Honeywell VISTA-128FBPN Installation And Setup Manual page 124

VISTA-128FBPN Installation and Setup Guide
Operator Access Levels .....................................
Operator Codes Levels 3-5.................................9-1
Output Device Control Commands .................. B-1
Output Devices ..................................................3-22
OUTPUT PGM .......................................................
overvoltage protection......................................
PABX Access Code.............................................5-3
Panel Linking ................................................
Panic Button or Speedkey..................................5-9
Partitioned System..............................................2-1
Partitioning.................................................... 1-2,
Perimeter Type 03 ...............................................
Peripherals Devices ............................................1-1
Permanent Keypad Display Backlighting .......5-10
Phone Module Access Code ............................ix, 5-2
PLL out of Lock .................................................
polling loop ........................................................3-15
Polling Loop Current Draw...............................
Polling Loop Supervision .................................3-17
Power Failure .....................................................10-4
Power Unattained ..............................................
Power-Up in Previous State ...............................5-3
Prevent Zone XXX Bypass..................................5-4
Primary Format ....................................................5-5
Primary Phone Number ......................................5-4
Primary Subscriber's Account Number ............5-3
Printer Baud Rate ..............................................5-11
Printer Type........................................................5-11
Priority of Displays for Panel Linking ...............2-4
Program Modes ...................................................4-1
Program Notification Signal ...............................5-7
Programming Commands ................................. B-1
PROGRAMMING COMMANDS............................
Programming Entry Errors .................................4-1
Programming Overview ......................................4-1
Programming Partition-Specific Data Fields ....4-2
Programming Scheduling Options....................6-4
Programming System-Wide Data Fields ...........4-2
Quick Arm .....................................................5-3, 9-1
Quick Exit .....................................................ix, 5-1
Random time ..........................................................
Randomize AC Loss Report ...............................5-2
RCVR SETUP ERROR .......................................
Real-Time Clock ..................................................8-1
Recent Close........................................................
Refresh Feature ...................................................6-7
Regulatory Agency Statements ........................ A-1
Index-4
P
, 2-3
2-1
Q
R
Relay commands .................................................6-8
7-1
Relay Control Commands .................................. B-2
Relay Timeout XXX Minutes .............................5-11
Relay Timeout YYY Seconds............................5-11
Remote Keypad Sounder..................................3-24
4-3
Remote P/S Type 13 ............................................
3-10
REPORT CODE PROG..........................................
Reporting Formats ............................................3-10
Restrict Disarming...............................................6-1
RF Motion ............................................................
RF Motion (RM) Type 02......................................
RF Receiver Supervision Check-in Interval ......5-9
RF System Installation Advisories ..................3-19
RF System Operation and Supervision...........
2-1
RF Transmitter Check-in Interval.......................5-9
4-6
RF Transmitter Low Battery Reporting .............5-9
RF Transmitter Low Battery Sound ...................5-9
Ring Count ...........................................................
Ring Detection Count..........................................5-5
3-26
RINGER EQUIVALENCE......................................
RJ31X....................................................................
3-28
RLY VOICE DESCR...............................................
3-26
SCHEDULED CHANGE .........................................
Scheduled Check-in
Scheduled Download ..........................................7-4
Scheduling ...........................................................6-1
Scheduling Commands...................................... B-1
Scheduling Menu Mode ......................................6-4
Scheduling Menu Structure................................6-4
Secondary Format ...............................................5-5
Secondary Phone Number..................................5-4
Secondary Subscriber Account Number ..........5-7
Send Cancel If Alarm + Off ...............................5-11
4-1
serial number devices ...................................
Serial Number Polling Loop (DS) Type 08 ........
Serial Number Polling Loop (SL) Type 06.........
Sescoa/Radionics ................................................
Sescoa/Radionics Select ....................................5-5
Specifications ..................................................... C-1
Standard/Expanded Reporting Primary ............5-5
Standard/Expanded Reporting Secondary .......5-5
Standby Battery Size.........................................3-30
Supervised Fire (Without Verification) Type 09
Supervised RF ....................................................
Supervised RF (RF) Type 03...............................
Supervision Pulses for Communicator ...........5-13
Supervisory Messages......................................10-4
Suppress Transmitter Supervision Sound .....5-10
6-8
Swinger Suppression..........................................5-7
10-4
System Commands ............................................ B-1
System Communication......................................1-2
1-2
System Events Notify..........................................5-1
SYSTEM LO BAT ...............................................
System LoBat" ...................................................
S
............................................ 7-4
4-7
4-3
3-21
4-8
3-18
7-3
C-1
3-9
4-3
4-4
3-16
4-8
4-8
3-10
4-7
3-21
4-8
10-4
10-1