Siemens SIMOREG DC Master 6RA7028-6DS22 Operating Instructions Manual page 520

Parameter list
PNU Description
U664 Source for switchover to setpoint step S4
(2664)
0 = Binector B0000
*
1 = Binector B0001
etc.
U665 Setpoint for setpoint step S1
(2665)
U666 Setpoint for setpoint step S2
(2666)
U667 Setpoint for setpoint step S3
(2667)
U668 Setpoint for setpoint step S4
(2668)
11.71 Configuration of supplementary boards in board locations 2 and 3
U710 Initialize link to supplementary boards
(2710)
i001 Initialization of 1
*
letter)
i002 Initialization of 2
letter
Settings:
0 The link to supplementary boards is re-initialized. After the
configuration parameters for supplementary boards have been
changed, U710 must be set to 0 so that the new settings can
take effect.
The parameter is then set automatically to 1.
Note: Data transmission is interrupted while initialization is in
1 Deactivated
U711 Communications board parameter 1 (CB parameter 1)
(2711)
See documentation for installed COM BOARD.
*
This parameter is relevant only if a communications board is installed. The
validity of the setting is monitored by the CB. If the CB rejects the setting,
fault message F080 is displayed with fault value 5
Index 1 is used to parameterize the 1
index 2 to parameterize the 2
U712 Communications board parameter 2 (CB parameter 2)
(2712)
See U711
*
U713 Communications board parameter 3 (CB parameter 3)
(2713)
See U711
*
U714 Communications board parameter 4 (CB parameter 4)
(2714)
See U711
*
U715 Communications board parameter 5 (CB parameter 5)
(2715)
See U711
*
U716 Communications board parameter 6 (CB parameter 6)
(2716)
See U711
*
U717 Communications board parameter 7 (CB parameter 7)
(2717)
See U711
*
U718 Communication Board Parameter 8 (CB-Parameter 8)
(2718)
See U711
*
11-128
st
communications board (in slot with lower ID
nd
communications board (in slot with higher ID
progress.
st
CB (including CB behind TB) and
nd
CB.
Value range
[Unit]
Steps
All binector numbers
[SW 1.7 and later]
1
[SW 1.7 and later] 0.00 to 110.00
[%]
0.01%
[SW 1.7 and later] 0.00 to 110.00
[%]
0.01%
[SW 1.7 and later] 0.00 to 110.00
[%]
0.01%
[SW 1.7 and later] 0.00 to 110.00
[%]
0.01%
0 to 1
1
0 to 65535
1
0 to 65535
1
0 to 65535
1
0 to 65535
1
0 to 65535
1
0 to 65535
1
0 to 65535
1
0 to 65535
1
SIMOREG DC Master
02.00
No. indices See
Factory Change
setting (Access /
Type Status)
Ind: None P052 = 3
FS=0 P051 = 40
Type: L2 off-line
Ind: None P052 = 3
FS=10.00 P051 = 40
Type: O2 on-line
Ind: None P052 = 3
FS=25,00 P051 = 40
Type: O2 on-line
Ind: None P052 = 3
FS=40.00 P051 = 40
Type: O2 on-line
Ind: None P052 = 3
FS=100.00 P051 = 40
Type: O2 on-line
Ind: 2 P052 = 3
FS=1 P051 = 40
Type: O2 Offline
Ind: 2 P052 = 3
FS=0 Online
Type: O2
Ind: 2 P052 = 3
FS=0 Online
Type: O2
Ind: 2 P052 = 3
FS=0 Online
Type: O2
Ind: 2 P052 = 3
FS=0 Online
Type: O2
Ind: 2 P052 = 3
FS=0 Online
Type: O2
Ind: 2 P052 = 3
FS=0 Online
Type: O2
Ind: 2 P052 = 3
FS=0 Online
Type: O2
Ind: 2 P052 = 3
FS=0 Online
Type: O2
SIEMENS AG 6RX1700-0AD76
Operating Instructions