected platform is ADSP-BF518F EZ-Board via Debug Agent. For emu- lator connections, choose the type of emulator that is connected.

  • Page 33: Cces Evaluation License

    Delete. Click OK. CCES Evaluation License The ADSP-BF518F EZ-Board software is part of the Board Support Pack- age (BSP) for the Blackfin ADSP-BF51x family. The EZ-Board is a licensed product that offers an unrestricted evaluation license for 90 days after activation.

  • Page 34: Visualdsp++ Evaluation License

    • Analog Devices directly. Call (800) 262-5645 or 781-937-2384 or go to: http://www.analog.com/buyonline • Analog Devices, Inc. local sales office or authorized distributor. To locate one, go to: http://www.analog.com/salesdir/continent.asp  The EZ-Board hardware must be connected and powered up to use CCES with a valid evaluation or full license.

  • Page 35: Lockbox Key Security Features

    Table 1-1. The inter- nal memory details can be found in the ADSP-BF51x Blackfin Processor Hardware Reference. The ADSP-BF518F EZ-Board includes four types of external memory: synchronous dynamic random access memory (SDRAM), serial peripheral ADSP-BF518F EZ-Board Evaluation System Manual 1-13...
  • Page 36 CORE MMR REGISTERS 0xFFE0 0000 Table 1-2. EZ-Board External Memory Map Start Address End Address Content SDRAM (SDRAM) 0x0000 0000 0x03FF FFFF Reserved 0x0800 0000 0x1FFF FFFF ASYNC memory bank 0 (flash) 0x2000 0000 0x200F FFFF 1-14 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 37: Sdram Interface

    For more information on changing the reset values, refer to the online help. An example program is included in the EZ-Board installation directory to demonstrate how to setup and access the SDRAM interface. For more ADSP-BF518F EZ-Board Evaluation System Manual 1-15...

  • Page 38: Parallel Flash Memory Interface

    “reset values”. Parallel Flash Memory Interface The parallel flash memory interface of the ADSP-BF518F EZ-Board con- tains a 4 MB (2M x 16 bits) Numonyx M29W320EB chip. Flash memory connects to the 16-bit data bus and address lines 1 through 19. Chip...

  • Page 39: Sd Interface

    SD interface. SPI Interface The ADSP-BF518F processor has two serial peripheral interface (SPI) ports with multiple chip select lines. The SPI0 port connects directly to serial flash memory and expansion interface II. ADSP-BF518F EZ-Board Evaluation System Manual 1-17...
  • Page 40 EZ-Board installation directory, and U-Boot documentation. U-Boot includes an SPI flash driver and can be used to download a new file over Ethernet or serial connection, and write the file to SPI flash. 1-18 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 41: Parallel Peripheral Interface (Ppi)

    The three-wire rotary encoder interface connects to the thumbwheel rotary switch ( ) and expansion interface II. The SW19 rotary encoder can be turned clockwise for the up function, counter ADSP-BF518F EZ-Board Evaluation System Manual 1-19...

  • Page 42: Ethernet Interface

    The PHY can be put into iso- late mode by installing . The isolate mode should be used whenever JP18 the PHY is not used, and another PHY is connected to one of the MII 1-20 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 43: Audio Interface

    The control interface of the codec is via a 2-wire interface (TWI). Mic gain values of 14 dB, 0 dB, or –6 dB are selectable through switch For more information, see “MIC Gain/Loopback Switch (SW5)” on page 2-10. ADSP-BF518F EZ-Board Evaluation System Manual 1-21...

  • Page 44: Adc Interface

    The ADC connects to the ADSP-BF518F processor via the processor’s serial port 1. is disconnected from the ADC by turning switch SPORT1 , which enables for the expansion interface II or for the SPORT1 1-22 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 45: Uart Interface

    The ADSP-BF518F processor has two built-in universal asynchronous receiver transmitters (UARTs). share the processor’s pins with UART0—1 other peripherals on the EZ-Board. has full RS-232 functionality via the Analog Devices 3.3V UART0 ADM3202 line driver and receiver ( ). When using , do not set...

  • Page 46: Rtc Interface

    The three LEDs, labeled through , are accessed via the LED1 LED3 pins of the processor (respectively). For information on how to program the flag pins, refer to the ADSP-BF51x Blackfin Processor Hard- ware Reference. 1-24 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 47: Jtag Interface

    The standalone debug agent can be removed, and an external emulator can be attached to the EZ-Board. Be careful not to damage the connectors when removing the debug agent. The emulator connects to on the back ADSP-BF518F EZ-Board Evaluation System Manual 1-25...

  • Page 48: Land Grid Array

    “CCES Install and Session Startup” on page 1-5 “VisualDSP++ Install and Session Startup” on page 1-9 for more information. For more information about emulators, contact Analog Devices or go to: http://www.analog.com/processors/tools/blackfin Land Grid Array The ADSP-BF518F EZ-Board has provisions for probing every port pin and the EBIU interface of the processor on connectors .

  • Page 49: Power Measurements

    Additional circuitry can add extra loading to signals, decreasing their maximum effective speed.  Analog Devices does not support and is not responsible for the effects of additional circuitry. Power Measurements Several locations are provided for measuring the current draw from vari- ous power planes.

  • Page 50: Power-On-Self Test

    Board Design Database file containing all of the electronic information required for the .zip design, layout, fabrication and assembly of the product is available for download from the Analog Devices board design database at: http://www.analog.com/board-design-database 1-28 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 51: Adsp-Bf518F Ez-Board Hardware Reference

    EZ-Board board. The following topics are covered. • “System Architecture” on page 2-2 Describes the ADSP-BF518F EZ-Board configuration and explains how the board components interface with the processor. • “Programmable Flags” on page 2-3 Shows the locations and describes the programming flags (PFs).

  • Page 52: System Architecture

    This EZ-Board is designed to demonstrate the ADSP-BF518F Blackfin processor capabilities. The processor has an I/O voltage of 3.3V. The core voltage of the processor is controlled by an Analog Devices ADP1715 low dropout regulator (LDO) and an Analog Devices AD5258 digipot, which...

  • Page 53: Programmable Flags

    ETxD2/PPID0/SPI1_SSEL2/TACLK6 ETXD2 Land grid array, expansion interface II Default: ERxD2/PPID1/PWM_AH/TACLK7 ERXD2 Land grid array, expansion interface II Default: ETxD3/PPID2/PWM_AL ETXD3 Land grid array, expansion interface II Default: ERxD3/PPID3/PWM_BH/TACLK0 ERXD3 Land grid array, expansion interface II ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 54 Land grid array, expansion interface II Default: PF13 ERxD1/PPID13/PWM_BH ERXD1 Land grid array, expansion interface II Default: PF14 ETxEN/PPID14/PWM_BL ETXEN Land grid array, expansion interface II Default: PF15 RMII_PHYINT/PPID15/PWM_SYNC RMII_PHYINT Land grid array, expansion interface II ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 55 Land grid array, expansion interface II Default: PG11 SPI0_SS/AMS[2]/SPI1_SSEL5/ AMS2 Land grid array, expansion interface II TACLK2 Default: PG12 SPI0_SCK/PPICLK_2/TMRCLK SPI0_SCK Land grid array, expansion interface II Default: PG13 SPI0_MISO/TMR0/PPIFS1_2 SPI0_MISO Land grid array, expansion interface II ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 56 Default: TSCLK1/ARDY/ECLK/CDG LED2 , land grid array, expansion ADC_A1 interface II Default: DT1SEC/UART1_TX/ LED3 , land grid array, expansion SPI1_SSEL1/CZM ADC_A2 interface II Default: not used DR1SEC/UART1_RX/TMR7/TACI2 , land grid array, expansion interface II DR1SEC ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 57: Push Button And Switch Settings

    ADSP-BF518F EZ-Board Hardware Reference Push Button and Switch Settings This section describes operation of the push buttons and switches. The push button and switch locations are shown in Figure 2-2. Figure 2-2. Push Button and Switch Locations ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 58: Boot Mode Select Switch (Sw1)

    Boot from 8- or 16-bit external flash memory (default) Boot from internal SPI memory Boot from external SPI memory (EEPROM or flash) Boot from SPI0 host Boot from OTP memory Boot from SDRAM Boot from host UART0 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 59: Pb Enable Switch (Sw2)

    SPI flash. When using the external SPI SPI0_SEL2 flash, the available size for parallel flash is 3 MB. Table 2-6. Flash Enable Switch (SW3) SW3 Switch Position (Default) Processor Signal AMS0 AMS1 AMS2 AMS3 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 60: Sport1 Enable Switch (Sw4)

    “Audio Interface” on page 1-21 for more information about the audio codec. Table 2-7. MIC Gain Switch (SW5) Gain SW5 Switch Settings 5 (14 dB) 1 (0 dB) 0.5 (–6 dB) OFF, OFF, ON, OFF (default) Unused 2-10 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 61: Uart Setup Switch (Sw10)

    PC is initialized, pushing a reset button does not reset the USB chip on the debug agent. The only way to reset the USB chip on the debug agent is to power down the EZ-Board. ADSP-BF518F EZ-Board Evaluation System Manual 2-11...

  • Page 62: Programmable Flag Push Buttons (Sw12-13)

    7 and 8 are used SW15 to disconnect the TWI bus from the codec. When the interface is SPORT0 used on the expansion interface II, set . By default, is set SW15 SW15 to all 2-12 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 63: Encoder Enable Switch (Sw19)

    ADC Loopback Switches (SW22–23) The ADC loopback switches ( ) are used for testing only. SW22 SW23 The switches are used to send an analog signal generated from the codec to the ADC circuit for evaluation. ADSP-BF518F EZ-Board Evaluation System Manual 2-13...

  • Page 64: Jumpers

    Jumpers Jumpers This section describes functionality of the configuration jumpers. Figure 2-3 shows the jumper locations. Figure 2-3. Configuration Jumper Locations 2-14 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 65: Flash Wp Jumper (Jp3)

    Block 70 contains 64 KB of configuration data at address range . When the jumper is installed on 0x203 F0000—0x203 FFFFF and the parallel flash driver from Analog Devices is used, block 70 is read-only. By default, is installed. OTP Flag Enable Jumper (JP14)

  • Page 66: Mic Select Jumper (Jp15)

    By default, , and the power flows through the two-pin IDC header. To measure power, remove the jumper and measure voltage across the 0.1 ohm resistor. Once voltage is 2-16 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 67: Vddext Power Jumper (P9)

    IDC header. To measure power, remove the jumper on and measure voltage across the 0.1 ohm resistor. Once voltage is measured, power can be calculated. For more information, refer “Power Measurements” on page 1-27. ADSP-BF518F EZ-Board Evaluation System Manual 2-17...

  • Page 68: Leds

    LEDs LEDs This section describes the on-board LEDs. Figure 2-4 shows the LED locations. Figure 2-4. LED Locations 2-18 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 69: Gpio Leds (Led1-3)

    When is lit, it indicates that the master reset of all major ICs is LED9 active. The reset LED is controlled by the Analog Devices ADM708 supervisory reset circuit. You can assert the reset push button ( ) to SW11 assert a master reset and activate For more information, see “Reset...

  • Page 70: Connectors

    This section describes connector functionality and provides information about mating connectors. See connector locations in Figure 2-5. Connectors shown with a dotted line are on the backside of the PCB Figure 2-5. Connector Locations 2-20 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 71: Expansion Interface Ii Connector (J1)

    ) provides all of the power necessary to operate the EZ-Board. Part Description Manufacturer Part Number 0.65 mm power jack 045-0883R Mating Power Supply (shipped with the EZ-Board) 5.0VDC@2.5A power supply CUI STACK DMS050260-P12P-SZ ADSP-BF518F EZ-Board Evaluation System Manual 2-21...

  • Page 72: Dual Audio Connectors (J4-5)

    Mating Memory Card (shipped with the EZ-Board) 256 MB SANDISK STACK SDSDB-256-A10 Ethernet Connector (J14) Part Description Manufacturer Part Number RJ-45 Ethernet jack STEWART SS-6488-NF Mating Cable (shipped with the EZ-Board) Cat 5E patch cable RANDOM PC10/100T-007 2-22 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 73: Mii Connector (J15)

    When using an emulator with the EZ-Board, the standalone debug agent must be removed. Follow the installation instructions provided in “CCES Install and Session Startup” on page 1-5 “VisualDSP++ Install and Ses- sion Startup” on page 1-9, using as the JTAG connection point. ADSP-BF518F EZ-Board Evaluation System Manual 2-23...

  • Page 74: Expansion Interface Ii Connectors (P2 And P4)

    “Expansion Interface II” on page 1-26. For availability and pricing of the connector, contact Samtec. Part Description Manufacturer Part Number 70-position 0.1”, SMT header SAMTEC TSSH-135-01-L-DV-A Mating Connector 70-position 0.1”, SMT socket SAMTEC SSW-135-22-F-D-VS 2-24 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 75: Dmax Land Grid Array Connectors (P5-7)

    EZ-Board. The standalone debug agent requires both the connectors. For more informa- tion, see “CCES Install and Session Startup” on page 1-5 “VisualDSP++ Install and Session Startup” on page 1-9. ADSP-BF518F EZ-Board Evaluation System Manual 2-25...
  • Page 76 Connectors 2-26 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 77 SOIC14 IDT74FCT3244 IDT74FCT3244APYG APY SSOP20 32.768KHZ EPSON MC-156 OSC008 32.7680KA-A0:ROHS 25MHZ OSC003 EPSON SG-8002CA MP SN74LVC1G08 U23-U26 SN74LVC1G08DBVR SOT23-5 MT48LC32M16 MICRON MT48LC32M16A2P-75 A2TG-75 TSOP54 SI4411DY SO-8 VISHAY Si4411DY-T1-E3 12MHZ OSC003 EPSON SG-8002CA-MP SN74AUC1G00 SN74AUC1G00DBVR SOT23-5 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 78 ADSP-BF518F ANALOG ADSP-BF518BSWZ-4F4 LQFP176 DEVICES ADP1864AUJZ ANALOG ADP1864AUJZ-R7 SOT23-6 DEVICES ADP1611 ANALOG ADP1611ARMZ-R7 MSOP8 DEVICES ADP1715 ANALOG ADP1715ARMZ-R7 MSOP8 DEVICES ADP1710 ANALOG ADP1710AUJZ-R7 TSOT5 DEVICES ADR550B ANALOG ADR550BRTZ-REEL7 SOT23-3 DEVICES AD5258 ANALOG AD5258BRMZ10 MSOP10 DEVICES ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 79: Adsp-Bf518F Ez-Board Bill Of Materials

    ADSP-BF518F EZ-Board Bill Of Materials Ref. Description Reference Manufacturer Part Number Designator ADP1715 ANALOG ADP1715ARMZ-1.8-R7 MSOP8 DEVICES AD8022 MSOP8 U29-U34 ANALOG AD8022ARMZ DEVICES AD7266BCPZ ANALOG AD7266BCPZ LFCSP32 DEVICES ADP1610 ANALOG ADP1610ARMZ-R7 MSOP8 DEVICES SSM2603 ICS009 ANALOG SSM2603CPZ-R2 DEVICES DIP8 SWT016 SW15,SW20 C&K...
  • Page 80 EVQ-Q2K03W SWT024 ROTARY_ENC_ SW14 PANASONIC EVQ-WKA001 EDGE SWT025 QMS 52x2 SAMTEC QMS-052-06.75-L-D-A QMS52x2_SMT IDC 25x2 P2,P4 SAMTEC TSSH-125-01-L-DV-A IDC25x2_SMTA IDC 35x2 SAMTEC TSSH-135-01-L-DV-A IDC35x2_SMTA IDC 7x2 SAMTEC TSM-107-01-T-DV-A IDC7x2_SMTA BATT_HOLDER MEMORY BH600 16MM PROTECTI BATT_COIN16 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 81 ADSP-BF518F EZ-Board Bill Of Materials Ref. Description Reference Manufacturer Part Number Designator IDC 2X1 JP16 SAMTEC TSM-102-01-T-SV IDC2X1_SMT ROTARY COPAL S-8110 SWT027 RJ45 W/LEDS PULSE ENG. J0011D21BNL CON065 IDC 18X2 SAMTEC TSM-118-01-T-DV IDC18X2_M_S YELLOW LED1-LED3 DIGI-KEY P512TR-ND LED001 100 1/10W 5%...
  • Page 82 0.1UF 10V 10% C4-C6,C9, 0402ZD104KAT2A 0402 C11-C14,C25, C39,C42-C45, C47-C48, C62-C63,C65, C72,C76, C86-C87,C89, C115-C118, C140,C152, C188-C194, C211-C220, C222 0.01UF 16V 10% C1,C8,C17-C24, 0402YC103KAT2A 0402 C26-C36,C38, C46,C49-C58, C73,C119-C122, C139,C154, C179-C187, C223-C225 10K 1/16W 5% R246 VISHAY CRCW040210K0FKED 0402 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 83 ADSP-BF518F EZ-Board Bill Of Materials Ref. Description Reference Manufacturer Part Number Designator 10K 1/16W 5% R1,R11, VISHAY CRCW040210K0FKED 0402 R18-R21,R26, R59,R143-R145, R152, R154-R156, R161-R164, R168,R173, R203,R245, R268,R270, R356-R370, R382,R390 4.7K 1/16W 5% R6-R8,R13-R17, VISHAY CRCW04024K70JNED 0402 R269 0 1/16W 5%...
  • Page 84 0603 C141 470PF 50V 5% C143 06033A471JAT2A 0603 220UF 6.3V 20% CT3-CT4,CT6 SANYO 10TPE220ML 10M 1/10W 5% VISHAY CRCW060310M0FNEA 0603 330 1/10W 5% R153,R157-R160 DIG01 541-330GTR-ND 0603 0.0 1/10W 1% R52-R53,R195, PHYCOMP 232270296001L 0603 R346 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 85 ADSP-BF518F EZ-Board Bill Of Materials Ref. Description Reference Manufacturer Part Number Designator 0.0 1/10W 1% R345,R351 PHYCOMP 232270296001L 0603 49.9 1/16W 1% R68,R71-R77, VISHAY CRCW060349R9FNEA 0603 R79-R84, R371-R374 10 1/10W 5% R166,R169, VISHAY CRCW060310R0JNEA 0603 R207-R208, R213,R216, R219-R220, R223,R226, R229,R234, R237,R240,R349 10.0K 1/10W 1%...
  • Page 86 PANASONIC LN1361CTR RED LED001 LED9 PANASONIC LN1261CTR 1000PF 50V 5% C147-C148 12065A102JAT2A 1206 255.0K 1/10W R197 VISHAY CRCW06032553FK 1% 0603 80.6K 1/10W 1% R193 VISHAY CRCW060380K6FKEA 0603 22000PF 25V C131,C197 DIGI-KEY 490-3252-1-ND 10% 0402 A-10 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 87 ADSP-BF518F EZ-Board Bill Of Materials Ref. Description Reference Manufacturer Part Number Designator D7-D8 ON SEMI MBRS540T3G MBRS540T3G 20MA DIODES INC BAS70-05-7-F MA3X717E DIO005 2.5UH 30% COILCRAFT MSS1038-252NL_ IND013 33.0K 1/16W 1% R201 ROHM MCR01MZPF3302 0402 47.0K 1/16W 1% R46,R48, ROHM...
  • Page 88 SOD-123FL 22UH 20% COILCRAFT MSS4020-223MLB IND018 1UH 20% L2,L6-L7 COILCRAFT ME3220-102MLB IND019 33 1/32W 5% RN4-RN13, PANASONIC EXB-28V330JX RNS005 RN17-RN19 1.2K 1/16W 1% R4-R5,R186 VISHAY CRCW04021K20FKED 0402 4.3 1/4W 5% R185,R188 PANASONIC ERJ-8GEYJ4R3V 1206 A-12 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 89 ADSP-BF518F EZ-Board Bill Of Materials Ref. Description Reference Manufacturer Part Number Designator 2.67K 1/16W 1% R187 PANASONIC ERJ-2RKF2671X 0402 1.0M 1/16W 1% R248-R250 VISHAY CRCW04021M00FKED 0402 22UH 20% L8-L9 COILCRAFT MSD7342-223MLC IND024 330 100MHZ FER1, MURATA BLM21PG331SN1D 1.5A 0805 FER19-FER21...
  • Page 90 GSOT03-GS08 SOT23-3 D11-D12 ON SEMI ESD5Z2.5T1G ESD5Z2.5T1 SOD-523 VISHAY VESD01-02V-GS08 VESD01-02V-GS 08 SOD-523 165.0 1/10W 1% R375-R376 DIGI-KEY P165HTR-ND 0603 220.0 1/10W 1% R389 DIGI-KEY P220HTR-ND 0603 4.87K 1/10W 1% R388 DIGI-KEY 541-4.87KHCT-ND 0402 A-14 ADSP-BF518F EZ-Board Evaluation System Manual...

  • Page 91: Adsp-Bf518F Ez-Board Schematic

    ADSP-BF518F EZ-BOARD SCHEMATIC ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title TITLE Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 92 Boot from OTP memory Boot from SDRAM 32.768KHZ 18PF OSC008 18PF Boot from UART0 host ANALOG 20 Cotton Road 0805 0805 Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title DSP EBIU + CONTROL Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 93 BATTHOLDER 0805 0402 0402 0402 0402 VDDOTP VPPOTP "RTC BATTERY" ADSP-BF518F LQFP176_SOCKET 0.1UF 0.01UF 0603 0402 ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title DSP POWER, BYPASS CAPS Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 94 M25P16 SO8W 3.3V SHORTING JUMPER DEFAULT=NOT INSTALLED ANALOG 20 Cotton Road 0.01UF 0.01UF 0.01UF 0.01UF Nashua, NH 03063 0402 0402 0402 0402 0402 DEVICES 0.01UF PH: 1-800-ANALOGD 0402 ADSP-BF518F EZ-BOARD Title EXTERNAL MEMORY Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 95 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF 0.1UF PH: 1-800-ANALOGD 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 0402 ADSP-BF518F EZ-BOARD Title ADC INPUTS Size Board No. A0217-2008 AGND AGND Date 5-11-2009_10:44 Sheet...
  • Page 96 SWT017 AGND SW23 IN_VB6 LHPOUT IN_VB4 IN_VB2 IN_VA6 IN_VA4 IN_VA2 DIP6 SWT017 SW22 & 23 are only used for POST ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 97 0805 ANALOG 20 Cotton Road R390 R391 SW15 disconnects DSP from AUDIO CODEC 100K 0.01UF Nashua, NH 03063 0402 0402 0402 DEVICES PH: 1-800-ANALOGD 1000PF 0805 MUTE ADSP-BF518F EZ-BOARD Title AUDIO CODEC Size Board No. A0217-2008 AGND Date 5-11-2009_10:44 Sheet...
  • Page 98 GND14 ETXD2 ETXD2 TXD2 GND15 ETXD3 ETXD3 TXD3 GND16 ANALOG 20 Cotton Road GND17 Nashua, NH 03063 MIICRS/HWAIT MIICRS/HWAIT GND18 DEVICES 0805 PH: 1-800-ANALOGD VCC2 VCC4 CON036 ADSP-BF518F EZ-BOARD Title ETHERNET PHY SHGND Size Board No. A0217-2008 Date 5-13-2009_15:06 Sheet...
  • Page 99 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF 0.01UF Nashua, NH 03063 0402 0402 0402 0402 0402 0402 0402 0402 0402 DEVICES ADC_A0/LED1/MMC_D7/OTP_EN PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title ROTARY ENCODER, JTAG, RS232, EMMC, SD Size Board No. A0217-2008 Date 5-13-2009_16:18 Sheet...
  • Page 100 ADC_A0/LED1/MMC_D7/OTP_EN GND7 GND7 MIICRS/HWAIT GND7 GND17 GND17 DR1SEC GND17 RMII_PHYINT RESET GND8 GND8 GND8 DMAX_ALT DMAX_ALT DMAX_ALT ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title LOGIC ANALYZER CONN Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 101 0402 74LVC14A SOIC14 3.3V 3.3V "RESET" 74LVC14A SOIC14 ANALOG 20 Cotton Road C121 C120 0.01UF 0.01UF Nashua, NH 03063 0402 0402 74LVC14A DEVICES PH: 1-800-ANALOGD SOIC14 ADSP-BF518F EZ-BOARD Title RESET, LEDS, PUSH BUTTONS Size Board No. A0217-2008 Date 5-13-2009_16:18 Sheet...
  • Page 102 PWR_IN2 GND2 RSVD2 RSVD3 VDDIO1 GND3 RSVD4 RSVD5 VDDIO2 GND4 RSVD6 RSVD7 3.3V1 3.3V2 RSVD8 RSVD9 QMS52X2_SMT IDC25X2_SMTA ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title EXPANSION INTERFACE Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 103 0603 0603 ADP1611 R344 C197 R347 MSOP8 20.0K 22000PF 4.99K 0402 0402 0603 C198 ANALOG 20 Cotton Road 3300PF 0603 Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title OTP AND DUAL POWER Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...
  • Page 104 PGND Remove P11 when measuring VDDFLASH PGND IDC2X1 ANALOG 20 Cotton Road "VDDMEM" Nashua, NH 03063 COPPER DEVICES PH: 1-800-ANALOGD SHORTING ADSP-BF518F EZ-BOARD Title JUMPER DEFAULT=INSTALLLED POWER PGND Remove P10 when measuring VDDMEM Size Board No. A0217-2008 Date 5-13-2009_16:19 Sheet...
  • Page 105 DR1SEC_Z DR1SEC ABE1#/SDQM1_Z ABE1#/SDQM1 RNS005 RNS005 RNS005 RNS005 RNS005 RN21 D15_ZZ D14_ZZ D13_ZZ D12_ZZ RNS005 ANALOG 20 Cotton Road Nashua, NH 03063 MH10 MH11 MH12 DEVICES PH: 1-800-ANALOGD ADSP-BF518F EZ-BOARD Title SERIES TERMINATORS Size Board No. A0217-2008 Date 5-11-2009_10:44 Sheet...

  • Page 106: Index

    2-24 P4 (expansion interface II), 1-25, 2-24 P5-7 (DMAX land grid array), 1-26, battery 2-25 holder connector (J12), 2-22 ZP1 (debug agent), 2-25 supply, 1-24 contents, of this EZ-Board package, bill of materials, core voltage, ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 107 JP18 Ethernet isolate mode, 1-20, 2-16 external memory, 1-13, 1-14 JP3 (flash WP), 2-15 JP6 (mic select), 1-22 P10 (VDDMEM power), 1-27, 2-17 P11 (VDDFLASH power), 1-27, 2-17 P8 (VDDINT power), 1-27, 2-16 P9 (VDDEXT power), 1-27, 2-17 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 108 1-27 PPI interface connections, 1-19 notation conventions, expansion interface II connector (P3), 1-19, 2-24 product overview, xiii oscilloscope, 1-27 programmable flag inputs PH0 -1, 1-25 OTP_EN signal, 1-25 OTP flag enable jumper (JP14), 2-15 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 109 1-9, 1-12, expansion interface II connectors (P4), 1-15, 1-25 1-23, 2-24 startup, of this EZ-Board UART1_RX signal, 2-11, 2-16 CCES, UART1_TX signal, 2-11, 2-16 SW10 (UART0 setup) switch, 2-11 U-Boot, universal boot loader, 1-18 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 110 1-27 VDDINT power jumper (P8), 2-16 voltage domain, 1-27 VDDMEM power jumper (P10), 2-17 voltage domain, 1-27 VisualDSP++ environment, 1-10 voltage planes, 1-27, 2-16, 2-17 wall adaptor connector (J3), 1-9, 1-25 watchdog timer, 1-24 ADSP-BF518F EZ-Board Evaluation System Manual...
  • Page 111 Authorized Distribution Brand： Website： Welcome to visit www.ameya360.com Contact Us： Address： 401 Building No.5, JiuGe Business Center, Lane 2301, Yishan Rd Minhang District, Shanghai , China Sales： Direct +86 (21) 6401-6692 Email amall@ameya360.com 800077892 Skype ameyasales1 ameyasales2 Customer Service： Email service@ameya360.com Partnership：...

Table of Contents