Page 1 No part of this handbook may be reproduced, transcribed, translated into any language or transmitted in any form whatsoever without the prior written consent of Codan Pty Ltd. © Copyright 1994 Codan Pty Ltd. Codan Part No. 15-04034 Issue 3, September 1995...
Page 3: Table Of Contents
Contents 1. About this handbook............1-1 Who should use this handbook ..........1-1 Icons and standards..............1-1 Glossary................. 1-2 2. Overview ................. 2-1 The Radiophone front panel ..........2-4 The transceiver and control head rear panels......2-8 3. Installation ..............3-1 Mounting the transceiver ............
Page 4 Contents Selecting channels ..............4-9 Using the Channel buttons ......... 4-9 Using the Select Channel button ........4-10 Adjusting the volume............4-11 Using the clarifier ..............4-12 Using the mute controls ............4-13 Voice mute ..............4-13 Selective call mute ............4-13 Tuning the antenna ..............
Page 5 Contents Returning a received call–general........5-20 Reviewing the list of received calls in memory ....5-21 Reviewing calls held in memory ........5-22 Recalling calls held in memory ........5-24 Using the beacon feature............5-25 Selective beacon mode........... 5-27 (99) beacon mode............5-29 Using the external alarm feature ..........
Page 6 Contents 8. Using tone call ..............8-1 Setting up tone call ..............8-3 Enabling a channel for tone calling........8-6 Transmitting a tone call ............8-9 9. Making a telephone interconnect call......9-1 Enabling the telephone mode..........9-2 Making a telephone call............9-3 Sending a disconnect message ..........
Page 7 Contents 11. Changing the set-up options........11-1 Set-up option links............... 11-1 The control head link ............. 11-2 Changing the position of the control head link....11-3 The microprocessor PCB link ........11-4 Inserting the microprocessor PCB link ......11-5 Reviewing set-up options............. 11-6 PTT timer ................
Page 8 Contents List of drawings Figure Title Page The control head front panel .............2-7 The transceiver rear panel............2-9 The control head rear panel............2-9 Typical vehicle installation ............3-1 Telephone interconnect block diagram ........9-1 The control head link ..............11-2 11.1 The microprocessor link ............11-4 11.2 Outback HF Radiophone...
Page 9: About This Handbook
1. About this handbook Who should use this handbook This handbook is written for the person who installs and operates the Codan Outback HF Radiophone. Icons and standards The following icons and standards have been used throughout this handbook. This icon…...
Page 10: Glossary
About this handbook Glossary Antenna Driver Forward Error Correction Liquid Crystal Display Lower Side Band The corporate name for a Maritime Radphone service (superseded by Telstra) Personal Identification Number Miscellaneous facilities Press To Talk Remote RFDS Royal Flying Doctor Service Receive Selective call Decode Telstra...
Page 11: Overview
2. Overview Your Outback HF Radiophone employs the latest concepts in design and reliability for long range communications. It has been designed for 12V DC operation in mobile installations. The Outback HF Radiophone consists of a transceiver and a separate control head, automatic tuning whip antenna, vehicle mounting cradle, extension loudspeaker and all interface control and coaxial cables (6 metres).
Page 12 0.25 MHz to 30 MHz. A maximum of 501 transmit and receive channels can be pre-programmed in the factory, or by an authorised Codan dealer. You, as a user, can program the remaining 99 receive only channels from the control panel as P-channels.
Page 13 Overview Your transceiver can be used as a free-tuning receiver Free-tuning receiver covering the world broadcast bands over the frequency range of 250 kHz to 30 MHz. Tone calling This facility allows you to send a tone call (two tones transmitted simultaneously) to call the RFDS or OTC (Telstra).
Page 14: The Radiophone Front Panel
Overview The Radiophone front panel The front panel of the Radiophone control head (figure 2.1 on page 2-7) has the following designations: Item No. Item Function Switches the transceiver on or off. On/Off The indicator is lit when the transceiver is transmitting.
Page 15 Overview Item No. Item Function Selects either channel or band scan. The indicator Scan is lit when the scan mode is ’on’. Liquid Crystal Display (LCD) shows the channel number and frequency. It also shows messages regarding the operation of the transceiver. Mutes all audio until a selective call is received.
Page 16 Overview Item No. Item Function Transmits a tone call to a selected OTC station. Tone Call Transmits a tone alarm call on selected RFDS Emgcy frequencies operating within the Royal Flying Doctor Service of Australia. Reduces the programmed frequency in steps of Fast 1 kHz.
Page 17: The Control Head Front Panel
Overview Item No. Item Function Selects the next lower channel. It also keys in number 9. Selects the next higher channel. It also keys in number 4. Decreases the audio volume. It also keys in the number 0 and the letter P. Increases the audio volume.
Page 18: The Transceiver And Control Head Rear Panels
Overview The transceiver and control head rear panels The transceiver and control head rear panels (figures 2.2 and 2.3 on page 2-9) show the following items: Item No. Item Function Antenna socket. Earth (ground) screw. Automatic antenna control socket. 12V DC power lead. External 8 ohm loudspeaker socket.
Page 19: The Transceiver Rear Panel
Overview Figure 2.2: The transceiver rear panel Mounting cradle Figure 2.3: The control head rear panel Outback HF Radiophone...
Page 20 Overview 2-10 Outback HF Radiophone...
Page 21: Installation
3. Installation On receipt of your Outback HF Radiophone package, check the contents against the packing list. Ensure all items are available before commencing installation. The following notes provide guidance to your vehicle installation but are not intended to be comprehensive procedures.
Page 22: Mounting The Transceiver
Installation Mounting the transceiver The transceiver must be mounted in a position that will not cause injury to occupants in the event of a motor vehicle accident. Mount the transceiver and control head in a position that allows: • easy access to the control panel •...
Page 23: Mounting The Control Head
Installation Insert the transceiver side rails into the T-section slides and push the transceiver fully into the cradle. Apply gentle pressure to the front panel of the transceiver and lock into the cradle by turning the cam catches one quarter of a turn in either direction with a suitable tool or small coin.
Page 24 Installation Remove the two cradle screws and washers securing the mounting cradle to the control head. Secure the mounting cradle into position. Ensure there is sufficient space at the rear of the cradle for the control cable. Secure the control head to the mounting cradle with the two screws and washers.
Page 25: Mounting The Antenna
Installation Mounting the antenna The antenna is a critical element in any communication system. It cannot be overstressed that correct installation of the antenna is of prime importance to the operation of your Radiophone. To obtain the best performance from your Radiophone, it is important to consider the following points when installing your antenna: •...
Page 26: Power Supply
Installation Power supply Ensure that the power supply to operate your Radiophone is 12V DC—usually vehicle batteries. All installations should be checked by a qualified technician before power is applied to the Radiophone. The heavy duty six metre length of power cable has been selected to minimise the voltage drop between the battery and transceiver when in transmit mode.
Page 27: Grounding
Installation Grounding An adequate ground, or earth, is essential for satisfactory operation of the Radiophone. A chassis ground or earth screw is provided on the rear panel of the transceiver. Install an earth cable between this screw and an earth point. Use copper braid or heavy duty cable. The control head should also be earthed.
Page 28 Installation Outback HF Radiophone...
Page 29: Using The Radiophone
4. Using the Radiophone This section covers the basic steps necessary to operate your Radiophone. It outlines how you use the control buttons to make various adjustments and settings, and includes transmitting and receiving calls. Throughout this section all displays show examples of channel and frequency numbers.
Page 30: Switching The Radiophone On Or Off
Using the Radiophone Switching the Radiophone on or off When you switch the Radiophone on, the display usually shows the last settings before the Radiophone was switched off. If your Radiophone has a personal identification number (PIN) allocated, then the display will request you to enter your PIN.
Page 31: Switching On Or Off With A Pin
Switching on or off with a PIN It is most important not to forget your PIN, otherwise you will never be able to switch on your Radiophone. If this happens, you will have to return the transceiver to Codan for them to delete the allocated number.
Page 32: The Radiophone Display
Using the Radiophone The Radiophone display The display provides you with visual indication of the selected channel numbers, and the transmit and receive frequencies. In addition, it shows you messages that will assist you when operating your Radiophone. A detailed description of all the messages can be found in section 12, Display messages.
Page 33 Using the Radiophone Displaying the channel options There are several options that you can select your Radiophone to use. The display button gives you the freedom to check the options that have been selected (enabled) at the time of purchase by viewing the option bar in the display. Step Action…...
Page 34 Using the Radiophone Dimming the display and indicators The backlit display and indicators are at maximum brightness when you switch the Radiophone on. This procedure explains how to reduce the brightness of the display and indicators. Step Action… Display shows… Remarks…...
Page 35: Reviewing The Eprom Version And Options
Using the Radiophone Review the EPROM version and options This facility allows you to review the EPROM version and some of the options fitted to your Radiophone. This procedure is repeated in section 12, Reviewing the EPROM program content. Step Action…...
Page 36 Using the Radiophone Step Action… Display shows… Remarks… The top line shows the cont. number of channels programmed by the factory or agent, this can be up to 501. The second line shows the number of channels programmed by the user, this can be up to 99 or 89 with the telephone mode enabled.
Page 37: Selecting Channels
Using the Radiophone Selecting channels There are two methods of selecting channels: • Using the Channel Up or Down buttons—this method is preferable when you are changing to an adjacent channel • Using the Select Channel button—since there may be up to 600 channels available, this method is preferable when you are changing channels over a large range.
Page 38: Using The Select Channel Button
Using the Radiophone Using the select channel button Step Action… Display shows… Remarks… Press Select Channel If the channel was This is an example of installed by the how to recall channel 2. factory, press Slow For details on F and P channels, refer to If the channel was sections 6 &...
Page 39: Adjusting The Volume
Using the Radiophone Adjusting the volume This procedure tells you how to adjust the volume. When the mute is on, pressing any of the volume control buttons opens the mute for approximately one second. This allows you to hear the background noise, thus assisting you to select the correct level. When you switch your Radiophone on, the volume level is at the last used setting.
Page 40: Using The Clarifier
Using the Radiophone Using the clarifier The clarifier buttons raise or lower the frequency in steps of 10 Hz. This allows you to fine tune the Radiophone to obtain the best clarity for received voice calls. Step Action… Display shows… Remarks…...
Page 41: Using The Mute Controls
Using the Radiophone Using the mute controls There are two mute controls that inhibit background noise until a signal is received: • Voice Mute—this function inhibits background noise until a voice signal appears. • S'Call Mute—this function inhibits background noise until your transceiver has been selectively called.
Page 42: Tuning The Antenna
Using the Radiophone Tuning the antenna Before using the selected channel, the antenna must be tuned to the transmission frequency. Step Action… Display shows… Remarks… Select the Refer to page 4-9, required channel. Selecting channels. Press If tuning was successful The Tx indicator will be lit during this procedure.
Page 43: Receiver Tuning Mode
Using the Radiophone Receiver tuning mode Your Radiophone can be tuned to receive frequencies in the range 0.25 MHz to 30 MHz. Note: Due to internally generated signals, it will be difficult to receive on and near frequencies 6599, 9998, 13199, 19799, 19995 and 26399 kHz. While you are in receiver tuning mode you cannot receive selective calls or tone calls.
Page 44: Using The Receiver Tuning Or Buttons
Using the Radiophone Using the Receiver Tuning buttons Step Action… Display shows… Remarks… Press and hold The display scrolls Use the Fast buttons for any Receiver through the numbers coarse tuning (1 kHz Tuning button. until you release the steps) and the Slow button.
Page 45: Selecting The Desired Frequency
Using the Radiophone Selecting the desired frequency This procedure allows you to select the frequency you desire, and therefore save time. Once you have selected a frequency you have the option to store the frequency as a P- channel or exit this facility. Step Action…...
Page 46 Using the Radiophone Step Action… Display shows… Remarks… If you wish to store this selection as a P-channel, refer to the procedure Storing a tuned receive only frequency on page 4-19. There are three ways to exit this mode, either press the Channel buttons, Select...
Page 47: Storing A Tuned Receive Only Frequency
Using the Radiophone Storing a tuned receive only frequency You can store a tuned receive only frequency as a personal channel number in the range P1 to P99. This frequency can then be selected as outlined on page 4-9, Selecting channels. This procedure can only take place if your Radiophone is in the tune receive only mode, as outlined on page 4-17 Selecting the desired frequency Step...
Page 48: Changing The Operating Mode (Usb - Lsb)
Using the Radiophone Changing the operating mode (USB - LSB) Your Radiophone has the facility to operate in either Upper Side Band (USB) or Lower Side Band (LSB) mode. When receiving broadcast stations such as the BBC or Radio Australia, changing between USB and LSB may reduce interference. Unless otherwise advised, your Radiophone is normally programmed to operate in the USB mode.
Page 49: Transmitting
Using the Radiophone Transmitting It is important when transmitting to use the microphone to its best advantage. By following the notes under Using the microphone you will obtain the best transmitting results. This section covers two topics: • using the microphone •...
Page 50: Transmitting A Message
Using the Radiophone Transmitting a message Step Action… Display shows… Remarks… Select a channel The display shows the Refer to page 4-9, for transmission. channel number and the Selecting channels. transmit (Tx), and receive (Rx) frequencies. Check the display If the channel has been to see if the enabled, continue with channel transmit...
Page 51 Using the Radiophone Step Action… Display shows… Remarks… Press the PTT The Tx indicator flashes button on the during transmission. microphone and commence talking. Transmit your message following the notes outlined in Using the microphone on page 4-21. Outback HF Radiophone 4-23...
Page 52 Using the Radiophone 4-24 Outback HF Radiophone...
Page 53: Using Selective Call
5. Using selective call Selective call allows you to call Radiophones or equivalent transceivers. This can be best likened to a normal telephone system where the called station has a unique calling address or number. However, the operator can also call a group of stations if desired.
Page 54: Selective Call Terms
Using selective call Selective call terms The following terms are used in this section. This term… Means… Called address The four digit identification number of the Radiophone being called. Beacon call A call used to check signal conditions. Decoding Receiving and translating the encoded message. Encode The translation of the identification number and instructions into a coded message for transmission.
Page 55 Using selective call This term… Means… Revertive Signal A signal automatically transmitted back from the receiving Radiophone to indicate message received and decoded satisfactorily. This signal does not apply to group calls. Selective beacon A call used to check signal conditions to a selected station. call Self-identification The four digit identification number of the calling...
Page 56: Setting Up Selective Call
Using selective call Setting up selective call There are several features that need to be set up before selective call is used: • the preamble time period • the called address • the self-identification address • the beacon on or off. You may cancel the procedure at any time by turning the Radiophone off (press the On/Off button).
Page 57: Setting The Pre-Amble Time Period
Using selective call Setting the pre-amble time period Ensure your Radiophone is switched off. Hold down Hold the Selective Call button down for Selective Call approximately three seconds. and press On/Off This turns the Radiophone on and into the preamble set-up mode.
Page 58: Setting The Fixed Called Address
Using selective call Setting the fixed called address There are two ways of entering the called address: as below, which is fixed and cannot be changed easily by the method used on page 5.14, Transmitting a selective call (Open access selective call) which allows the address to be entered from the front panel of the control head and is easy to change to call another Radiophone or transceiver.
Page 59: Enabling The Beacon Mode
Using selective call Use the numeric You can override an buttons to enter existing address by the self- entering a new number. identification address number. To delete an address, enter four zeros. Press Once Enter has been pressed, the self Enter identification address has been set and can only be...
Page 60: Setting Tone Calls
Using selective call Press This sets the new beacon setting and moves to the Enter next feature (tone calling). For more information on tone calling, refer to section 8, Using tone call. Setting tone calls This procedure is This procedure is not required at covered in detail in this time.
Page 61: Checking If A Channel Is Enabled For Selective Call
Using selective call Checking if a channel is enabled for selective call A channel must be enabled for the selective call facility to operate. If the channel you wish to use has not been enabled, refer to the procedure Enabling a channel for selective call on page 5-12.
Page 62: Selective Call Mute Enable Or Inhibit
Using selective call Selective call mute enable or inhibit This facility enables or inhibits the operation of the S’Call Mute button. When S’Call Mute is inhibited you cannot operate selective call mute. Step Action… Display shows… Remarks… Turn the No display. Before moving the link, Radiophone off note its original position.
Page 63 Using selective call Return the control Refer to section 11, head link to its Changing the position of original position the control head link. (E). Replace the cover before switching on your Radiophone. Outback HF Radiophone 5-11...
Page 64: Enabling A Channel For Selective Call
Using selective call Enabling a channel for selective call This procedure explains how to enable an existing programmed channel for selective calling. To achieve this you are required to copy the existing programmed channel into the P-channel program, as outlined below. This procedure is similar to Enabling a channel for tone call in section 8.
Page 65 Using selective call Step Action… Display shows… Remarks… Press You will hear a ’pip’. Selective Call Repeat this action until an S appears in the left hand position of the options bar. Press You will hear a ’pip’. Enter Use the numeric You will notice that the buttons to enter display automatically...
Page 66: Transmitting A Selective Call
Using selective call Transmitting a selective call For selective call to operate you must have your self-identification number programmed, refer to Setting the self-identification address on page 5-7. Step Action… Display shows… Remarks… Select the Ensure the channel is required channel. enabled for selective call.
Page 67 Using selective call Step Action… Display shows… Remarks… If your The Tx indicator will be Radiophone has lit and you will hear a the fixed called ’warbling’ sound for address, press approximately 10 This is an example of the twice in seconds.
Page 68 Using selective call Step Action… Display shows… Remarks… Press You will hear a ’warbling’ sound for approximately Selective Call 10 seconds. If the call was You will hear no sound if successfully it was a group call. received and Normal transmission can decoded, within now commence.
Page 69: Receiving A Selective Call
Using selective call Receiving a selective call Your Radiophone automatically completes the following event when receiving a selective call. Step Action… Display shows… Remarks… No action, the When you receive a call, Radiophone tones will be heard on the automatically loudspeaker.
Page 70 Using selective call Notes If the microphone PTT button is not pressed before the end of the tones: cont. • the called display will remain on to indicate that a call was received • a ’pip’ will be heard every four seconds •...
Page 71: Answering A Received Call
Using selective call Answering a received call This procedure is used when you want to begin talking on a call that has just been received on your Radiophone which is still producing the ringing tone. Step Action… Display shows… Remarks… The display shows the channel number and the...
Page 72: Returning A Received Call-General
Using selective call Returning a received call—general This procedure is used when you want to return a call that has been stored in the memory stack. Step Action… Display shows… Remarks… Select the call you Refer to Reviewing the wish to return. list of received calls in memory on page 5-21.
Page 73: Reviewing The List Of Received Calls In Memory
Using selective call Reviewing the list of received calls in memory Your Radiophone is able to record up to 10 calls in memory from various stations. These may be on different channels if your Radiophone is on scan mode. These calls are recorded in a memory stack awaiting your review.
Page 74: Reviewing Calls Held In Memory
Using selective call Reviewing calls held in memory This procedure allows you to review all calls held in the memory in the order received. Ensure the Radiophone is not in scan mode when reviewing the list of selective calls received. If no calls have been made to your Radiophone, the display will continue to show both the channel and frequency numbers.
Page 75 Using selective call Step Action… Display shows… Remarks… Press either Pressing will change the display to show the next call, and will reverse the order viewed. The identification address and corresponding channel number will change for each caller. If you wish to return a call, refer to Returning a received call–...
Page 76: Recalling Calls Held In Memory
Using selective call Recalling calls held in memory Ensure the Radiophone is not in scan mode when recalling a selective call held in memory. Step Action… Display shows… Remarks… No action. Press Select Channel and then Selective Call Check that the The display shows the The Radiophone sends channel is free...
Page 77: Using The Beacon Feature
Using selective call Using the beacon feature The beacon facility is used to check signal conditions between two Radiophones fitted with selective call. The beacon facility has two modes of operation: • selective beacon mode • base station (99) beacon mode. Selective beacon mode With the beacon facility enabled on a Radiophone, it will transmit a beacon signal on receipt of a selective beacon call...
Page 78 Using selective call General information for both modes of operation The beacon signal consists of four long tones. Self-identification addresses ending in 99 should be avoided as these will cause confusion. No alarm or call is recorded at the receiving Radiophone, only the Tx indicator flashes.
Page 79: Selective Beacon Mode
Using selective call Selective beacon mode Step Action… Display shows… Remarks… Ensure your The last channel selected. Radiophone is switched on. Select the Refer to section 4, required test Selecting channels. channel and tune the antenna. Press When this button is pressed, the S’Call Mute Selective Call...
Page 80 Using selective call Step Action… Display shows… Remarks… Check that the The transmit indicator channel is free will be lit and you will from traffic, then hear a warbling sound for press approximately 10 seconds. If the call is Tune Immediately the call is successfully decoded you received, the display...
Page 81: Beacon Mode
Using selective call (99) beacon mode Step Action… Display shows… Remarks… Ensure your The last channel selected. Radiophone is switched on. Select the Refer to section 4, required test Selecting channels. channel and tune the antenna. Press When this button is pressed, the S’Call Mute Selective Call...
Page 82 Using selective call Step Action… Display shows… Remarks… Check that the The transmit indicator channel is free will be lit and you will from traffic, then hear a warbling sound for press approximately 10 seconds. If the call is Selective Immediately the call is Call successfully decoded you...
Page 83: Using The External Alarm Feature
Using selective call Using the external alarm feature An external alarm facility is made available through the external alarm socket on the rear panel (refer to figure 2.2). A pair of relay contacts are wired to the socket, which close for two minutes when your Radiophone receives a selective call.
Page 84: Testing The Selective Call Functions
Using selective call Testing the selective call functions This is a special test mode which will not be required for normal operations. In this mode, the Radiophone decodes all selective call signals, and displays the address to which it was sent and the self identification of the calling station. No called alarms or revertives are generated.
Page 85 Using selective call Step Action… Display shows… Remarks… No action. When a selective call is received, the display shows the called station identification address and the self identification address. To exit this mode, You must switch your press Radiophone off and on again to clear this mode.
Page 86 Using selective call 5-34 Outback HF Radiophone...
Page 87: Using The Receiver In Scan Mode
6. Using the receiver in scan mode In the receiver scan mode your Radiophone is able to listen into selected channels for transmitted signals. Once a signal has been detected, the Radiophone holds that channel for a pre-selected time before continuing with the scan. This is determined at set-up.
Page 88: Scan Mode Terms
Using the receiver in scan mode Scan mode terms The following abbreviations are shown in the display. Frequency Lower side band Lower and upper side band Upper side band Outback HF Radiophone...
Page 89: Setting Up The Scan Mode
Using the receiver in scan mode Setting up the scan mode The scan program allows your Radiophone to scan a selected number of frequencies. Your Radiophone also has the option to run in normal or Auto-scan mode. The Auto- scan mode automatically puts the Radiophone back into scan after five minutes of inactivity (such as no channel change, PTT, tune etc.).
Page 90 Using the receiver in scan mode Step Action… Display shows… Remarks… Press Switches to Auto option. Scan If this is the option you want, go to step 7. Press Switches from inhib to ENAbLE. Scan Pressing the Scan button again returns you to the display in step 2.
Page 91: Programming The Channels To Be Scanned
Using the receiver in scan mode Programming the channels to be scanned In normal operating conditions, a maximum of 15 channels can be programmed to be scanned in sequence for audio (voice) signals. Channels required to operate on a selective call must be programmed within the first eight entries. Ensure your Radiophone is switched on and scan program has been enabled.
Page 92 Using the receiver in scan mode Step Action… Display shows… Remarks… Press The channel is programmed for Scan scanning. Repeat this procedure until all channels you want to scan have been programmed. Press The channels you have programmed are now Enter registered within the transceiver.
Page 93: Receiving In Scan Mode
Using the receiver in scan mode Receiving in scan mode This procedure covers three topics when receiving in scan mode. Ensure your Radiophone is switched on before proceeding with any of the following: • start scanning • stop scanning • changing the scan mode.
Page 94: Changing The Scan Mode
Using the receiver in scan mode Changing the scan mode There are three scan mode options available to you which can be selected by repeatedly pressing the Voice Mute button. Your Radiophone must be in the scan mode to complete this operation (refer to Receiving in scan mode on page 6-7). •...
Page 95 Using the receiver in scan mode Step Action… Display shows… Remarks… Hold scanning You will hear two ’pips’ and the Voice Mute Press again indicator will be lit. Voice Mute If you want Continuous scanning, go to step 4. To exit this mode go to step 5.
Page 96: Using Selective Call In Scan Mode
Using the receiver in scan mode Using selective call in scan mode Selective call scanning ensures that you are only alerted when the incoming calls are specifically addressed to you. This facility also allows the Radiophone to store in memory the addresses of up to ten stations that may have tried to contact the Radiophone whilst unattended.
Page 97 Using the receiver in scan mode Step Action… Display shows… Remarks… If the call is If the call is not answered addressed to the immediately, the Radiophone the scanning stops for 2½ display changes. minutes and you will hear 'pips' every 4 Every time an seconds.
Page 98: Programming Frequency Band Scan
Using the receiver in scan mode Programming frequency band scan The band scanning facility enables the Radiophone to scan between two programmed frequencies. You can program the frequency bands to suit your needs. Up to 30 bands can be programmed into the Radiophone, and stored between channels P70 and P99.
Page 99 Using the receiver in scan mode Step Action… Display shows… Remarks… Using the numeric This is an example of buttons, enter the selecting a band scan to start frequency to start at 4000 kHz. the nearest 100 Press The decimal points are automatically entered by Enter the Radiophone.
Page 100 Using the receiver in scan mode Step Action… Display shows… Remarks… If a mode change Each press selects the is required, press next option; upper side band (U), lower side band (L), both side bands (LU) and back to (U). Press Enter Enter the channel...
Page 101 Using the receiver in scan mode Notes: If the display shows ’prog USEd’, either enter another channel number or press the Enter button to overwrite the existing information. If the display shows ’prog inhib’, the scan facility is inhibited. Refer to section 11, Changing the set up options.
Page 102: Scanning Frequency Bands
Using the receiver in scan mode Scanning frequency bands The band scanning facility enables the Radiophone to scan between two programmed frequencies, refer to Programming frequency band scan on page 6-12. There are two rates of scan available, fast and slow: •...
Page 103 Using the receiver in scan mode Step Action… Display shows… Remarks… To pause the scan, The display shows the You may move between press any of the channel number and the the frequencies by using fast or slow Tune current frequency. any of the Tune Rx Rx Frequency Frequency buttons.
Page 104: Deleting Unwanted Scan Channels
Using the receiver in scan mode Deleting unwanted scan channels Step Action… Display shows… Remarks… Ensure your Radiophone is switched on. Select the channel Refer to section 4, you wish to Selecting channels. delete. An example for channel Press Enter Press this button Two ’0’s entered as a twice...
Page 105: Programming Channels
Your Radiophone can store up to 600 channels. A maximum of 501 transmit and receive channels can be pre-programmed by the factory or a Codan agent. The remaining 99 programmable channels (P-channels) can be set by you from the front panel, either by copying from an existing programmed transmit/receive channel or adding a receive only frequency channel.
Page 106: Using Tone Call
8. Using tone call The tone call facility allows stations within a network to call (tone encode–TE) other stations using the transmission of tones. The following only applies where your Radiophone is required to operate into a private network using the transmission of tones for calling.
Page 107 Using tone call Tones t1 and t2 are given values in the factory. You can override these settings by using the following set-up procedure. To reinstate the original values, either enter ’0’ frequency or delete the latest channel information. All displays in this section show examples of channel and frequency numbers.
Page 108: Setting Up Tone Call
Using tone call Setting up tone call This procedure is similar to setting up selective call. Once in the set-up mode, you can skip through the non-important steps by pressing the Enter button. Step Action… Display shows… Remarks… To start the set-up Hold the Call button mode, hold down down for approximately...
Page 109 Using tone call Step Action… Display shows… Remarks… Use the numeric There are four pairs of buttons to enter tone frequencies that you the t1 Hi tone can set, t1, t2, t3 and t4. frequency. If you enter an incorrect The t1 &...
Page 110 Using tone call Step Action… Display shows… Remarks… Steps 6 to 9 are The display shows the repeated by the same as in steps 6 to 9, Radiophone for except for the tone and t2, t3 and t4. frequency numbers. When all four tone pairs are recorded, the display returns to the first set-up...
Page 111: Enabling A Channel For Tone Calling
Using tone call Enabling a channel for tone calling This procedure explains how to enable a channel for tone calling. Initially, you need to select a channel frequency you want to enable, and then choose a tone call pair for that frequency.
Page 112 Using tone call Step Action… Display shows… Remarks… Press You will hear a ’pip’. Selective Call An example for tone pair Repeat this action until a ’t’ and the required tone pair appear in the left hand two spaces of the options bar. Press You will hear a ’pip’.
Page 113 Using tone call Step Action… Display shows… Remarks… If the channel is The display reverts back The information will already used, you to normal. either be stored under an can either enter existing channel number, another number or or you will have created press Enter again a new one.
Page 114: Transmitting A Tone Call
Using tone call Transmitting a tone call Before commencing this procedure, ensure the Voice Mute button is in the off position (indicator off) and the antenna is tuned to the selected frequency. Step Action… Display shows… Remarks… Use the Channel Ensure the channel you buttons or Select select is enabled for tone...
Page 115 Using tone call 8-10 Outback HF Radiophone...
Page 116: Making A Telephone Interconnect Call
9. Making a telephone interconnect call If a base station transceiver is linked to an IPC-500 telephone interconnect unit (figure 9.1), it can make and receive telephone calls through the public switched telephone network (PSTN). Using the selective call facility on your outstation Radiophone to signal the base station telephone interconnect, you can dial any telephone number of up to 16 digits.
Page 117: Enabling The Telephone Mode
Making a telephone interconnect call Enabling the telephone mode You can only make telephone calls from your outstation Radiophone if the telephone mode is enabled. You can still use all the Radiophone’s other functions while this mode is enabled. Step Action…...
Page 118: Making A Telephone Call
Making a telephone interconnect call Making a telephone call This procedure explains how to make a telephone call from your outstation Radiophone to the base station transceiver IPC-500 system. Ensure your Radiophone is switched on before commencing this operation and the antenna is tuned on the selected channel, refer to Tuning the antenna in section 4.
Page 119 Making a telephone interconnect call Step Action… Display shows… Remarks… Press Enter Use the numeric This example number is buttons to enter 08 336 0311. (Numbers the telephone wrap around in the number you wish display from the bottom to call. to the top row, including the CALL area—16 digits.)
Page 120 Making a telephone interconnect call Step Action… Display shows… Remarks… When the The indicator light telephone flickers whilst talking. subscriber On completing the call, answers, they will you must send a hear a short pre- disconnect message recorded message (refer to Sending a informing them disconnect message on that this is a radio...
Page 121: Sending A Disconnect Message
Making a telephone interconnect call Sending a disconnect message When a telephone call is made, a circuit is automatically established between your outstation Radiophone and the telephone party that the base IPC-500 has dialled. When you finish a call, this call line must be disconnected. This is achieved by sending a disconnect message from your Radiophone to the IPC-500.
Page 122 Making a telephone interconnect call Step Action… Display shows… Remarks… Press The display does not The Tx indicator lights change. and you will hear a Selective Call warbling sound for approximately 10 seconds as the Radiophone sends your call. When you hear five long beeps you know that the circuit has been disconnected.
Page 123: Storing A Telephone Number
Making a telephone interconnect call Storing a telephone number This facility allows you to store up to 10 telephone numbers into your Radiophone, which can be re-called by entering a single code number (0 to 9) rather than a complete telephone number. Ensure your Radiophone is switched on and a selective call enabled channel has been selected before commencing this procedure.
Page 124 Making a telephone interconnect call Step Action… Display shows… Remarks… Press You can store this telephone number as a Enter single code number, t0 to Use the numeric Your selection has now buttons to enter been made. the code number you want, 0 to 9.
Page 125: Reviewing The Stored Telephone Numbers
Making a telephone interconnect call Reviewing the stored telephone numbers This facility allows you to review all the numbers you have stored. Ensure your Radiophone is switched on and a selective call enabled channel has been selected before commencing this operation. Step Action…...
Page 126 Making a telephone interconnect call Step Action… Display shows… Remarks… Keep pressing the This example is for number 02 971 2233. Select Channel button to scroll If you don’t press Select through all the Channel again, after one stored numbers. second the display changes to give you the option to call this...
Page 127: Calling A Stored Telephone Number
Making a telephone interconnect call Calling a stored telephone number This procedure explains how to make a telephone call to a number you have previously stored. Ensure your outstation Radiophone is switched on and a selective call enabled channel has been selected before commencing this operation. Ensure the antenna is tuned on the selected channel, refer to Tuning the antenna in section 4.
Page 128 Making a telephone interconnect call Step Action… Display shows… Remarks… Use the numeric This example shows the buttons to enter recall number t1, and the the number you telephone number to call require between 0 as 08 336 0311. After one second the and 9.
Page 129 Making a telephone interconnect call Step Action… Display shows… Remarks… When the The indicator light telephone flickers whilst talking. subscriber On completing the call, answers, they will you must send a hear a short pre- disconnect message recorded message (refer to Sending a informing them disconnect message on that this is a radio...
Page 130: Deleting A Stored Telephone Number
Making a telephone interconnect call Deleting a stored telephone number This facility allows you to delete a stored telephone number. Ensure your Radiophone is switched on and a selective call enabled channel has been selected before commencing this operation. As soon as you enter the number to be deleted, it is deleted immediately from memory without any warning.
Page 131 Making a telephone interconnect call Step Action… Display shows… Remarks… Press Enter See page 9-15. Use the numeric buttons to enter the stored number you want to delete, 0 to 9. Continually press Your Radiophone is ready for normal Voice Mute operation.
Page 132: Received Call Messages
Making a telephone interconnect call Received call messages When a call has been received and decoded, the display provides you with different messages to indicate the type of call received. The following examples show you the type of messages that will appear on the display. This display…...
Page 133: Reviewing The List Of Received Calls In Memory
Making a telephone interconnect call Reviewing the list of received calls in memory Your Radiophone is able to record up to 10 calls in memory from various stations. These may be on different channels if your Radiophone is in scan mode. These calls are recorded in a memory stack awaiting your review.
Page 134 Making a telephone interconnect call Step Action… Display shows… Remarks… Press and hold The options for the channel are displayed. Select Channel Release If any calls have been The first call recorded recorded, the display will be displayed first. In Select Channel shows...
Page 135: Returning A Call
Making a telephone interconnect call Returning a call This procedure explains how to return a telephone call to one of the numbers recorded in the memory stack. Ensure your Radiophone is switched on before commencing this operation. Ensure the antenna is tuned on the selected channel, refer to Tuning the antenna in section 4.
Page 136 Making a telephone interconnect call Step Action… Display shows… Remarks… Press The transceiver automatically selects the Selective Call correct channel, and displays the self identification address (1234) of the caller. Press Enter Check that the The display does not The Tx indicator lights channel is free change.
Page 137 Making a telephone interconnect call Step Action… Display shows… Remarks… When the The display shows The indicator light telephone flickers whilst talking. subscriber The viewed call is answers, they will deleted from the memory for any call that has not hear a short pre- stack when you press the been returned.
Page 138: Rfds And Telstra Services
10. RFDS and Telstra services The Radiophone has been customised for simple operation into the following remote area safety services: • the Royal Flying Doctor Service (RFDS) • Telstra (formerly OTC). Channel frequencies for both services have been programmed into the Radiophone and some front panel controls have been dedicated to operate into those facilities provided.
Page 139: Royal Flying Doctor Service
RFDS and Telstra services Royal Flying Doctor Service The Royal Flying Doctor Service (RFDS) is a vital communications link in the Australian outback. Apart from maintaining contact and a listening watch for medical services, the organisation also provides general communication facilities which includes radiotelephone and lettergram services.
Page 140 RFDS and Telstra services On receipt of this call, the RFDS base station will deal only with the outstation seeking medical advice. Should the frequency in question be heavily congested with traffic and ’quiet’ periods are not forthcoming, the above medical call should be proceeded by a 20 second RFDS emergency alarm call.
Page 141: Making An Rfds Emergency Call
RFDS and Telstra services Making an RFDS emergency call The RFDS Emgcy button is used to call the Royal Flying Doctor Service. This button will only function if the selected channel is enabled for emergency calls. Step Action… Display shows… Remarks…...
Page 142 RFDS and Telstra services Step Action… Display shows… Remarks… Wait for a reply The display does not If the call was received before change. by an attended RFDS transmitting your base, they will reply message. immediately. If the call was received by an unattended RFDS base, a tone will be transmitted automatically...
Page 143: Telstra Radphone Service
RFDS and Telstra services Telstra Radphone Service Telstra Mobile Satellite and Radio Services (formerly OTC maritime) provide the Radiophone user with the ability to access the public switched telephone network (PSTN) at any time of the day or night. This brings the convenience of home or office to the outback traveller through the radio telephone facility of your Radiophone and the Telstra organisation.
Page 144: Transmitting A Telstra (Otc) Selective Call-Selcall
RFDS and Telstra services Transmitting a Telstra (OTC) selective call—Selcall This procedure explains how to contact a Telstra station selectively to initiate a telephone call through the Telstra Radphone operator using the ‘Radphone Selcall’ and ‘Radphone’ services. Registered users of the ‘Radphone Direct Dial’ service will receive a separate user guide detailing the operating requirements of that service.
Page 145 RFDS and Telstra services Step Action… Display shows… Remarks… Press A table of all the Telstra station selcall address S’Call numbers is shown on page 10-9. and then press Select Channel until the required selective call address appears against the Telstra station selected.
Page 146 RFDS and Telstra services Note: if the call is not successful, either the channel chosen is not a monitored, or selcall, channel for the Telstra station called, or the frequency is not appropriate for the time of day and range you are working. Check the channel frequencies listing for the station being called, if necessary choose another channel.
Page 147: Transmitting A Telstra Selective Beacon Call
RFDS and Telstra services Transmitting a Telstra selective beacon call The beacon facility is used to check signal conditions between your Radiophone and a selected Telstra station. Step Action… Display shows… Remarks… Ensure your The last channel selected. Radiophone is switched on.
Page 148 RFDS and Telstra services Step Action… Display shows… Remarks… Check that the The transmit indicator channel is free will be lit and you will from traffic, then hear a warbling sound for press approximately 10 seconds. If the call is Tune Immediately the call is successfully decoded you...
Page 149: Receiving A Telstra Selective Call
RFDS and Telstra services Receiving a Telstra selective call This procedure explains how a telephone call is received on your Radiophone through Telstra from the public telephone service. It should be noted that telephone subscribers can book a radio–telephone call to you by dialling the national Telstra booking number 0108.
Page 150 RFDS and Telstra services Notes If you do not answer the call immediately, once the call is stored in cont. memory your Radiophone will continue to give out ’pips’ every four seconds to indicate that a call has been received. If you wish to silence these ’pips’, yet still retain the display, press the Selective Channel button.
Page 151: Transmitting A Telstra (Otc) Tone Call
RFDS and Telstra services Transmitting a Telstra (OTC) tone call The tone call facility allows you to call a Telstra station using the transmission of a simple signalling system–OTC tone call. It should be noted that whilst the tone call facility is available it is recommended that, where ever possible, all calls to Telstra are initiated by the selective call procedure—the preferred method of establishing contact.
Page 152: Changing The Set-Up Options
Some of the set-up options in this section can be completed by the user, others must only be carried out by qualified personnel, either at the Codan factory or by a Codan agent. A statement is made in the procedure whenever qualified personnel are required.
Page 153: The Control Head Link
Changing the set-up options The control head link The control head link is located on the control head printed circuit board (PCB) assembly (part number 08-04666-001). The PCB is located inside the control head. The link is located on a row of four vertically mounted pins on the PCB (figure 11.1), immediately behind the number 7 button.
Page 154: Changing The Position Of The Control Head Link
Changing the set-up options Changing the position of the control head link The control head link is a black plastic moulding incorporating linked metal contacts. The contacts short together pins located on the control head PCB. Extreme care should be taken when handling the control head to prevent damage to the components.
Page 155: The Microprocessor Pcb Link
Changing the set-up options The microprocessor PCB link The microprocessor link is one that you will have to make and solder on the microprocessor PCB. The PCB (part number 08- 03741-001) is positioned on the underside of the transceiver. The link must only be soldered across the number 2 pads as shown in figure 11.2.
Page 156: Inserting The Microprocessor Pcb Link
Changing the set-up options Inserting the microprocessor PCB link Extreme care should be taken when handling the transceiver to prevent damage to the components. This procedure must only be carried out by a qualified technician. Step Action Turn the Radiophone off and disconnect the power. Lay the transceiver on its top with the front panel facing you.
Page 157: Reviewing Set-Up Options
Changing the set-up options Reviewing set-up options This facility allows you to see what set-up options have been enabled with the Radiophone. You can review the set-up options at any time. Step Action… Display shows… Remarks… Ensure your No display. Radiophone is off.
Page 158 Changing the set-up options Step Action… Display shows… Remarks… To exit the review mode and resume normal operations, press the PTT button. Outback HF Radiophone 11-7...
Page 159: Ptt Timer
Changing the set-up options PTT timer This facility stops the Radiophone from being left on in the transmit state. If the transmit time exceeds the PTT timer setting, the Radiophone reverts to the receive mode and an error message is displayed. The timer is set at the factory to 10 minutes.
Page 160 Changing the set-up options Step Action… Display shows… Remarks… Press No display. Your selection has been made and the On/Off Radiophone is now switched off. Return the control Refer to the procedure on head link to its page 11-3. original position (E).
Page 161: Enter A Pin (Personal Identification Number)
Changing the set-up options Enter a PIN (Personal Identification Number) If you select a PIN for the Radiophone, you will have to enter this PIN each time you switch the Radiophone on. If you fail to enter the correct PIN, the Radiophone will automatically switch off.
Page 162 Changing the set-up options Step Action… Display shows… Remarks… Press Your PIN number has now been registered Enter within the Radiophone. Press No display. The Radiophone is now switched off. On/Off Return the control Refer to the procedure on head link to its page 11-3.
Page 163: Changing Or Deleting A Pin
Changing the set-up options Changing or deleting a PIN This procedure allows you to change your PIN, or delete it. Step Action… Display shows… Remarks… Turn the No display. Refer to the procedure on Radiophone off page 11-3. and move the control head link from position E to position 1.
Page 164 Changing the set-up options To insert a new The display will show the You can select a number PIN, use the number you enter, or if between 1 and 999999. numeric buttons you cleared the PIN and press A new PIN is now Enter registered, or the old PIN has been cleared.
Page 165: Power-On Settings
Changing the set-up options Power-on settings There are two power-on settings that may be set at any time without the need to move or install any internal links. These are the default settings that will always be present when you switch on the Radiophone. •...
Page 166 Changing the set-up options Step Action… Display shows… Remarks… To select S’Call No change in the display. The S’Call Mute is on Mute on, press when the indicator is lit. S’Call Mute to select S’Call Mute off press Voice Mute Press Reverts to normal display Your selection has been...
Page 167: Beep Volume
Changing the set-up options Beep volume Step Action… Display shows… Remarks… Hold down Hold down either of the This switches your volume buttons until the Radiophone on and into display shows the beep volume set-up mode. The display will show the last beep volume setting.
Page 168: Clear All Settings And P-Channels
Changing the set-up options Clear all settings and P-channels This facility allows you to clear all settings (except the PIN number) and P-channels automatically. Ensure your Radiophone is switched off before commencing this procedure. Do NOT use this facility if you require any of the P-channels. To restore the transmit frequencies may be extremely difficult.
Page 169 Changing the set-up options 11-18 Outback HF Radiophone...
Page 170: Display Messages
If a Radiophone fault is indicated, the Radiophone must be switched off and tried again. If the fault re-occurs the Radiophone must be sent to Codan, or a Codan agent, to have the fault rectified. Messages will be displayed for five seconds and then normal operation will be resumed.
Page 171: Messages And Operator Errors
Display messages Messages and operator errors No. of ’beeps’ Message displayed Meaning The automatic antenna has been satisfactorily tuned. The automatic antenna has failed to tune. An attempt has been made to transmit before the automatic antenna has been tuned. Wait until the automatic antenna has tuned.
Page 172 Display messages No. of ’beeps’ Message displayed Meaning An attempt has been made to transmit on a receive-only channel, or while the scan mode is selected. If the Radiophone is scanning, press the Scan button to stop scanning. If the channel selected is a receive-only channel, select another channel.
Page 173: Setting Up The P-Channel Inhibit Options
Display messages No. of ’beeps’ Message displayed Meaning The nominated channel is already programmed. There are four program inhibit options available. Refer to Setting up the P-channel inhibit options in section 7. An emergency call, tone call or a selective call has been attempted on a channel where that function has not been enabled.
Page 174 Display messages No. of ’beeps’ Message displayed Meaning The telephone mode is on. A request for you to enter a telephone number. A request for you to enter a code number for a particular telephone number. A request for you to enter a telephone number that you want to delete from memory.
Page 175 Display messages No. of ’beeps’ Message displayed Meaning A call has been received on another channel. Display shows call on channel 400 and frequencies. An ARQ call has been received. In this example, on channel P2 the frequency is 12.340 MHz. Indicates that no telephone numbers have been stored.
Page 176: System Errors
Display messages System errors No. of ’beeps’ Message displayed Meaning Internal synthesiser is unlocked. All transmission is inhibited and the receiver is muted. Turn the Radiophone off and then try again. If the problem persists, the Radiophone must be returned for service.
Page 177: Reviewing The Eprom Program Content
Display messages Reviewing the EPROM program content With the Radiophone on, push and hold the On/Off button. The display will show the following test displays at three second intervals. On releasing the On/Off button the Radiophone is turned off. No. of ’beeps’ Message displayed Meaning Display lamp test: all segments must...
Page 178 Display messages No. of ’beeps’ Message displayed Meaning These displays indicate some of the options fitted to the Radiophone. d indicates that the Radiophone is inhibited from entering transmit frequencies from the front panel. A indicates that the Radiophone is programmed for use on the amateur band.
Page 179 Display messages 12-10 Outback HF Radiophone...
Page 180: Front And Rear Panel Sockets
13. Front and rear panel sockets Only suitably qualified personnel should use the information contained in this section. Failure to observe the stated and implied criteria could result in damage to the Radiophone. Details are provided on the following sockets: •...
Page 181: Microphone Socket
Front and rear panel sockets Microphone socket This socket is located on the front panel of the control head. It is used to connect the microphone to the Radiophone. Front panel view 4 5 6 7 1 2 3 Pin No. Designation Pin No.
Page 182: External Alarm Socket
Front and rear panel sockets External alarm socket This socket is located on the rear panel of the transceiver. This facility allows an external alarm device to be connected to the Radiophone. When a selective call is detected, internal relay contacts close across pins 2 & 3. The contacts are rated for 1A at 50V DC.
Page 183: Antenna Control Socket
Front and rear panel sockets Antenna control socket This socket is located on the rear panel of the transceiver and accepts the plug from the automatic tuning whip antenna. A warning label above the antenna control socket indicates WARNING 8558 CONNECT TO ONLY Pin No.
Page 184: Remote Control Socket
Front and rear panel sockets Remote control socket This socket allows the remote control head to be connected to the Radiophone. Pin No. Designation Pin No. Designation Loudspeaker Ground Remote PTT (active low) Ground Receiver audio input * Transmit audio input (1.5V pp) Power on (active low, pulse) Receiver demodulator...
Page 185 Front and rear panel sockets 13-6 Outback HF Radiophone...
Page 186: Specification
14. Specification Frequency range Transmit: 2 to 24 MHz (CB: 27 MHz) Receive: 250 kHz to 30 MHz Channel capacity 600. Comprising 501 pre-programmed EPROM controlled channels and 99 front panel, user programmable channels. Transmitted power 100 watts PEP (CB: 12 watts PEP) output CB operation 27 MHz, 40 channels...
Page 187 Specification 14-2 Outback HF Radiophone...
Page 188: Options And Accessories
15. Options and accessories The following options and accessories are available for the Radiophone. Code Options Fit amateur band transmit-receive facility (for licensed amateur radio operators). Fit for continuous data transmission. Fit unswitched battery power output facility. Bulkhead mounting fuse holder for transceiver DC power cord - supplied with 32 amp fuse.
Page 189 Options and accessories 15-2 Outback HF Radiophone...

This manual is also suitable for:

8528 series

Codan 8525B Series Handbook

1 About this Handbook

2 Overview

3 Installation

4 Using the Radiophone

5 Using Selective Call

6 Using the Receiver in Scan Mode

7 Programming Channels

8 Using Tone Call

9 Making a Telephone Interconnect Call

10 RFDS and Telstra Services

11 Changing the Set-Up Options

12 Display Messages

13 Front and Rear Panel Sockets

14 Specification

15 Options and Accessories

Quick Links

Need help?

Questions and answers

Related Manuals for Codan 8525B Series

Summary of Contents for Codan 8525B Series

This manual is also suitable for:

Table of Contents