Panasonic AFPX-C30R User Manual page 516

Num-
Name
ber
F150 Data read from
P150 intelligent unit
F151 Data write into
P151 intelligent unit
F152 Data read from
P152 MEWNET-F
slave station
F153 Data write into
P153 MEWNET-F
slave station
F155 Sampling
P155
F156 Sampling
P156 trigger
F157 Time addition
P157
F158 Time
P158 subtraction
F159 Serial port
P159 communication
F161 MCU serial port
P161 reception
BIN arithmetic instruction
F160 Double word
P160 (32-bit) data
square root
High speed counter/Pulse output instruction for FP0, FP-e
F0 High-speed
counter and
Pulse output
controls
1 Change and
read of the
elapsed value
of high-speed
counter and
Pulse output
F166 High-speed
counter output
set (with
channel
specification)
: Available, : Not available,
*1) The instruction is available for FP0 T32 (V2.3 or later) and FP-e.
*2) The instruction is available for FP2/FP2SH Ver. 1.5 or later, and the pulse execution type can be specified.
FP10SH cannot be used.
*3) This instruction is available for FPΣ Ver. 2.0 or later.
*4) This instruction is only available for FP-X Ver.2.0 or later.
*5) This instruction is available for FPΣ Ver. 3.10 or later.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Ope-
Boolean
rand
S1, S2, Reads the data from the
READ
n, D intelligent unit.
PREAD
S1, S2, Writes the data into the intelligent
WRT
n, D unit.
PWRT
S1, S2, Reads the data from the
RMRD
n, D intelligent unit at the MEWNET-F
PRMRD
(remote I/O) slave station.
S1, S2, Writes the data into the intelligent
RMWT
n, D unit at the MEWNET-F (remote
PRMWT
I/O) slave station.
- Starts sampling data.
SMPL
PSMPL
- When the trigger of this
STRG
instruction turns on, the sampling
PSTRG
trace stops.
S1, S2, The time after (S2+1, S2)
CADD
D elapses from the time of (S1+2,
PCADD
S1+1, S1) is stored in (D+2, D+1,
D).
S1, S2, The time that results from
CSUB
D subtracting (S2+1, S2) from the
PCSUB
time (S1+2, S1+1, S1) is stored
in (D+2, D+1, D).
S, n, D This is used to send data to an
MTRN
external device through the
PMTRN
specified CPU COM port or MCU
COM port.
S, D 1, Data is received from external
MRCV
D2 equipment via the COM port of
PMRCV
the specified MCU.
S, D
DSQR
√(S)→(D)
PDSQR
S, Performs high-speed counter and
MV
DT9052 Pulse output controls according
to the control code specified by
"S". The control code is stored in
DT9052.
S, Transfers (S+1, S) to high-speed
DMV
DT9044 counter and Pulse output elapsed
value area.
DT9044, Transfers value in high-speed
D counter and Pulse output elapsed
value area to (D+1, D).
n, S, Yn Turns output Yn on when the
HC1S
elapsed v alue of the built-in high-
speed counter reaches the target
value of (S+1, S).
: Not available partially
Description
9
9
9
9
1
1
9
9
7
7
7
5
7
7
11
*3
*3
*5 *4
*5 *4
*1
*1
*2 *2
*2 *2