Page 1 2560 Barcode Scanner Setup barcodes included. Version 1.00...
Page 2 Due to continued product development this information may change without notice. The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find any problems in the documentation, please report them to us in writing.
Page 3: Important Notices
IMPORTANT NOTICES FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 4: For Hand-Held Product With Rf Functions
FOR HAND-HELD PRODUCT WITH RF FUNCTIONS The 2560 unit (FCC ID: Q3N-2560) complies with FCC radiation exposure limits set forth for uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. The unit has very low level of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR).
Page 5: Release Notes
RELEASE NOTES Version Date Notes  Initial release (based on 1560/1562; the Product with Laser notice 1.00 Jan. 05, 2017 removed)  Modified: 2.3.1 – a single 1D barcode (SeTcOn) for connecting to a target device added New: 2.7.2 Activate USB Virtual COM_CDC ...
Page 6 CONTENTS IMPORTANT NOTICES ......................- 3 - For USA............................- 3 - For Canada ..........................- 3 - For Hand-held Product with RF Functions ..............- 4 - Safety Precautions ........................- 4 - Care & Maintenance........................ - 4 - RELEASE NOTES ........................
Page 7 2560 Series Barcode Scanner User Guide 1.3.1 Good Read LED ......................33 1.3.2 Good Read LED Duration ..................33 1.4 Beeper ............................ 34 1.4.1 Beeper Volume ......................35 1.4.2 Good Read Beep ....................... 36 1.4.3 Low Battery Alarm ....................37 1.5 Send “NR”...
Page 8 2560 Series Barcode Scanner User Guide 2.3.1 Activate BT SPP Master Mode ................69 2.3.2 Inter-Function Delay ....................71 2.3.3 ACK/NAK Timeout ....................71 2.3.4 Switch between Master/Slave Mode ..............73 2.3.5 BT SPP Master Hardware Flow Control ............. 73 2.3.6 BT SPP Master Auto-Reconnection ..............
Page 9 2560 Series Barcode Scanner User Guide 4.1.3 CLSI Conversion ...................... 119 4.1.4 Security Level ......................119 4.2 Code 25 – Industrial 25 ....................120 4.2.1 Start/Stop Pattern Selection ................120 4.2.2 Verify Check Digit ....................121 4.2.3 Transmit Check Digit ..................... 121 4.2.4 Code Length Qualification ...................
Page 10 2560 Series Barcode Scanner User Guide 4.12.3 Code Length Qualification ................. 141 4.13 French Pharmacode ...................... 142 4.13.1 Transmit Check Digit ..................142 4.14 Italian Pharmacode ...................... 143 4.14.1 Transmit Check Digit ..................143 4.15 Plessey ..........................144 4.15.1 Convert to UK Plessey ..................144 4.15.2 Transmit Check Digit ..................
Page 11 2560 Series Barcode Scanner User Guide APPLYING FORMATS FOR DATA EDITING .............. 181 6.1 Activating Editing Formats ................... 182 6.1.1 Activate Editing Formats ..................182 6.1.2 Exclusive Data Editing ..................183 6.2 How to Configure Editing Formats ................184 6.2.1 Select Format to Configure ................. 185 6.2.2 Restore Default Format ..................
Page 12 2560 Series Barcode Scanner User Guide Entering PIN Code for Authentication ................230 Use Preset PIN ........................230 Disable Authentication or Use Random PIN ............. 231 KEYBOARD TYPE ONE-SCAN BARCODE ..............233 Keyboard Wedge ........................233 Bluetooth HID ........................... 237...
Page 13: Introduction
INTRODUCTION CipherLab’s barcode scanners are specifically designed to answer your mobile demands. The versatile scanners are designed to help accelerate productivity while lowering the total cost of ownership. Intensive data collection jobs are made easier with fast, accurate barcode scanning in various working environments, especially in small businesses.
Page 14: Getting Familiarized With The Scanner And The Cradle
2560 Series Barcode Scanner User Guide GETTING FAMILIARIZED WITH THE SCANNER AND THE CRADLE INSTALLING THE BATTERY TO THE SCANNER When you first receive the package, the rechargeable battery is stored separately from the scanner. Insert the battery into the scanner first so that it can be charged when sitting in the cradle.
Page 15: Setting Up The Cradle
Introduction SETTING UP THE CRADLE Capable of charging the scanner, the cradle is specifically designed for the scanner to communicate with a host computer wirelessly. Refer to 3.1.1 Connect to Cradle. Two LED indicators are provided for power and communications status. Power LED Meaning Red,...
Page 16 2560 Series Barcode Scanner User Guide flashing Red, Blue, Failed to send data to host via USB Virtual COM (Fast flash at 1 Hz) solid flashing Red, Enter Download Mode flashing Enter Setup...
Page 17: Charging The Battery Via The Cradle
Introduction CHARGING THE BATTERY VIA THE CRADLE The battery may not be charged to full for shipment. When you first receive the package, you will need to charge the battery to full before using the scanner. When using the RS-232 cable, it takes approximately 5 hours to charge the battery to full (from the power adaptor).
Page 18: Charging The Battery Via Charger
2560 Series Barcode Scanner User Guide CHARGING THE BATTERY VIA CHARGER The battery charger is provided for charging the battery only. You may purchase the charger separately. It takes approximately 3 hours to charge the battery to full. Note: Battery charging stops when the temperature drops below 0°C or exceeds 40°C. It is recommended to charge the battery at room temperature (18°C to 25°C) for...
Page 19: Inside The Package
Introduction INSIDE THE PACKAGE The items included in the package may be different, depending on your order. Save the box and packaging material for future use in case you need to store or ship the scanner. Barcode Scanner  BT Base ...
Page 20: Symbologies Supported
2560 Series Barcode Scanner User Guide SYMBOLOGIES SUPPORTED Most of the popular barcode symbologies are supported, as listed below. Each can be individually enabled or disabled. The scanner will automatically discriminate and recognize all the symbologies that are enabled. Refer to...
Page 21 Introduction GS1 DataBar Stacked Omnidirectional Disabled GS1 DataBar Limited (RSS Limited) Disabled GS1 DataBar Expanded (RSS Expanded) Disabled GS1 DataBar Expanded Stacked Disabled Update...
Page 22 2560 Series Barcode Scanner User Guide Enter Setup...
Page 23: Quick Start
QUICK START The configuration of the scanner can be done by reading the setup barcodes contained in this manual or via the ScanMaster software. This section describes the procedure of configuring the scanner by reading the setup barcodes and provides some examples for demonstration. Configuration Mode Hold down the trigger about 2 seconds to turn on the scanner.
Page 24 2560 Series Barcode Scanner User Guide Working Mode Upon powering up, the scanner will try to establish a connection with the BT cradle or a computer ® with Bluetooth wireless technology. Refer to Chapter 3 – Setting up a WPAN Connection details.
Page 25: Enter Configuration Mode
Quick Start ENTER CONFIGURATION MODE For the scanner to enter the configuration mode, you must have it read the “Enter Setup” barcode, which can be located at the bottom of almost every even page of this manual. The scanner will respond with six beeps and its LED indicator will become flashing red ...
Page 26: Default Settings
2560 Series Barcode Scanner User Guide DEFAULT SETTINGS SAVE USER SETTINGS AS DEFAULTS For the scanner to keep the customized settings as user defaults, you must have it read the “Save as User Defaults” barcode. This is a normal setup barcode, and the scanner will respond with two beeps (low-high tone).
Page 27: Read A Setup Barcode
Quick Start READ A SETUP BARCODE CONFIGURE PARAMETERS For most of the scanner parameters, only one read is required to set them to new values. The scanner will respond with two beeps (low-high tone) when each parameter is set successfully. But for a number of special parameters, multiple reads are required to complete the setting.
Page 28 2560 Series Barcode Scanner User Guide The example below shows how to save your settings as “User Default” so that you may restore user defaults at a later time: Steps Action User Feedback if Successful Power on the scanner… The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly.
Page 29 Quick Start The example below shows how to set numeric parameters: Steps Action User Feedback if Successful Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly. Enter the Configuration Mode…...
Page 30 2560 Series Barcode Scanner User Guide The example below shows how to set string parameters: Steps Action User Feedback if Successful Power on the scanner... The scanner will respond with a long beep (high tone) and its LED indicator will become solid red and go off quickly.
Page 31: List The Current Settings
Quick Start LIST THE CURRENT SETTINGS The current settings of all scanner parameters can be sent to the host computer for user inspection. The listing includes pages as shown below. You can select the page of interest by having the scanner read the “List Page x” barcode. The scanner will respond with two beeps (low-high tone) and send the selected page to the host immediately.
Page 32 2560 Series Barcode Scanner User Guide List settings regarding Editing Format 4 List Page 11 List settings regarding Editing Format 5 List Page 12 Enter Setup...
Page 33: Create One-Scan Setup Barcodes
Quick Start CREATE ONE-SCAN SETUP BARCODES The fact is most of the scanner parameters require only one read for setting new values. To facilitate configuring the scanner, you may create One-Scan setup barcodes for use. The requirements of a One-Scan setup barcode are: a prefix of the “#@”...
Page 34 2560 Series Barcode Scanner User Guide Enter Setup...
Page 35: Understanding The Barcode Scanner
Chapter 1 UNDERSTANDING THE BARCODE SCANNER This chapter will guide you through the features of the barcode scanner and how it can function for you. IN THIS CHAPTER 1.1 Battery ..............23 1.2 Memory ..............29 1.3 LED Indicator ............. 32 1.4 Beeper...............
Page 36: Power Economy
2560 Series Barcode Scanner User Guide 1.1.2 POWER ECONOMY The scanner features “Power-Saving”, “Auto Power Off” and “Auto Power Off Ignoring Scan Mode” giving consideration to the power issue that is generally critical for Bluetooth-enabled devices. By the scanner’s support of power economy, its power...
Page 37 Chapter 1 Understanding the Barcode Scanner Note: Power-Saving won’t take effect when one of the following conditions is met: (1) the scanner has already established a BT HID/SPP connection, (2) the scanner is in the configuration mode, (3) the scan mode is set to Test, Continuous or Alternate Mode, or (4) the setting value of Power-Saving is greater than that of Auto Power Off.
Page 38 2560 Series Barcode Scanner User Guide Note: “Auto Power Off” will not take effect when the scanner is in the configuration modee. 1.1.2.3 AUTO POWER OFF IGNORING SCAN MODE This mode is intended only for Continuous Mode, Test Mode, and Alternate Mode. To...
Page 39: Power Economy Vs. Wpan Connection
Chapter 1 Understanding the Barcode Scanner 1.1.3 POWER ECONOMY VS. WPAN CONNECTION Before the scanner can communicate with the host computer, Bluetooth connection (or WPAN connection) needs to be established. The scanner’s power economy always accommodates itself to the establishment of the WPAN connection. The following describes how the scanner carries out power economy before and after the establishment of the WPAN connection: Before establishing a WPAN connection successfully…...
Page 40 2560 Series Barcode Scanner User Guide from low to high upon the resumption. If the scanner fails to resume the connection, it will try every 5 seconds to re-connect to the host unless you have the scanner read the “Reset Connection”...
Page 41: Memory
Chapter 1 Understanding the Barcode Scanner 1.2 MEMORY The collected data can be sent back to a host computer one by one via the WPAN connection or stored in flash memory when the scanner is set to Memory mode. 1.2.1 TRANSMIT BUFFER By default, transmit buffer is enabled and for use when the scanner is out of range.
Page 42: Memory Mode
2560 Series Barcode Scanner User Guide 1.2.2 MEMORY MODE The scanner uses flash memory for memory mode operation. When the scanner is in memory mode, it means any real-time connection established with the host is disabled. Enable *Disable Warning: No real-time connection is allowed unless the memory mode is disabled.
Page 43: Free Memory
Chapter 1 Understanding the Barcode Scanner 8 sec Send Data The 4MB flash memory on the scanner can store up to 240,000 scans based on EAN-13 barcodes. When it is used up, the scanner will respond with two short beeps (high-low tone) as a warning. You are advised to send data to the host immediately by having the scanner read the “Send Data”...
Page 44: Led Indicator
2560 Series Barcode Scanner User Guide 1.3 LED INDICATOR The triple-color LED on top of the scanner is used to provide user feedback. For example, the LED becomes solid red and goes off quickly upon powering on or running out of transmit buffer.
Page 45: Good Read Led
Chapter 1 Understanding the Barcode Scanner 1.3.1 GOOD READ LED *Enable Good Read LED Disable Good Read LED 1.3.2 GOOD READ LED DURATION By default, the Good Read LED stays on for 40 milliseconds. Specify a value, ranging from 1 to 254 in units of 10 milliseconds. Good Read LED Time-out after 0.01~2.54 sec.
Page 46: Beeper
2560 Series Barcode Scanner User Guide 1.4 BEEPER The scanner has a buzzer to provide user feedback in various operating conditions. Beeping Meaning One long beep, high tone Power on, with red LED on (1 second) and off quickly One short beep, high tone Good Read, with green LED on-off quickly ...
Page 47: Beeper Volume
Chapter 1 Understanding the Barcode Scanner 1.4.1 BEEPER VOLUME Mute Minimum Volume Medium Volume *Maximum Volume Update...
Page 48: Good Read Beep
2560 Series Barcode Scanner User Guide 1.4.2 GOOD READ BEEP Frequency 8 kHz *4 kHz 2 kHz 1 kHz Duration *Shortest Shorter Longer Longest Enter Setup...
Page 49: Low Battery Alarm
Chapter 1 Understanding the Barcode Scanner 1.4.3 LOW BATTERY ALARM By default, it will activate the beeper to give a warning when the battery charge gets low. In order to prevent data loss, you are advised to replace the battery immediately when you hear two short beeps (high tone).
Page 50: Scan Modes
2560 Series Barcode Scanner User Guide 1.6 SCAN MODES Different scan modes are supported – select the scan mode that best suits the requirements of a specific application. Refer to the comparison table below. Scan Mode Start to Scan Stop Scanning...
Page 51: Continuous Mode
Chapter 1 Understanding the Barcode Scanner 1.6.1 CONTINUOUS MODE The scanner is always scanning. After a successful decoding, the removal of barcode is required. It is not allowed to  proceed to decode until the decoding delay time has passed. To decode the same barcode repeatedly, move away the barcode and put it back ...
Page 52: Laser Mode
2560 Series Barcode Scanner User Guide 1.6.3 LASER MODE The scanner will start scanning once the trigger is held down. The scanning won’t stop until (1) a barcode is decoded, (2) the pre-set timeout  expires, or (3) you release the trigger.
Page 53: Alternate Mode
Chapter 1 Understanding the Barcode Scanner 1.6.6 ALTERNATE MODE The scanner will start scanning once the trigger is pressed The scanning won't stop until you press the trigger again.  Alternate Mode 1.6.7 AIMING MODE The scanner will aim at a barcode once the trigger is pressed, and start scanning when the trigger is pressed again within one second.
Page 54: Multi-Barcode Mode
2560 Series Barcode Scanner User Guide 1.6.8 MULTI-BARCODE MODE The scanner will be scanning as long as the trigger is held down, capable of decoding one single barcode, as well as multiple unique barcodes one at a time. While decoding a bunch of unique barcodes, if a barcode is decoded twice, its subsequent decoding will be ignored and the scanner is expecting another unique barcode.
Page 55: Scanning Timeout
Chapter 1 Understanding the Barcode Scanner 1.7 SCANNING TIMEOUT Specify the scanning time interval (1~254 sec.; 0= Disable) when the scan mode is set to any of the following – Laser mode  Auto Off mode  Auto Power Off mode ...
Page 56: Delay Between Re-Read
2560 Series Barcode Scanner User Guide 1.8 DELAY BETWEEN RE-READ This is also referred to as the “Blocking Time”, which is used to prevent the scanner from accidentally reading the same barcode twice when the scan mode is set to any of the following –...
Page 57: Read Redundancy For All Symblogies
Chapter 1 Understanding the Barcode Scanner 1.9 READ REDUNDANCY FOR ALL SYMBLOGIES Select the level of reading security. For example, If “No Redundancy” is selected, one successful decoding will make the reading valid  and induce the “READER Event”. If “Three Times” is selected, it will take a total of four consecutive successful ...
Page 58: Addon Security For Upc/Ean Barcodes
2560 Series Barcode Scanner User Guide 1.10 ADDON SECURITY FOR UPC/EAN BARCODES The scanner is capable of decoding a mix of UPC/EAN barcodes with and without addons. The read redundancy (0~30 times) allows changing the number of times to decode a UPC/EAN barcode before transmission.
Page 59: Auto-Sense Mode
Chapter 1 Understanding the Barcode Scanner 1.11 AUTO-SENSE MODE Auto-sense is only available when the scanner is working in Laser Mode. The scanner will be expecting barcodes as long as it is seated in the Auto-sense stand. Whenever a barcode is brought within range, the scanner will be able to decode it. To stop this mode, just remove the scanner from the stand.
Page 60: Ambient Light
2560 Series Barcode Scanner User Guide 1.11.3 AMBIENT LIGHT When the ambient light is too dim to activate the sensor, you may have the scanner read the “High Sensitivity” barcode to improve performance. It will emit scan beam every 300 milliseconds when “High Sensitivity”...
Page 61: Negative Barcodes
Chapter 1 Understanding the Barcode Scanner Disable 1.13 NEGATIVE BARCODES Normally, barcodes are printed with the color of the bars darker than that of the spaces. But for negative barcodes, they are printed in the opposite sense just like negative films. The spaces of negative barcodes are printed with a color darker than that of the bars.
Page 62: Positioning Window
2560 Series Barcode Scanner User Guide 1.14.1 POSITIONING WINDOW Centering On *Centering Off 1.14.2 ADJUSTING WINDOW Percentage for Left Half *Left 50% Enter Setup...
Page 63 Chapter 1 Understanding the Barcode Scanner Left 40% Left 30% Left 20% Left 10% Percentage for Right Half Right 10% Right 20% Right 30% Right 40% *Right 50% Update...
Page 65: Selecting Output Interface
Chapter 2 SELECTING OUTPUT INTERFACE In order to establish a proper connection between your computer and the scanner, we suggest that you follow these instructions – 1) Install the battery and hold down the trigger for about 2 seconds to turn on the scanner.
Page 66 2560 Series Barcode Scanner User Guide 2.1 BT HID For BT HID, refer to Chapter 3 – Setting up a WPAN Connection for related connection settings. Run any text editor on your computer, and the scanned data will be transmitted to the computer.
Page 67: Activate Bt Hid & Select Keyboard Type
Chapter 2 Selecting Output Interface 2.1.1 ACTIVATE BT HID & SELECT KEYBOARD TYPE When BT HID interface is activated, you will have to select a keyboard type to complete this setting. By default, BT HID is activated on the scanner, and the keyboard type is set to PCAT (US).
Page 68: Reset Connection
2560 Series Barcode Scanner User Guide 2.1.2 RESET CONNECTION For BT HID, you can only have the scanner connected to one computer at a time. If you want to connect the scanner to another host, you must have it read the “Reset Connection”...
Page 69: Keyboard Settings
Chapter 2 Selecting Output Interface 2.1.3 KEYBOARD SETTINGS Alphabets Layout  Digits Layout  Capital Lock Type  Capital Lock Setting  Alphabets Transmission  Digits Transmission  Note: BT HID does not support these functions on PDAs – (1) Capital Lock Setting: Auto Detection (2) Digits Transmission: Numeric Key Alphabets Layout By default, the alphabets layout is set to normal mode, also known as the standard English layout.
Page 70 2560 Series Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout;...
Page 71 Chapter 2 Selecting Output Interface Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal...
Page 72 2560 Series Barcode Scanner User Guide Capital Lock Type & Setting In order to send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted.
Page 73 Chapter 2 Selecting Output Interface *Capital Lock OFF Update...
Page 74 2560 Series Barcode Scanner User Guide Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only.
Page 75 Chapter 2 Selecting Output Interface Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be “ON”.
Page 76: Inter-Character Delay
2560 Series Barcode Scanner User Guide 2.1.4 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be.
Page 77: Keypad Support For Iphone/Ipad
Chapter 2 Selecting Output Interface 2.1.7 KEYPAD SUPPORT FOR IPHONE/IPAD When the scanner has been successfully connected to iPhone or iPad for data collection, the onscreen keypad of iPhone/iPad will disappear by default. Have the scanner read the “Show or Hide Keypad” barcode to show or hide the keypad if necessary. Show or Hide Keypad Read the “Use Trigger Key to Show or Hide Keypad”...
Page 78: Bt Hid Auto-Reconnection
2560 Series Barcode Scanner User Guide Master 2.1.10 BT HID AUTO-RECONNECTION Users can decide whether to have the scanner automatically reconnect to a paired device after disconnection, and the occasion for reconnecting. *Auto reconnect immediately Auto reconnect on data being scanned...
Page 79: Bt Spp Slave
Chapter 2 Selecting Output Interface 2.2 BT SPP SLAVE For BT SPP Slave, refer to Chapter 3 – Setting up a WPAN Connection for related connection settings. 2.2.1 ACTIVATE BT SPP SLAVE MODE Read the barcode below to activate SPP Slave Mode. Activate BT SPP, Slave Mode 2.2.2 INTER-FUNCTION DELAY...
Page 80: Ack/Nak Timeout
2560 Series Barcode Scanner User Guide 2.2.3 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times.
Page 81: Bt Spp Master
Chapter 2 Selecting Output Interface 2.3 BT SPP MASTER As a SPP master device, the scanner will be able to resume connection with the host upon powering on again, as long as the host application is running. If the scanner fails to resume connection, it will try every 5 seconds to re-connect to the host unless you have the scanner read the “Reset Connection”...
Page 82 2560 Series Barcode Scanner User Guide Note: Read the “Set Connection” barcode first, and then the “MAC ID” barcode within 10 seconds. Instead of producing the “MAC ID” barcode, you may have the scanner read the setup barcodes for entering the MAC address.
Page 83: Inter-Function Delay
Chapter 2 Selecting Output Interface 2.3.2 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted.
Page 84 2560 Series Barcode Scanner User Guide ACK/NAK Error Beep Enable Error Beep *Disable Error Beep Note: We suggest enabling the error beep so that you will be notified of such data loss and have the scanner re-read data. Enter Setup...
Page 85: Switch Between Master/Slave Mode
Chapter 2 Selecting Output Interface 2.3.4 SWITCH BETWEEN MASTER/SLAVE MODE After the scanner has established a connection as a SPP slave device, you may have it read the “Activate BT SPP, Master Mode” setup barcode to switch to SPP Master Mode. This will result in easy and reliable re-connection, just like connecting with the cradle.
Page 86: Keyboard Wedge Via Bt Cradle
2560 Series Barcode Scanner User Guide 2.4 KEYBOARD WEDGE VIA BT CRADLE The Y cable allows you to connect the scanner via BT Cradle to the keyboard input port of PC and you may join the keyboard as well. The scanned data will be transmitted to the host keyboard port as if it is manually entered via the keyboard.
Page 87: Activate Keyboard Wedge & Select Keyboard Type
Chapter 2 Selecting Output Interface 2.4.1 ACTIVATE KEYBOARD WEDGE & SELECT KEYBOARD TYPE When Keyboard Wedge interface is activated, you will have to select a keyboard type to complete this setting. Activate Keyboard Wedge & Select Keyboard Type… 1) Read this barcode above to activate Keyboard Wedge and select a keyboard type. 2) Read the “Decimal Value”...
Page 88: Keyboard Settings
2560 Series Barcode Scanner User Guide 2.4.2 KEYBOARD SETTINGS Alphabets Layout  Digits Layout  Capital Lock Type  Capital Lock Setting  Alphabets Transmission  Digits Transmission  Alternate Composing  Laptop Support  Alphabets Layout By default, the alphabets layout is set to normal mode, also known as the standard English layout.
Page 89 Chapter 2 Selecting Output Interface US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout;...
Page 90 2560 Series Barcode Scanner User Guide Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row...
Page 91 Chapter 2 Selecting Output Interface Capital Lock Type & Setting To send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted. Cap Lock Type Description Normal...
Page 92 2560 Series Barcode Scanner User Guide Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only.
Page 93 Chapter 2 Selecting Output Interface Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be “ON”.
Page 94 2560 Series Barcode Scanner User Guide ALT Composing By default, Alternate key composing is disabled. Select [Yes] to allow emulating Alternate key code of a specific keyboard character. For example, [Alt] + [065] will be sent to host for the character “A”...
Page 95: Inter-Character Delay
Chapter 2 Selecting Output Interface 2.4.3 INTER-CHARACTER DELAY By default, the inter-character delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be.
Page 96: Rs-232 Via Bt Cradle
2560 Series Barcode Scanner User Guide 2.5 RS-232 VIA BT CRADLE Use the RS-232 cable to connect the scanner via BT Cradle to the serial port of PC, and connect the power supply cord. The associated RS-232 parameters must match those configured on the computer.
Page 97: Data Bits
Chapter 2 Selecting Output Interface 4800 bps 2400 bps 1200 bps 600 bps 2.5.3 DATA BITS *8 bits 7 bits 2.5.4 PARITY *No parity Even Update...
Page 98: Stop Bit
2560 Series Barcode Scanner User Guide 2.5.5 STOP BIT 2 stop bits *1 stop bit 2.5.6 FLOW CONTROL By default, there is no flow control in use. Select the flow control (handshake) method. Options Description No flow control Scanner Ready The scanner will activate the RTS signal upon powering on.
Page 99: Inter-Character Delay
Chapter 2 Selecting Output Interface 2.5.7 INTER-CHARACTER DELAY By default, the inter-character delay is zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time. Such delay time is inserted between every character being transmitted. The longer the delay time is, the slower the transmission speed will be.
Page 100: Ack/Nak Timeout
2560 Series Barcode Scanner User Guide 2.5.9 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times.
Page 101: Usb Hid Via Bt Cradle
Chapter 2 Selecting Output Interface 2.6 USB HID VIA BT CRADLE For USB HID, use the USB cable to connect the scanner via BT Cradle to the USB port of PC and connect the power supply cord. Run any text editor on your computer, and the scanned data will be transmitted to the computer.
Page 102: Activate Usb Hid & Select Keyboard Type
2560 Series Barcode Scanner User Guide 2.6.1 ACTIVATE USB HID & SELECT KEYBOARD TYPE When USB HID interface is activated, you will have to select a keyboard type to complete this setting. Activate USB HID & Select Keyboard Type… 1) Read the barcode above to activate USB HID and select a keyboard type.
Page 103: Keyboard Settings
Chapter 2 Selecting Output Interface 2.6.2 KEYBOARD SETTINGS Alphabets Layout  Digits Layout  Capital Lock Type  Capital Lock Setting  Alphabets Transmission  Digits Transmission  Alphabets Layout By default, the alphabets layout is set to normal mode, also known as the standard English layout. Select French or German keyboard layout if necessary.
Page 104 2560 Series Barcode Scanner User Guide US Keyboard Style – Normal QWERTY layout, which is normally used in western countries.  Select “Lower Row” for the “Digits Layout” setting for the upper row is for special characters. French Keyboard Style – AZERTY French layout;...
Page 105 Chapter 2 Selecting Output Interface Digits Layout Select a proper layout that matches the alphabets layout. The scanner will make adjustments according to this setting. Options Description Normal Depends on the [Shift] key or [Shift Lock] setting Lower Row For QWERTY or QWERTZ keyboard Upper Row For AZERTY keyboard *Normal...
Page 106 2560 Series Barcode Scanner User Guide Capital Lock Type & Setting To send the alphabets with correct case, the scanner needs to know the status of Caps Lock on the keyboard. Incorrect settings may result in reversed case of the alphabets being transmitted.
Page 107 Chapter 2 Selecting Output Interface Alphabets Transmission By default, the alphabets transmission is case-sensitive, meaning that the alphabets will be transmitted according to their original case, the status of Caps Lock on the keyboard, as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted according to the status of Caps Lock on the keyboard only.
Page 108: Inter-Character Delay
2560 Series Barcode Scanner User Guide Digits Transmission By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric Keypad” if you wish to use the keys on the numeric keypad. Numeric Key *Alphanumeric Key Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard should be "ON".
Page 109: Inter-Function Delay
Chapter 2 Selecting Output Interface 2.6.4 INTER-FUNCTION DELAY By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 254 in units of millisecond, to match the computer response time of the keyboard interface. Such delay time is inserted between every function code (0x01 ~ 0x1F) being transmitted.
Page 110: Usb Virtual Com Via Bt Cradle
2560 Series Barcode Scanner User Guide 2.7 USB VIRTUAL COM VIA BT CRADLE Use the USB cable to connect the scanner via BT Cradle to the USB port of PC and connect the power supply cord. You may run HyperTerminal.exe on your computer, and the scanned data will be transmitted to the computer.
Page 111: Ack/Nak Timeout
Chapter 2 Selecting Output Interface 2.7.4 ACK/NAK TIMEOUT By default, the scanner sends data to the host without waiting for an ACK/NAK response before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If no response within the specified period of time, the scanner will attempt to send the same data two more times.
Page 112 2560 Series Barcode Scanner User Guide Enter Setup...
Page 113: Setting Up A Wpan Connection
Chapter 3 SETTING UP A WPAN CONNECTION The scanner can be configured to send data to a host computer wirelessly via the BT ® cradle, or to a notebook computer or PDA with Bluetooth wireless technology. Upon powering up, the scanner will be ready for establishing a WPAN connection. To establish a connection via BT Cradle after reading the Mac address label …...
Page 114: Connecting Via Cradle
2560 Series Barcode Scanner User Guide 3.1 CONNECTING VIA CRADLE By default, the interface of BT cradle is set to “USB HID”. Use the interface cable to connect the scanner via the cradle to PC. You can have up to seven scanners connected to one computer at the same time.
Page 115: Change Interface
Chapter 3 Setting up a WPAN Connection 3.1.2 CHANGE INTERFACE If you want to change the interface cable of cradle, use one of the scanners to configure the interface-related settings and it will pass the new settings to the cradle, which will then initialize and pass the settings to any other connected scanners.
Page 116: Configure Related Settings
2560 Series Barcode Scanner User Guide 3.1.3 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default, this feature is enabled, meaning the scanner will listen to the wireless network at a reduced rate. *Enable Disable Enter Setup...
Page 117: Change Interface
Chapter 3 Setting up a WPAN Connection BLUETOOTH 3.2 CONNECTING VIA DONGLE ® 3.2.1 CHANGE INTERFACE Below is the procedure to configure the scanner before establishing a WPAN connection ® via Bluetooth dongle. 1) Have the scanner read the “Enter Setup” barcode to enter the configuration mode. 2) Have the scanner read the desired interface barcode –...
Page 118: Configure Related Settings
2560 Series Barcode Scanner User Guide 3.2.2 CONFIGURE RELATED SETTINGS Sniff Mode (Power-saving) By default, this feature is enabled, meaning the scanner will listen to the wireless network at a reduced rate. *Enable Disable Note: When connecting more than two scanners to a notebook computer or PDA with ®...
Page 119 Chapter 3 Setting up a WPAN Connection Authentication When any changes are made to authentication and PIN code on the scanner side, you will have to remove the scanner from the paired device list (called unpairing) and go through the whole process to re-establish the connection.
Page 120 2560 Series Barcode Scanner User Guide Use random PIN No PIN required Note: When using BT HID, some device driver may not support pre-defined PIN code for authentication. In this case, make sure you have the scanner set to “No PIN or use random PIN”...
Page 121: Connect To Dongle
Chapter 3 Setting up a WPAN Connection 3.2.3 CONNECT TO DONGLE The procedure goes through associating devices for establishing a WPAN connection, which is pretty much the same except for the software you are using. If your computer is ® ®...
Page 122 2560 Series Barcode Scanner User Guide Turn on the scanner with correct WPAN settings, such as select BT SPP or BT HID, broadcasting enabled, authentication enabled, and PIN code specified, etc. Select the check box of [My device is set up and ready to be found] on your computer.
Page 123 Chapter 3 Setting up a WPAN Connection Click [Next]. Enter the passkey for authentication, which must be exactly the same as configured for the scanner. Update...
Page 124 2560 Series Barcode Scanner User Guide Click [Next]. Wait for a few seconds for Windows to exchange passkeys. Enter Setup...
Page 125 Chapter 3 Setting up a WPAN Connection Note: When Bluetooth security is enabled without providing a pre-set PIN code, dynamic input of PIN code is supported. Click [Finish]. Scanner as BT SPP Slave Scanner as BT SPP Master Update...
Page 126 2560 Series Barcode Scanner User Guide Now the target scanner will be listed as shown below. You can have up to seven scanners connected to one computer at the same time. Note: When any changes are made to authentication and PIN code on the scanner side,...
Page 127 Chapter 3 Setting up a WPAN Connection BT SPP Connected BT SPP Disconnected Update...
Page 128: Secure Simple Pairing (Ssp)
2560 Series Barcode Scanner User Guide 3.2.4 SECURE SIMPLE PAIRING (SSP) ® Secure Simple Pairing (SSP), introduced in Bluetooth Core Specification 2.1 + EDR, is a new feature designed to ease the pairing process while keeping up the communication ®...
Page 129: Changing Symbology Settings
Chapter 4 CHANGING SYMBOLOGY SETTINGS In this chapter, a brief on the symbology settings is provided for your reference. Users can simply scan the setting barcodes below to disable/enable all symbologies. Enable Disable Settings for each particular symbology will be depicted as follows. IN THIS CHAPTER 4.1 Codabar ..............
Page 130: Codabar
2560 Series Barcode Scanner User Guide 4.1 CODABAR *Enable Disable 4.1.1 START/STOP CHARACTERS SELECTION Select one of the four different start/stop character pairs – * abcd/abcd abcd/tn*e ABCD/ABCD ABCD/TN*E Enter Setup...
Page 131: Start/Stop Transmission
Chapter 4 Changing Symbology Settings 4.1.2 START/STOP TRANSMISSION Decide whether to include the start/stop characters in the data being transmitted. Transmit Start/Stop Characters *Do Not Transmit 4.1.3 CLSI CONVERSION When enabled, the CLSI editing strips the start/stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character Codabar barcode.
Page 132: Code 25 – Industrial 25
2560 Series Barcode Scanner User Guide 4.2 CODE 25 – INDUSTRIAL 25 *Enable Disable 4.2.1 START/STOP PATTERN SELECTION This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
Page 133: Verify Check Digit
Chapter 4 Changing Symbology Settings 4.2.2 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Industrial 25 Check Digit *Do Not Verify 4.2.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Industrial 25 Check Digit...
Page 134: Code Length Qualification
2560 Series Barcode Scanner User Guide 4.2.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must ...
Page 135: Code 25 – Interleaved 25
Chapter 4 Changing Symbology Settings 4.3 CODE 25 – INTERLEAVED 25 *Enable Disable 4.3.1 START/STOP PATTERN SELECTION This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
Page 136: Verify Check Digit
2560 Series Barcode Scanner User Guide 4.3.2 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Interleaved 25 Check Digit *Do Not Verify 4.3.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted.
Page 137: Code Length Qualification
Chapter 4 Changing Symbology Settings 4.3.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must ...
Page 138: Code 25 – Matrix 25
2560 Series Barcode Scanner User Guide 4.4 CODE 25 – MATRIX 25 Enable *Disable 4.4.1 START/STOP PATTERN SELECTION This decides the readability of all 2 of 5 symbology variants. For example, flight tickets actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5 should set to "Interleaved 25".
Page 139: Verify Check Digit
Chapter 4 Changing Symbology Settings 4.4.2 VERIFY CHECK DIGIT Decide whether to verify the check digit. If incorrect, the barcode will not be accepted. Verify Matrix 25 Check Digit *Do Not Verify 4.4.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Matrix 25 Check Digit Do Not Transmit...
Page 140: Code Length Qualification
2560 Series Barcode Scanner User Guide 4.4.4 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must ...
Page 141: Start/Stop Transmission
Chapter 4 Changing Symbology Settings 4.5 CODE 39 *Enable Disable 4.5.1 START/STOP TRANSMISSION Decide whether to include the start/stop characters in the data being transmitted. Transmit Code 39 Start/Stop Characters *Do Not Transmit 4.5.2 VERIFY CHECK DIGIT Decide whether to verify check digit. If incorrect, the barcode will not be accepted. Verify Code 39 Check Digit *Do Not Verify...
Page 142: Transmit Check Digit
2560 Series Barcode Scanner User Guide 4.5.3 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Code 39 Check Digit Do Not Transmit 4.5.4 STANDARD/FULL ASCII CODE 39 Decide whether to support Code 39 Full ASCII that includes all the alphanumeric and special characters.
Page 143: Asterisks (*) As Data Characters
Chapter 4 Changing Symbology Settings 4.5.6 ASTERISKS (*) AS DATA CHARACTERS Decide whether to take asterisk (*) as part of the data. Enable *Disable 4.6 CODE 93 *Enable Disable 4.7 CODE 128 *Enable Disable 4.7.1 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality.
Page 144: Ean-8
2560 Series Barcode Scanner User Guide Normal 4.8 EAN-8 EAN-8 *Enable EAN-8 (No Addon) Disable EAN-8 Addon 2 Enable EAN-8 Addon 2 *Disable EAN-8 Addon 5 Enable EAN-8 Addon 5 *Disable Enter Setup...
Page 145: Convert To Ean-13
Chapter 4 Changing Symbology Settings 4.8.1 CONVERT TO EAN-13 Decide whether to expand the read EAN-8 barcode, as well as its addons, into EAN-13. After conversion, the data follows EAN-13 format and is affected by EAN-13  programming selections (e.g. Check Digit). Convert EAN-8 to EAN-13 *Do Not Convert...
Page 146: Ean-13
2560 Series Barcode Scanner User Guide 4.9 EAN-13 EAN-13 *Enable EAN-13 (No Addon) Disable EAN-13 Addon 2 Enable EAN-13 Addon 2 *Disable EAN-13 Addon 5 Enable EAN-13 Addon 5 *Disable Enter Setup...
Page 147: Isbn Conversion
Chapter 4 Changing Symbology Settings 4.9.1 ISBN CONVERSION Decide whether to convert the EAN-13 barcode, starting with 978 and 979, to ISBN. Convert EAN-13 to ISBN *Do Not Convert 4.9.2 ISSN CONVERSION Decide whether to convert the EAN-13 barcode, starting with 977 to ISSN. Convert EAN-13 to ISSN *Do Not Convert...
Page 148: Security Level
2560 Series Barcode Scanner User Guide 4.9.4 SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading EAN-13 barcodes. Normal *High Enter Setup...
Page 149: Gs1-128 (Ean-128)
Chapter 4 Changing Symbology Settings 4.10 GS1-128 (EAN-128) *Enable Disable 4.10.1 CODE ID TRANSMISSION Decide whether to include the Code ID (" ") in the data being transmitted. Transmit Code ID *Do Not Transmit 4.10.2 FIELD SEPARATOR (GS CHARACTER) Decide whether to apply a field separator (to convert the control character to human FNC1 readable character).
Page 150: Gs1 Formatting
2560 Series Barcode Scanner User Guide 4.10.3 GS1 FORMATTING Decide whether to enable GS1 formatting for GS1-128. Enable *Disable 4.10.4 APPLICATION ID MARK Decide whether to add an application ID mark (1 character) to the left (AIMark1) or right (AIMark2) of an application ID (AI) for the purpose of labeling it when formatting the GS1 data.
Page 151: Isbt 128
Chapter 4 Changing Symbology Settings 4.11 ISBT 128 *Enable Disable 4.11.1 ISBT CONCATENATION Decide whether to decode and concatenate pairs of ISBT barcodes. Auto-discriminate ISBT Concatenation  It decodes and concatenates pairs of ISBT barcodes immediately. If only a single ISBT barcode is present, the scanner must decode 10 times before transmitting its data to confirm that there is no additional ISBT barcode.
Page 152: Verify Check Digit
2560 Series Barcode Scanner User Guide 4.12 MSI Enable *Disable 4.12.1 VERIFY CHECK DIGIT Select one of the three calculations to verify check digit when decoding barcodes. If incorrect, the barcode will not be accepted. *Single Modulo 10 Double Modulo 10 Modulo 10 &...
Page 153: Code Length Qualification
Chapter 4 Changing Symbology Settings 4.12.3 CODE LENGTH QUALIFICATION To prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct barcode is read by qualifying the allowable code length. If "Max/Min Length" is selected, the maximum length and the minimum length must ...
Page 154: French Pharmacode
2560 Series Barcode Scanner User Guide 4.13 FRENCH PHARMACODE Enable *Disable 4.13.1 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit French Pharmacode Check Digit Do Not Transmit Enter Setup...
Page 155: Italian Pharmacode
Chapter 4 Changing Symbology Settings 4.14 ITALIAN PHARMACODE Enable *Disable 4.14.1 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit Italian Pharmacode Check Digit Do Not Transmit Update...
Page 156: Plessey
2560 Series Barcode Scanner User Guide 4.15 PLESSEY Enable *Disable 4.15.1 CONVERT TO UK PLESSEY Decide whether to change each occurrence of the character 'A' to character 'X' in the decoded data. Convert to UK Plessey *Do Not Convert 4.15.2 TRANSMIT CHECK DIGIT Decide whether to include the two check digits in the data being transmitted.
Page 157: Gs1 Databar (Rss Family)
Chapter 4 Changing Symbology Settings 4.16 GS1 DATABAR (RSS FAMILY) It is categorized into three groups: Group I — GS1 DataBar Omnidirectional (RSS-14)  GS1 DataBar Omnidirectional This group consists of the following:  GS1 DataBar Truncated  GS1 DataBar Stacked ...
Page 158: Gs1 Databar Omnidirectional (Rss-14)
2560 Series Barcode Scanner User Guide 4.16.2 GS1 DATABAR OMNIDIRECTIONAL (RSS-14) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable The settings below apply to Group I symbologies only: GS1 DataBar Omnidirectional  GS1 DataBar Truncated  GS1 DataBar Stacked ...
Page 159 Chapter 4 Changing Symbology Settings Transmit Check Digit Decide whether to include the check digit in the data being transmitted. *Transmit RSS-14 Check Digit Do Not Transmit Update...
Page 160: Gs1 Databar Expanded (Rss Expanded)
2560 Series Barcode Scanner User Guide 4.16.3 GS1 DATABAR EXPANDED (RSS EXPANDED) Enable RSS-14 & RSS Expanded (Groups I, II) *Disable The settings below apply to Group II symbologies only: GS1 DataBar Expanded  GS1 DataBar Expanded Stacked  Transmit Code ID Decide whether to include the Code ID in the data being transmitted.
Page 161: Gs1 Databar Limited (Rss Limited)
Chapter 4 Changing Symbology Settings 4.16.4 GS1 DATABAR LIMITED (RSS LIMITED) Enable RSS Limited (Group III) *Disable Transmit Code ID Decide whether to include the Code ID in the data being transmitted. *Transmit RSS Limited Code ID Do Not Transmit Transmit Application ID Decide whether to include the Application ID ("01") in the data being transmitted.
Page 162: Field Separator (Gs Character)
2560 Series Barcode Scanner User Guide 4.16.5 FIELD SEPARATOR (GS CHARACTER) Decide whether to apply a field separator (to convert the GS control character to human readable character). Enable Field Separator… 1) Read the barcode above to enable field separator.
Page 163: Gs1 Databar Security Level
Chapter 4 Changing Symbology Settings 4.16.8 GS1 DATABAR SECURITY LEVEL Security Level renders more decoding accuracy giving consideration to barcodes’ print quality. Decide the security level for reading GS1 DataBar barcodes. *High Normal Update...
Page 164: Telepen
2560 Series Barcode Scanner User Guide 4.17 TELEPEN Enable Telepen *Disable 4.17.1 TELEPEN OUTPUT – FULL ASCII/NUMERIC Decide whether to support Telepen in full ASCII code. By default, it supports ASCII mode. AIM Telepen (Full ASCII) includes all the alphanumeric and special characters.
Page 165: Upc-A
Chapter 4 Changing Symbology Settings 4.18 UPC-A UPC-A *Enable UPC-A (No Addon) Disable UPC-A Addon 2 Enable UPC-A Addon 2 *Disable UPC-A Addon 5 Enable UPC-A Addon 5 *Disable Update...
Page 166: Convert To Ean-13
2560 Series Barcode Scanner User Guide 4.18.1 CONVERT TO EAN-13 Decide whether to expand the read UPC-A barcode, as well as its addons, into EAN-13. After conversion, the data follows EAN-13 format and is affected by EAN-13  programming selections (e.g. Check Digit).
Page 167: Upc-E
Chapter 4 Changing Symbology Settings 4.19 UPC-E UPC-E *Enable UPC-E (No Addon) Disable UPC-E Addon 2 Enable UPC-E Addon 2 *Disable UPC-E Addon 5 Enable UPC-E Addon 5 *Disable Update...
Page 168: System Number Selection
2560 Series Barcode Scanner User Guide 4.19.1 SYSTEM NUMBER SELECTION Decide whether to decode the ordinary UPC-E barcodes only or both UPC-E0 and UPC-E1 barcodes. System number enabled for decoding UPC-E0 barcodes.  System number enabled for decoding UPC-E1 barcodes.
Page 169: System Number Transmission
Chapter 4 Changing Symbology Settings 4.19.3 SYSTEM NUMBER TRANSMISSION Decide whether to include the system number in the data being transmitted. Transmit UPC-E System Number *Do Not Transmit 4.19.4 TRANSMIT CHECK DIGIT Decide whether to include the check digit in the data being transmitted. *Transmit UPC-E Check Digit Do Not Transmit...
Page 170 2560 Series Barcode Scanner User Guide Enter Setup...
Page 171: Defining Output Format
Chapter 5 DEFINING OUTPUT FORMAT You may configure in which format the collected data will be output to the host computer. Barcode read by the scanner will be processed in the following sequence – 1) Perform character substitution on the data scanned. 2) Add Code ID Length Code...
Page 172: Character Substitution
2560 Series Barcode Scanner User Guide 5.2 CHARACTER SUBSTITUTION Character substitution is performed on every occurrence of the first character specified. If only one character is specified, every occurrence of that character in the barcode will be taken away. The first character will be replaced by the second character(s).
Page 173: Select A Set For Character Substitution
Chapter 5 Defining Output Format 5.2.1 SELECT A SET FOR CHARACTER SUBSTITUTION Configure Set 1 Configure Set 2 Configure Set 3 1) Read the barcode above to enable character substitution by set. For example, have the scanner read the “Set 1” barcode to configure the first set of character substitution.
Page 174: Symbologies For Character Substitution (All 3 Sets)
2560 Series Barcode Scanner User Guide 5.2.2 SYMBOLOGIES FOR CHARACTER SUBSTITUTION (ALL 3 SETS) By default character substitution will be performed on all symbologies. If the character substitution is not desired with one or more symbologies, read the “Do Not Apply”...
Page 175 Chapter 5 Defining Output Format Character Substitution for GS1-128 *Apply Do Not Apply Character Substitution for ISBT 128 *Apply Do Not Apply Character Substitution for EAN-8 (No Addon) *Apply Do Not Apply Character Substitution for EAN-8 Addon 2 *Apply Do Not Apply Character Substitution for EAN-8 Addon 5 *Apply Do Not Apply...
Page 176 2560 Series Barcode Scanner User Guide Character Substitution for EAN-13 (No Addon) *Apply Do Not Apply Character Substitution for EAN-13 Addon 2 *Apply Do Not Apply Character Substitution for EAN-13 Addon 5 *Apply Do Not Apply Character Substitution for French Pharmacode...
Page 177 Chapter 5 Defining Output Format Character Substitution for Industrial 25 *Apply Do Not Apply Character Substitution for Interleaved 25 *Apply Do Not Apply Character Substitution for Matrix 25 *Apply Do Not Apply Character Substitution for MSI *Apply Do Not Apply Character Substitution for Plessey *Apply Do Not Apply...
Page 178 2560 Series Barcode Scanner User Guide Character Substitution for GS1 DataBar *Apply Do Not Apply Character Substitution for Telepen *Apply Do Not Apply Character Substitution for UPC-A (No Addon) *Apply Do Not Apply Character Substitution for UPC-A Addon 2 *Apply...
Page 179 Chapter 5 Defining Output Format Character Substitution for UPC-E (No Addon) *Apply Do Not Apply Character Substitution for UPC-E Addon 2 *Apply Do Not Apply Character Substitution for UPC-E Addon 5 *Apply Do Not Apply Update...
Page 180: Prefix/Suffix Code
2560 Series Barcode Scanner User Guide 5.3 PREFIX/SUFFIX CODE By default, there is no prefix code, and [ENTER] or [CR] (Carriage Return) is configured to be suffix code. Up to 8 characters can be configured, for example, “Barcode_”, and will...
Page 181: Select Pre-Defined Code Id
Chapter 5 Defining Output Format 5.4 CODE ID Up to two characters for Code ID can be configured for each symbology. To make the Code ID configuration easier, the scanner provides five pre-defined Code ID sets that you can select one and make necessary changes on it. If “BT HID”, “USB HID”...
Page 182 2560 Series Barcode Scanner User Guide Code ID options Set 1 Set 2 Set 3 Set 4 Set 5 Code 39 Italian Pharmacode French Pharmacode Industrial 25 Interleaved 25 Matrix 25 Codabar Code 93 Code 128 ISBT 128 UPC-E EAN-8...
Page 183: Change Code Id
Chapter 5 Defining Output Format 5.4.2 CHANGE CODE ID 1) Read the barcode below to change code ID of a specific symbology. 2) Read the “Hexadecimal Value” barcode on page 228 for the desired character string. For example, read “4” and “4” for applying the character [D] for Code ID. 3) Read the “Validate”...
Page 184: Clear Code Id Settings
2560 Series Barcode Scanner User Guide Configure Code ID for Interleaved 25 Configure Code ID for Matrix 25 Configure Code ID for Configure Code ID for Plessey Configure Code ID for Telepen Configure Code ID for UPC-A Configure Code ID for UPC-E 5.4.3 CLEAR CODE ID SETTINGS...
Page 185: Length Code
Chapter 5 Defining Output Format 5.5 LENGTH CODE A two-digit code representing the length of barcode data (character count) can be inserted in front of data being transmitted. Such "Length" code can be individually enabled or disabled for each symbology. Length Code for Codabar Apply *Do Not Apply...
Page 186 2560 Series Barcode Scanner User Guide Length Code for GS1-128 & GS1 DataBar Apply *Do Not Apply Length Code for ISBT 128 Apply *Do Not Apply Length Code for EAN-8 Apply *Do Not Apply Length Code for EAN-13 Apply *Do Not Apply...
Page 187 Chapter 5 Defining Output Format Length Code for Italian Pharmacode Apply *Do Not Apply Length Code for Industrial 25 Apply *Do Not Apply Length Code for Interleaved 25 Apply *Do Not Apply Length Code for Matrix 25 Apply *Do Not Apply Length Code for MSI Apply *Do Not Apply...
Page 188 2560 Series Barcode Scanner User Guide Length Code for Plessey Apply *Do Not Apply Length Code for Telepen Apply *Do Not Apply Length Code for UPC-A Apply *Do Not Apply Length Code for UPC-E Apply *Do Not Apply Enter Setup...
Page 189: Multi-Barcode Editor
Chapter 5 Defining Output Format 5.6 MULTI-BARCODE EDITOR The Multi-Barcode Editor allows you to decide the output sequence of a concatenation of barcodes. Up to five barcodes can be specified. When you enable this mode, it will force the scanner to apply Laser mode as the scan mode. Note: The Multi-Barcode Editor has nothing to do with Multi-Barcode Mode.
Page 190: Edit A Concatenation Of Barcodes
2560 Series Barcode Scanner User Guide 5.6.1 EDIT A CONCATENATION OF BARCODES Edit Output Sequence 1) Read the barcode above to start editing a concatenation of barcodes. 2) Code Type setting – read the “Hexadecimal Value” barcode on page 228 for Code Type of the (first) barcode.
Page 191: Activate The Concatenation Of Barcodes
Chapter 5 Defining Output Format 5.6.2 ACTIVATE THE CONCATENATION OF BARCODES By default, the output sequence editing of the concatenation of barcodes is not applied. When “Enforce Output Sequence” is enabled, all barcodes read by the scanner must meet with the criteria for the concatenation. If data is found excluded from all output sequence sets (= not meeting with the criteria), the scanner will not accept the reading, and therefore, data will not be transmitted.
Page 192: Removal Of Special Character
2560 Series Barcode Scanner User Guide 5.7 REMOVAL OF SPECIAL CHARACTER You can only specify 1 character, but it will remove every matching character encountered from the starting position of barcode data until a different character is met. For example, if it is configured to remove the character “0” (hex value is “30”), one or more zeros will be stripped off the barcode data “012345”...
Page 193: Applying Formats For Data Editing
Chapter 6 APPLYING FORMATS FOR DATA EDITING The scanner allows advanced data editing by applying user-configured editing formats. The whole processed data can be divided into fields by user-specified rules. These fields together with the user-configurable additional fields consist of the data actually sent to the host computer.
Page 194: Activating Editing Formats
2560 Series Barcode Scanner User Guide 6.1 ACTIVATING EDITING FORMATS 6.1.1 ACTIVATE EDITING FORMATS If you have already configured any editing format before, you may directly apply the editing format. If not, you must start with configuring an editing format first, and then, activate the editing format when it is desired in use.
Page 195: Exclusive Data Editing
Chapter 6 Applying Formats for Data Editing Editing Format 5 Enable *Disable 6.1.2 EXCLUSIVE DATA EDITING By default, only barcodes found meeting with the criteria are processed by the editing formats. Those found not meeting with the criteria are processed normally. When “Exclusive Data Editing”...
Page 196: How To Configure Editing Formats
2560 Series Barcode Scanner User Guide 6.2 HOW TO CONFIGURE EDITING FORMATS End Programming Format...
Page 197: Select Format To Configure
Chapter 6 Applying Formats for Data Editing 6.2.1 SELECT FORMAT TO CONFIGURE Start Programming Format Select one editing format (Format 1~5) and the parameters pertaining to the editing format can then be configured – applicable code type, data length, matching string & location, start position, field adjustment, total number of fields, field settings (field-dividing rule), additional fields, and field transmission sequence.
Page 198: Restore Default Format
2560 Series Barcode Scanner User Guide 6.2.2 RESTORE DEFAULT FORMAT You may select an existing editing format and have the defaults restored. The default settings of an editing format are listed below. Editing format Defaults Applicable Code Type Data Length...
Page 199: Configuring Format — Define Data Criteria
Chapter 6 Applying Formats for Data Editing 6.3 CONFIGURING FORMAT — DEFINE DATA CRITERIA Three applicable conditions can be configured to check whether the data read by the scanner can be processed by the particular editing format. Note: Data editing cannot be performed unless the three conditions are all met. 6.3.1 APPLICABLE CODE TYPE By default, barcodes of all the supported symbologies will be processed by any editing format, if having been configured and enabled.
Page 200 2560 Series Barcode Scanner User Guide Editing Format for Codabar *Apply Do Not Apply Editing Format for Code 39 *Apply Do Not Apply Editing Format for Code 93 *Apply Do Not Apply Editing Format for Code 128 *Apply Do Not Apply Editing Format for GS1-128 &...
Page 201 Chapter 6 Applying Formats for Data Editing Editing Format for ISBT 128 *Apply Do Not Apply Editing Format for EAN-8 *Apply Do Not Apply Editing Format for EAN-8 Addon 2 *Apply Do Not Apply Editing Format for EAN-8 Addon 5 *Apply Do Not Apply Editing Format for EAN-13...
Page 202 2560 Series Barcode Scanner User Guide Editing Format for EAN-13 Addon 2 *Apply Do Not Apply Editing Format for EAN-13 Addon 5 *Apply Do Not Apply Editing Format for French Pharmacode *Apply Do Not Apply Editing Format for Italian Pharmacode...
Page 203 Chapter 6 Applying Formats for Data Editing Editing Format for Interleaved 25 *Apply Do Not Apply Editing Format for Matrix 25 *Apply Do Not Apply Editing Format for MSI *Apply Do Not Apply Editing Format for Plessey *Apply Do Not Apply Editing Format for Telepen *Apply Do Not Apply...
Page 204 2560 Series Barcode Scanner User Guide Editing Format for UPC-A *Apply Do Not Apply Editing Format for UPC-A Addon 2 *Apply Do Not Apply Editing Format for UPC-A Addon 5 *Apply Do Not Apply Editing Format for UPC-E *Apply Do Not Apply...
Page 205 Chapter 6 Applying Formats for Data Editing Editing Format for UPC-E Addon 5 *Apply Do Not Apply Update...
Page 206: Data Length
2560 Series Barcode Scanner User Guide 6.3.2 DATA LENGTH The length must include prefix, suffix (0x0d by default), length code, etc. By default, barcodes of any length (character count) are eligible for data editing. You may specify a value from 0 to 254.
Page 207: Matching String & Location
Chapter 6 Applying Formats for Data Editing 6.3.3 MATCHING STRING & LOCATION By default, no matching string is specified, and therefore, it is disabled. You may enable this feature by specifying a matching string; up to four characters are allowed. When the Matching String Location is zero, the scanner will only check for the ...
Page 208: Field Adjustment
2560 Series Barcode Scanner User Guide 6.4.2 FIELD ADJUSTMENT You may apply equal length to all fields, if necessary. If data is found longer than specified, it will be truncated automatically. When data is found shorter, it will add “Space” (0x20) to field.
Page 209: Field Settings
Chapter 6 Applying Formats for Data Editing Five Fields Six Fields Note: The number of configurable fields is always one less than the total number of fields specified. The extra data characters beyond the last field configured will be automatically assigned to the next field. 6.4.4 FIELD SETTINGS Data eligible for editing formats is divided into fields by user-specified rules –...
Page 210 2560 Series Barcode Scanner User Guide If not dividing the field by a specific separator, you may divide it by a specified length. Read the barcode below to divide field 1 by length. Divide Field 1 by Length Read the “Decimal...
Page 211 Chapter 6 Applying Formats for Data Editing Field 3 Setting Read the barcode below to divide field 3 by a specified terminating string. Select Field Separator to Divide Field 3… Read the “Hexadecimal Value” barcode on page 228 for the desired character string. Read the “Validate”...
Page 212 2560 Series Barcode Scanner User Guide Field 4 Setting Read the barcode below to divide field 4 by a specified terminating string. Select Field Separator to Divide Field 4… Read the “Hexadecimal Value” barcode on page 228 for the desired character string.
Page 213 Chapter 6 Applying Formats for Data Editing Field 5 Setting Read the barcode below to divide field 5 by a specified terminating string. Select Field Separator to Divide Field 5… Read the “Hexadecimal Value” barcode on page 228 for the desired character string. Read the “Validate”...
Page 214 2560 Series Barcode Scanner User Guide Additional Fields Up to five additional fields can be created for each editing format; each of them is numbered from AF1 to AF5 accordingly.  If “BT HID”, “USB HID” or “Keyboard Wedge” is configured for interface, Key Type and Key Status will then become applicable.
Page 215: Pause Field Setting
Chapter 6 Applying Formats for Data Editing 6.4.5 PAUSE FIELD SETTING Pause Field Time You can limit the pause time interval (1~16). By default, it is set to 1 second. Pause Field Time 1~16 sec. (*1) Read the barcode above to specify the time interval for the Pause Field. (It is set to 1 by default.) Read the “Decimal...
Page 216: Configuring Format — Define Transmission Sequence
2560 Series Barcode Scanner User Guide 6.5 CONFIGURING FORMAT — DEFINE TRANSMISSION SEQUENCE After configuring the data fields and additional fields, you must now program the transmission sequence of these fields that comprise the final data. This field transmission sequence can be assigned in any desired order and fields can be assigned multiple times as well.
Page 217 Chapter 6 Applying Formats for Data Editing Additional Field 3 Additional Field 4 Additional Field 5 Pause Field Null Character Field 3) Read the “End” barcode to complete this setting. End Programming… Update...
Page 218: Programming Examples
2560 Series Barcode Scanner User Guide 6.6 PROGRAMMING EXAMPLES 6.6.1 EXAMPLE I Extract data from the 10th character to the 19th character... The editing format should be configured as follows: Read the “Enter Setup” barcode to enter the Configuration Mode.
Page 219: Example Ii
Chapter 6 Applying Formats for Data Editing 6.6.2 EXAMPLE II Extract the date code, item number, and quantity information from barcodes. Data in a barcode is encoded like this:  From the 1 character to the 6 character is the date code. ...
Page 220 2560 Series Barcode Scanner User Guide End Programming Format...
Page 221: Specifications
SPECIFICATIONS Optical Characteristics 2560 Scan Engine Non-contact type Optical Sensor CCD, 2500 pixels Light Source Visible red LED RF Characteristics WPAN Module Wireless PAN BT Class 2 compliance Coverage (line-of-sight) 100 meters with BT Cradle  Serial Port Profile (BT SPP) Interface Supported ...
Page 222 2560 Series Barcode Scanner User Guide Electrical Characteristics Battery Rechargeable Li-ion battery – 3.7 V, 800 mAh Power Adaptor Input AC 100~240 V, 50/60 Hz Output DC 5V, 2A (Cradle) DC 5V, 2A (Battery Charger) Operating Temperature 0 °C to 40 °C...
Page 223: Firmware Upgrade
Appendix I FIRMWARE UPGRADE You can only upgrade firmware of one scanner at a time. For example, you must turn off each of the rest scanners when there is more than one scanner connected to your computer. Note: In case it fails downloading due to low battery, make sure the targe scanner is loaded with good battery and the battery charge is enough.
Page 224 2560 Series Barcode Scanner User Guide Enter Setup Activate Cradle USB Virtual COM Update 5) Read the following barcodes in sequence for the scanner to enter the download mode. The scanner will respond with beeps to indicate it is ready for downloading.
Page 225 Appendix I Firmware Upgrade Note: The output interface remains unchanged as specified in step 3 (RS-232 or USB Virtual COM). For RS-232, the baud rate setting is still 115200 bps! BLUETOOTH USING DONGLE ® 1) Refer to 3.2.3 Connect to Dongle for the target scanner to accept the connection request from your computer.
Page 226 2560 Series Barcode Scanner User Guide  communication settings, select “RS-232” and the correct COM port for BT SPP interface.  Ignore the baud rate setting.  For the file option, click [Browse] to select the target file for firmware update.
Page 227: How To Upgrade Bt Cradle Firmware
Appendix I Firmware Upgrade HOW TO UPGRADE BT CRADLE FIRMWARE 1) Connect the interface cable, RS-232 or USB, between cradle and your computer. For USB Virtual COM, you may need to install its driver first! 2) Connect the power supply cord from the cradle to a proper power outlet. 3) Refer to 3.1.1 Connect to Cradle for the target scanner to connect to the cradle.
Page 228 2560 Series Barcode Scanner User Guide Kernel Program User Program 2560CradleKV*.shx 2560CradleUV*.shx  communication settings, select “RS-232” and the correct COM port for RS-232 or USB Virtual COM interface.  For RS-232, select 115200 bps for baud rate; for USB Virtual COM, ignore the baud rate setting.
Page 229: Host Serial Commands
Appendix II HOST SERIAL COMMANDS SERIAL COMMANDS TO THE SCANNER Purpose To disable the scanner. Remarks “D” Purpose To enable the scanner. Remarks “E” #@ nnnnnn <CR> Purpose To configure the scanner. Remarks nnnnnn – the six digits of command parameters. For example, “109952”...
Page 230: Example
2560 Series Barcode Scanner User Guide #@TRIGOFF<CR> Purpose To disable the software trigger Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” + “0x46” + “0x46” + “0x0d” #@TRIGON<CR> Purpose To enable the software trigger Remarks “0x23”...
Page 231: Bt Cradle Setup Barcodes & Serial Commands
Appendix II Host Serial Commands For the scanner to read the serial number and beep –  #@RDSN<CR> #@////<CR> Note: (1) For RS-232 or USB Virtual COM, you can only configure the first scanner that connects to cradle. To identify the scanner, you may send the serial command to have it respond with a beep.
Page 232: Bt Cradle Setup Barcodes
2560 Series Barcode Scanner User Guide BT CRADLE SETUP BARCODES Config<CR> Purpose To configure cradle. Here is the setup barcode for this serial command: Config Remarks A list of the current settings will be displayed. Run HyperTerminal.exe on your computer and change the settings one by one.
Page 233 Appendix II Host Serial Commands UseVariablePort<CR> Purpose To use variable Virtual COM port when connecting more than one cradle to PC via USB. Here is the setup barcode for this serial command: UseVariablePort Version<CR> Purpose To get the firmware versions. Here is the setup barcode for this serial command: Version GetID<CR>...
Page 234: Example
2560 Series Barcode Scanner User Guide EXAMPLE Without using the scanner to read the above setup barcodes for configuring the cradle, you may run HyperTerminal.exe on the host computer to send serial commands to the cradle via RS-232 or USB.
Page 235: Keyboard Wedge Table
Appendix III KEYBOARD WEDGE TABLE   "  Home    Down &  Left    Right PgUp Exec < PgDn > ENTER* Note: (1) ~: Digits of numeric keypad. (2) CR*/ENTER*: ENTER key on the numeric keypad. Update...
Page 236: Key Type & Status
2560 Series Barcode Scanner User Guide KEY TYPE & STATUS KEY TYPE If “BT HID”, “USB HID” or “Keyboard Wedge” is configured for interface, Key Type and Key Status will then become applicable. *Normal Scan Code KEY STATUS Decide whether or not to change key status when “Normal Key” is selected for Key Type.
Page 237: Example
Appendix III Keyboard Wedge Table EXAMPLE KEY TYPE = NORMAL For example, if you want to program the character “!” as the prefix code: Read the “Configure Prefix” barcode. Read the “Hexadecimal Value” barcode on page 228 for “2” and “1”. Read the “Validate”...
Page 238 2560 Series Barcode Scanner User Guide Enter Setup...
Page 239: Numeral Systems
Appendix IV NUMERAL SYSTEMS DECIMAL SYSTEM Decimal Validate the Values Validate Update Abort...
Page 240: Hexadecimal System
2560 Series Barcode Scanner User Guide HEXADECIMAL SYSTEM Hexadecimal Enter Setup...
Page 241: Ascii Table
Appendix IV Numeral Systems Validate the Values Validate ASCII TABLE " & < > Update Abort...
Page 242: Entering Pin Code For Authentication
2560 Series Barcode Scanner User Guide ENTERING PIN CODE FOR AUTHENTICATION USE PRESET PIN 1) In the configuration mode, read the barcode below to use a preset PIN for authentication. Use Preset PIN 2) Read one of the barcodes to specify the PIN code, in decimal or hexadecimal.
Page 243: Disable Authentication Or Use Random Pin
Appendix IV Numeral Systems DISABLE AUTHENTICATION OR USE RANDOM PIN In the configuration mode, read the barcode below to disable authentication (= No PIN) or use a random PIN for authentication. *No PIN or use random PIN Note: When using BT HID, some device driver may not support pre-defined PIN code for authentication.
Page 244 2560 Series Barcode Scanner User Guide Read the “Validate” barcode to complete this setting. Reject Random PIN Request When the random PIN is displayed on the target device while pairing, you can reject the PIN request by having the scanner read the “Validate” barcode.
Page 245: Keyboard Type One-Scan Barcode
Appendix V Keyboard Type One-Scan Barcode Appendix V KEYBOARD TYPE ONE-SCAN BARCODE KEYBOARD WEDGE PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) Update Abort...
Page 246 2560 Series Barcode Scanner User Guide PCAT (Spanish) PCAT (Portuguese) PS55 A01-1 PS55 A01-2 (Japanese) PS55 A01-3 PS55 001-1 PS55 001-81 PS55 001-2 PS55 001-82 Enter Setup...
Page 247 Appendix V Keyboard Type One-Scan Barcode PS55 001-3 PS55 001-8A PS55 002-1, 003-1 PS55 002-81, 003-81 PS55 002-2, 003-2 PS55 002-82, 003-82 PS55 002-3, 003-3 PS55 002-8A, 003-8A IBM 3477 Type 4 (Japanese) Update Abort...
Page 248 2560 Series Barcode Scanner User Guide PS2-30 IBM 34XX/319X, Memorex Telex 122 Keys User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) Enter Setup...
Page 249: Bluetooth Hid
Appendix V Keyboard Type One-Scan Barcode BLUETOOTH HID PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) PCAT (Spanish) Update Abort...
Page 250 2560 Series Barcode Scanner User Guide PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) Enter Setup...
Page 251: Remote Usb Hid
Appendix V Keyboard Type One-Scan Barcode REMOTE USB HID PCAT (US) PCAT (French) PCAT (German) PCAT (Italian) PCAT (Swedish) PCAT (Norwegian) PCAT (UK) PCAT (Belgium) PCAT (Spanish) Update Abort...
Page 252 2560 Series Barcode Scanner User Guide PCAT (Portuguese) PS55 A01-2 (Japanese) User-defined table PCAT (Turkish) PCAT (Hungarian) PCAT (Swiss German) PCAT (Danish) Enter Setup...

CipherLab 2560 User Manual

Quick Links

Related Manuals for CipherLab 2560

Summary of Contents for CipherLab 2560