Grizzly G0764Z Owner's Manual page 23

AA. Arbor Locking Pin ....................................... 1
AB. T-bolts M12-1.75 x 50.................................. 3
AC. Rip Fence Rail Stop Ring w/Set Screw ...... 1
AD. Locking Handles M10-1.5 x 12 ................... 2
AE. Knob Bolt M10-1.5 x 70 .............................. 1
AF. Rip Fence End Stop ................................... 1
AG. Adjustable Lock Handle M12-1.75 x 55 ...... 1
AH. T-Nut Plate M12-1.75 .................................. 1
AI. T-Nuts M8-1.25 ........................................... 5
AJ. 90° Stop Block............................................ 1
AK. T-Bolt M8-1.25 x 35 .................................... 1
AL. Pivot Bolt M8-1.25 ...................................... 1
AM. T-Slot Plate M8-1.25 ................................... 1
AN. Long Knobs M8-1.25 .................................. 2
AO. Knob Bolt M8-1.25 x 50 .............................. 3
AP. Knob Bolt M8-1.25 x 25 w/Nylon Tip .......... 1
AQ. Wire Clamps 3" .......................................... 2
AR. Dust Hood Return Spring ........................... 1
AS. Dust Port Adapter 4" .................................. 1
AB
AA
AE
AD
AH
AG
AL
AK
AN
AR
Figure 12. G0764Z Inventory 3.
Model G0764Z (Mfd. Since 10/15)
AC
AF
AI
AJ
AM
AO
AP
AQ
AS
Component Hardware (not shown)
—Combo Wrenches 30mm (Toolbox) ............... 2
—Open-End Wrench 19/22mm (Toolbox) ......... 1
—Open-End Wrench 36mm (Toolbox) .............. 1
—Lock Washers 12mm (Sliding Table) ............. 3
—Flat Washers 12mm (Sliding Table) ............... 3
—Hex Nuts M12-1.75 (Sliding Table) ................. 3
—B.H. Cap Screws M6-1 x 12 (Fence Scale) ... 3
—Flat Washers 6mm (Rip Fence Scale) ........... 4
—Hex Nut M6-1 (Rip Fence Scale) ................... 2
—Cap Screw M8-1.25 x 15 (Fence Rail) ........... 1
—Lock Washer 8mm (Fence Rail) .................... 1
—Flat Washer 12mm (Crosscut Table) ............. 1
—Flat Washers 8mm (Crosscut Brace) ............. 2
—Cap Screw M8-1.25 x 35 (Crosscut Fence) ... 1
—Lock Washer 8mm (Crosscut Fence) ............ 1
—Flat Washer 8mm, Fiber (Crosscut Fence) .... 1
—Fender Washer 8mm (Crosscut Fence)......... 2
—Fender Washers 20mm (Lower Guard Arm) . 2
—Hex Nuts M20-2.5 (Lower Guard Arm) .......... 2
—Hex Bolt M12-1.75 x 70 (Lower Guard Arm) .. 1
—Hex Nut M12-1.75 (Lower Guard Arm) ........... 1
—Cap Screws M8-1.25 x 25 (Arm Support) ...... 4
—Flat Washers 8mm (Arm Support) ................. 4
—Lock Washers 8mm (Arm Support) ............... 4
—Hex Bolt M10-1.5 x 30 (Arm Support) ............ 1
—90° Mounting Bracket (Arm Support) ............ 1
—B.H. Cap Screws M6-1 x 12 (Dust Coupler) .. 4
—Flat Washers 6mm ......................................... 5
—Lock Washers 6mm ....................................... 6
—Cap Screws M6-1 x 20 (Guard Cover) .......... 5
—Lock Washers 6mm (Guard Cover) ............... 3
—Flat Washers 6mm (Guard Cover) ................. 3
—Toolbox ........................................................... 1
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Qty
-21-