Group 03: Actual Signals - Daikin ACS320 Operation Manual

Code Description (continuation of Table 23)
0177 SAVED AMOUNT 2
Energy saved in local currency in thousand currency units . Eg value 5 means 5000 currency units . See parameter 0176 SAVED AMOUNT 1 .
Local energy price is set with parameter 4502 ENERGY PRICE . Can be reset with parameter 4509 ENERGY RESET (resets all energy calculators at the same time) .
See Group 45 ENERGY SAVING,
0178 SAVED CO
2
Reduction on carbon dioxide emissions in tn . CO
(resets all energy calculators at the same time) . See Group 45 ENERGY SAVING,

Group 03: Actual Signals

This group monitors fieldbus communications.
Table 24: Group 03: Actual Signals
Code Description
0301 FB CMD WORD 1
Read-only copy of the Fieldbus Command Word 1 .
• The fieldbus command is the principal means for controlling the drive from a fieldbus controller. The command consists of two Command Words. Bit-coded instructions in the
Command Words switch the drive between states .
• To control the drive, using the Command Words, an external location (EXT1 or EXT2) must be active and set to COMM . (See parameters 1001 and 1002 .)
• The control panel displays the word in hex . For example, all zeros and a 1 in Bit 0 displays as 0001 . All zeros and a 1 in BIt 15 displays as 8000 .
Bit # 0301, fb cmd word 1
0 STOP
1 START
2 REVERSE
3 LOCAL
4 RESET
5 EXT2
6 RUN_DISABLE
7 STPMODE_R
0302 FB CMD WORD 2
Read-only copy of the Fieldbus Command Word 2 .
• See parameter 0301, page 35 .
0303 FB STS WORD 1
Read-only copy of the Status Word 1 .
• The drive sends status information to the fieldbus controller. The status consists of two Status Words.
Bit # 0303, sts cmd word 1 0304, fb sts word 2
0 READY
1 ENABLED
2 STARTED
3 RUNNING
4 ZERO_SPEED
5 ACCELERATE
6 DECELERATE
7 AT_SETPOINT
0304 FB STS WORD 2
Read-only copy of the Status Word 2 .
• See parameter 0303, page 35 .
0305 FAULT WORD 1
Read-only copy of the Fault Word 1 .
• When a fault is active, the corresponding bit for the active fault is set in the Fault Words .
• Each fault has a dedicated bit allocated within Fault Words .
• See Fault Tracing, page 90 for a description of the faults .
The control panel displays the word in hex . For example, all zeros and a 1 in Bit 0 displays a 0001 . All zeros and a 1 in Bit 15 displays as 8000 .
Bit # 0305,fault word 1
0 OVERCURRENT
1 DC OVERVOLT
2 DEV OVERTEMP
3 SHORT CIRC
4 Reserved
5 DC UNDERVOLT
6 AI1 LOSS
7 AI2 LOSS
0306 FAULT WORD 2
A16-bit data word. For the possible causes and remedies and fieldbus equivalents, see Fault Tracing,
Bit #
0 Reserved
1 THERM FAIL
2 . . .3 Reserved
4 CURR MEAS
5 SUPPLY PHASE
www .DaikinApplied .com
page 66 .
conversion factor is set with parameter 4507 CO
2
0302, fb cmd word 2 Bit # 0301, fb cmd word 1
FBLOCAL_CTL 8 STPMODE_EM
FBLOCAL_REF 9 STPMODE_C
START_DISABLE1 10 RAMP_2
START_DISABLE2 11 RAMP_OUT_0
Reserved 12 RAMP_HOLD
Reserved 13 RAMP_IN_0
Reserved 14 RREQ_LOCALLOC
Reserved 15 TORQLIM2
Bit # 0303, sts cmd word 1
ALARM 8 LIMIT
REQ_MAINT 9 SUPERVISION
DIRLOCK 10 REV_REF
LOCALLOCK 11 REV_ACT
CTL_MODE 12 PANEL_LOCAL
Reserved 13 FIELDBUS_LOCAL
Reserved 14 EXT2_ACT
Reserved 15 FAULT ACK_
0306 fault word 2 0307 fault word 3
UNDERLOAD EFB 1
THERM FAIL EFB 2
OPEX LINK EFB 3
OPEX PWR Incompatible software type
CURR MEAS Reserved
SUPPLY PHASE Reserved
ENCODER ERROR Reserved
OVERSPEED Reserved
Bit #
6 Reserved
7 OVERSPEED
8 Reserved
9 DRIVE ID
10 CONFIG FILE
CONV FACTOR . Can be reset with parameter 4509 ENERGY RESET
2
page 66 .
0302, fb cmd word 2
Reserved
Reserved
Reserved
REF_CONST
REF_AVE
LINK_ON
REQ_STARTINH
OFF_INTERLOCK
0304, fb sts word 2
Reserved
Reserved
REQ_CTL
REQ_REF1
REQ_REF2
REQ_REF2EXT
ACK_STARTINH
OFF_ILCK
Bit # 0305, fault word 1 0306, fault word 2
8 MOT OVERTEMP Reserved
9 PANEL LOSS DRIVE ID
10 ID RUN FAIL CONFIG FILE
11 MOTOR STALL SERIAL 1 ERR
12 Reserved EFB CON FILE
13 EXT FLT 1 FORCE TRIP
14 EXT FLT 2 MOTOR PHASE
15 EARTH FAULT OUTPUT WIRING
page 90 .
Bit #
11 SERIAL 1 ERR
12 EFB CON FILE
13 FORCE TRIP
14 MOTOR PHASE
15 OUTP WIRING
35
a s p
CTual Ignals and arameTers
Range Resolution Default
1 = 1000
— —
(Currency)
— 1 = 0 .1 tn —
Range Resolution Default
— — —
— — —
— 1 - hex
— 1 - hex
— 1 0000 hex
0307, fault word 3
Reserved
Reserved
System Error
System Error
System Error
System Error
Hardware Error
Param . Setting Fault
- 1 0000 hex
OM 1190-1 • MD4 VFD
S
S