Intec CS4000 User Manual page 137

Table of setting items in the device setup screen
Item
Letter O Style
1
Zero Character
Line Pitch
2
White Page Skip
CR Function
Line Length
3
Form Length
TOF Position
4
Left Margin
5
Fit to Letter
Text Height
Continuous Paper Mode
„ Color Setup
Item
Ink Simulation
UCR
CMY 100% Density
CMYK Conversion
Spot Color *1
*1: Displayed with CS5000 only.
z Shaded areas are factory-set values.
Details
Enable Specifies the style that replaces φ (9B)and ¥ (9D)
Disable with φ (ou) and Φ (zero).
Normal Specifies the style of 0 (zero).
Slashed SLASHED: SLASH ZERO
6 LPI Sets line space.
8 LPI
On Sets whether ejecting a blank sheet or not.
Off
CR Sets performance when CR code is received.
CR+LF
80 column Specifies the number of characters per line.
136 column
11 inch Specifies the length of paper.
11.7 inch
12 inch
0.0 inch Sets the position from the top edge of paper.
0.1 inch
~
1.0 inch
0.0 inch Sets the amount to shift the horizontal print start
0.1 inch position to the right.
~
1.0 inch
Enable Sets the printing mode that can fit print data,
Disable equivalent to 11 inches (66 lines), in the LETTER-
size printable area.
Same Sets height of a character.
Diff
On Sets to Landscape the edit direction of paper
Off supported by A3 printer.
z Shaded areas are factory-set values.
Details
Off Sets the ink simulation. This setting is enabled only
SWOP for PS language jobs.
ISO Coated
Japan
Low You can select the black plate (black) amount
Medium during color printing.
High Setting more black plate economizes on the toner
of the other three colors.
Enable Enables and disables 100% output over the CMY
Disable 100% shade values.
On If turned [Off], this is enabled to reduce the
Off print time if using large amounts of CMYK data
in the PostScript print data. However, the color
coordination of the print results will change.
Further, this menu setting is disabled if using the
ink simulation function.
White Displays the spot color information.
Clear The setting is enabled after the printer is restarted.
- 262 -
„ Panel Setup
Item
Near Life Status Enable
Disable
Near Life LED Enable
Disable
Idle Display Toner Gauge
Paper Size
Panel Brightness During Operating 5
to
31
Panel Brightness While Power Save 0
to
1
to
31
Panel Backlight Timer 10
to
30
to
300
Front Lamp Mode1
Mode2
Off
„ Time Setup
Item
Date Format yyyy/mm/dd
mm/dd/yyyy
dd/mm/yyyy
Time Zone -12:00
to
+0:00
to
+13:00
Daylight Saving On
Off
Time Setting 2000/01/01 00 :00
to
2009/01/01 00 :00
to
2091/12/31 23 :59
Table of setting items in the device setup screen
z Shaded areas are factory-set values.
Details
Sets the panel display control when a near life
warning occurs for the image drum, fuser unit, or
belt.
Sets the alarm lamp ON control when a near life
warning occurs for the toner, image drum, fuser
unit, belt, or waste toner box.
Sets the information displayed in the standby
screen.
Adjusts the brightness (backlight luminosity) of the
control panel LCD.
The set brightness is applied during control panel
operations.
Adjusts the brightness (backlight luminosity) of the
control panel LCD.
The set brightness is applied after the panel
backlight timer time has eplased from the last
operation.
Adjusts the time (s) from the last operation to
when the panel brightness (during power save) is
applied.
Sets the printer front lamp operations.
Mode1:
Lit when in standby mode, flashes slowly during
processing, and flashes rapidly when an error
occurs.
Mode2:
Lit when in standby mode, flashes slowly during
processing, and OFF when an error occurs.
Off:
Normally OFF.
z Shaded areas are factory-set values.
Details
Sets the date display mode.
Sets the time difference from GMT in 15-minute
units. If the time zone setting is changed, the tome
differences before and after the change is reflected
in the current time.
Memo
z The factory default is set to +9.00.
Sets whether to display summertime.
On:
Advances the current time by 1 hour.
Off:
Turns back the current time by 1 hour.
Sets the time.
Memo
z The factory default is to set the time.
- 263 -
1
2
3
4
5