Honeywell VISTA-128FBP User Manual

Honeywell VISTA-128FBP User Manual

Commercial fire and burglary partitioned security systems with scheduling
Hide thumbs Also See for VISTA-128FBP:
Table of Contents

Advertisement

VISTA-128FBP
VISTA-250FBP
Commercial Fire and Burglary
Partitioned Security Systems
with Scheduling
User Guide
K0377V2 7/09 Rev. B

Advertisement

Table of Contents
loading

Summary of Contents for Honeywell VISTA-128FBP

  • Page 1 VISTA-128FBP VISTA-250FBP Commercial Fire and Burglary Partitioned Security Systems with Scheduling User Guide K0377V2 7/09 Rev. B...
  • Page 2 – 2 –...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS SYSTEM OVERVIEW ......5 ✴ Using the READY Key ....28 General ............5 DISPLAYING ALL ZONE A Partitioned System ........5 DESCRIPTORS.........29 Zones ............6 ✳ Using the READY Key ......29 Fire Protection ..........6 Burglary Protection ........6 BYPASSING PROTECTION ZONES..30 Carbon Monoxide Protection ......7 Using the BYPASS Key ....30...
  • Page 4 PANIC KEYS ........43 FIRE ALARM SYSTEM ......58 Using Panic Keys ........43 In Case Of Fire Alarm....... 58 RELAY CONTROL....... 44 Silencing a Fire Alarm ......58 Event Display Lock ........59 General Information........44 Fire Drill Test (Code + # + 69)....59 Executing..........
  • Page 5: System Overview

    Congratulations on your ownership of a Honeywell partitioned Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today. Honeywell is the world's largest manufacturer of security systems and millions of premises are protected by Honeywell systems.
  • Page 6: Zones

    System Overview (cont’d) Zones Your system's sensing devices have been assigned to various "zones." For example, the sensing device on your Entry/Exit door may have been assigned to zone 001, sensing devices on windows in the master bedroom to zone 002, and so on.
  • Page 7: Carbon Monoxide Protection

    System Overview (cont’d) Carbon Monoxide Protection Carbon monoxide (CO) protection is available with your system using the 5800CO Carbon Monoxide Detector. The 5800CO is a 3V battery powered wireless Carbon Monoxide Detector used with wireless alarm systems that support 5800 series devices.
  • Page 8: Device Timers

    System Overview (cont’d) Device Timers The system provides up to 20 "timers" that can be used to control various devices, such as lights or appliances. These timers are similar in concept to the individual appliance timers that might be purchased at a department store.
  • Page 9: Self-Help Feature

    System Overview (cont’d) Self-Help Feature Abbreviated user instructions are built into the system that can be easily viewed on the alpha keypad's message display screen. This feature will prove particularly useful if this manual is not conveniently accessible when you need to perform a system procedure with which you are not familiar.
  • Page 10: About The Keypads

    About The Keypads General IMPORTANT: If the keypad beeps rapidly upon entering the premises, it indicates that an alarm has occurred during your absence. LEAVE the premises IMMEDIATELY and CONTACT THE POLICE from a safe location nearby. Your keypads allow you to control all system functions. The keypads feature a telephone style (digital) keypad and a Liquid Crystal Display (LCD) that shows the nature and location of all occurrences.
  • Page 11: Functions Of The Keypad

    Functions of the Keypad Primary Fire Keypad 6160CR-2 IMPORTANT! When using the keypad to enter codes and commands, sequential key depressions must be made within 3 seconds of one another. If 3 seconds elapse without a key depression, the entry is aborted and must be repeated from its beginning.
  • Page 12 Functions of the Keypad (cont’d) ARMED AWAY STAY READY TEST BYPASS CODE CHIME INSTANT READY Burglary Keypad 6160 IMPORTANT! When using the keypad to enter codes and commands, sequential key depressions must be made within 3 seconds of one another. If 3 seconds elapse without a key depression, the entry is aborted and must be repeated from its beginning.
  • Page 13 Functions of the Keypad (cont’d) ALPHA DISPLAY WINDOW: A 2-line, 4 MAX: Arms in manner similar to 32-character Liquid Crystal Display (LCD). AWAY mode, but eliminates the entry Displays protection point identification and delay period, thus providing maximum system status, messages, user protection.
  • Page 14 Functions of the Keypad (cont’d) LED ALARM INDICATOR: (RED) Lit ✳ READY : When depressed prior to when any Fire Alarm exists in the system. arming the system, the keypad will display LED SILENCED INDICATOR: (AMBER) all open protection zones within the Lit when CODE + OFF is pressed.
  • Page 15: Entry/Exit Delays

    Entry/Exit Delays General Information Your system has installer-programmed time delays, known as exit delay and entry delay. Whenever you arm your system, exit delay gives you time to leave through the designated exit door without setting off an alarm. Exit delay begins immediately after entering any arming command, and applies to all modes of arming protection.
  • Page 16: Security Codes And Authority Levels

    Security Codes and Authority Levels General Information At the time of installation, you were assigned an authority level and a personal four-digit security code, known only to you and yours. The security code must be entered when arming and disarming the system. The authority level defines the system functions that you can perform.
  • Page 17: Authority Levels

    Security Codes and Authority Levels (cont’d) Authority Levels Authority levels define the system functions a particular user can perform. Depending on the authority assigned to you, there are certain system functions you may be prohibited from performing. In summary, there are six authority levels, each having certain system restrictions as shown below.
  • Page 18: General Rules On Authority Levels And Changes

    Security Codes and Authority Levels (cont’d) General Rules on Authority Levels and Changes • A user may not delete or change the user code of the SAME or HIGHER authority than which he is assigned. • A user may only ADD users to a LOWER authority level. •...
  • Page 19: To Add A User

    Security Codes and Authority Levels (cont’d) To Add a User IMPORTANT: Temporary users should not be shown how to use any system function they do not need to know (e.g. bypassing protection zones). CODE 1. Enter Master or Manager code and press the key.
  • Page 20 Security Codes and Authority Levels (cont’d) If you as a user have access to other partitions, the MULTI-ACCESS ? keypad will prompt for ability of this new user to 0 = NO , 1 = YES access (GOTO) those partitions. Press 0 (NO) or 1 (YES).
  • Page 21: To Change A User's Code

    Security Codes and Authority Levels (cont’d) To Change a User's Code CODE 1. Enter Master or Manager code and press the key + user number to be changed. 2. Enter the new code for that user. The system will recognize that the user number is ADD NEW USER? already in use and will prompt whether or not this 0 = NO , 1 = YES...
  • Page 22: To Delete A User

    Security Codes and Authority Levels (cont’d) To Delete a User CODE 1. Enter Master or Manager code and press the key + user number to be deleted. 2. Enter Master or Manager code first entered. The system will recognize that the User number OK TO DELETE is already in use and will prompt to confirm that 0 = NO , 1 = YES...
  • Page 23: Accessing Other Partitions

    Accessing Other Partitions To Access another Partition Each keypad is assigned a default partition for display purposes, and will show only that partition's information. But, if the user is authorized, a keypad in one partition can be used to perform system functions in other partitions by using the GOTO command.
  • Page 24: Master Keypad Operation

    Accessing Other Partitions (cont’d) Global Arming Notes: • When performing a Global Arm, if there are faults in any of the selected partitions, the system will enter a Summary Mode. Faulted zones in all the selected partitions will be displayed. These faults must be corrected or bypassed.
  • Page 25 Accessing Other Partitions (cont’d) The following is an example of what would be displayed for a fault condition on Zone 002 (Loading Dock Window) on Partition 1 (Warehouse) when logging on from a keypad on Partition 9: WHSE DISARMED HIT ✴ FOR FAULTS This is the normal display that appears at Partition 1's keypad(s).
  • Page 26: Common Lobby Operation

    Accessing Other Partitions (cont’d) Common Lobby Operation When an installation consists of a partition that is shared by users of other partitions in a building, the shared partition may be assigned as a “common lobby” partition for the system. An example of this might be in a medical building where there are two doctors and a common entrance area.
  • Page 27: How User Codes Affect The Common Lobby

    Accessing Other Partitions (cont’d) How User Codes Affect the Common Lobby Codes with “Global” Arming If your code is given “global arming” when it is defined, the system displays a prompt that allows you to pick and choose the partitions to be armed or disarmed.
  • Page 28: Checking For Open Zones

    Checking For Open Zones Using the ✴ ✴ ✴ ✴ READY Key Before arming your system, all protected doors, windows and other protection zones must be closed or bypassed (see BYPASSING section). Otherwise the keypad will display a "Not Ready" message. Using the READY key will display all zones that are faulted, making it easier for you to secure any open zones.
  • Page 29: Displaying All Zone Descriptors

    Displaying All Zone Descriptors Using the ✳ ✳ ✳ ✳ READY Key The Alpha Keypads can also display all the zone descriptors that are programmed in your system. The abbreviated instructions for the READY key will appear first, followed by the zone descriptors. Displaying all descriptors is useful when you need to know the zone number of a particular zone, as when bypassing zones.
  • Page 30: Bypassing Protection Zones

    Bypassing Protection Zones Using the 6 BYPASS Key This key is used when you want to arm your system with one or more zones intentionally unprotected. Bypassed zones are unprotected and will not cause an alarm when violated while your system is armed. All bypasses are removed when an OFF sequence (security code plus OFF) is performed.
  • Page 31: Quick Bypass

    Bypassing Protection Zones (cont’d) Quick Bypass Your system allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. Note: All bypasses are removed when an OFF sequence (security code plus OFF) is performed. To use the Quick Bypass feature: BYPASS 1.
  • Page 32: Group Bypass

    Bypassing Protection Zones (cont’d) Group Bypass Your system allows you to easily bypass a group of zones without having to enter zone numbers individually. The system provides up to 15 groups. There is no limit to the number of zones that may be assigned to any one group. Check with your installer for a list of zones assigned to the group(s).
  • Page 33: Arming Perimeter Only

    Arming Perimeter Only (With Entry Delay ON) Using the 3 STAY key Use this key when you are staying home, but might expect someone to use the entrance door later. When armed in STAY mode, the system will sound an alarm if a protected door or window is opened, but you may otherwise move freely throughout the premises.
  • Page 34: Auto-Stay Arming

    Arming Perimeter Only (With Entry Delay ON) (cont’d) Auto-STAY Arming Auto-stay allows the system to automatically bypass certain zones if upon arming none of the entry/exit zones are faulted during the exit delay time (no one exits the premises). The system provides an option to set each burglary zone for Auto-stay.
  • Page 35: Arming Perimeter Only

    Arming Perimeter Only (With Entry Delay OFF) Using the 7 INSTANT Key Use this key when you are staying home and do not expect anyone to use the entrance door. When armed in INSTANT mode, the system will sound an alarm if a protected door or window is opened, but you may otherwise move freely throughout the premises.
  • Page 36: Arming All Protection

    Arming All Protection (With Entry Delay ON) Using the 2 AWAY Key Use this key when no one will be staying on the premises. When armed in AWAY mode, the system will sound an alarm if a protected door or window is opened, or if any movement is detected inside the premises. You may leave through the entrance door during the exit delay period without causing an alarm.
  • Page 37: Arming All Protection

    Arming all Protection (with Entry Delay OFF) Using the 4 MAXIMUM Key Use this key when the premises will be vacant for extended periods of time such as vacations, etc., or when no one will be moving through protected interior areas. When armed in MAXIMUM mode, the system will sound an alarm if a protected door or window is opened, or if any movement is detected inside the premises.
  • Page 38: Quick Exit

    Quick Exit Using the # + 9 Keys The Quick Exit feature allows you to exit the armed partition without having to disarm and then rearm the partition. To Quick Exit the premises: 1. Press the # key and then press the 9 key. 2.
  • Page 39: Disarming And Silencing Alarms

    Disarming and Silencing Alarms Using the 1 OFF Key The OFF key is used to disarm the system and to silence alarm and trouble sounds. See Summary of Audible Notification section for information that will help you to distinguish between FIRE and BURGLARY alarm sounds. IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the premises, but call the police from a nearby safe location.
  • Page 40: Using The Keyswitch

    Using the Keyswitch General Your system may be equipped with a keyswitch for use when arming and disarming a partition. A red and green light on the keyswitch plate indicate the status of your system as follows: Green Light: Lights when the system is disarmed and ready to be armed (no open zones).
  • Page 41: Chime Mode

    Chime Mode Using the 9 Key Your system can be set to alert you to the opening of a door or window while it is disarmed by using CHIME mode. When activated, three tones will sound at the Keypad whenever a protected perimeter door or window is opened, and the Not Ready message will be displayed.
  • Page 42: Viewing Alarm Company Messages

    Viewing Alarm Company Messages General Information Users of the system may periodically receive messages on their display screens from their monitoring agency or installer. When a message is waiting to be viewed, the message shown below will appear. MESSAGE. PRESS 0 FOR 5 SECS.
  • Page 43: Panic Keys

    Panic Keys (For Manually Activating Silent and/or Audible Alarms) Using Panic Keys Your system may have been programmed to use special key combinations to manually activate panic functions. The functions that might be programmed are Silent Emergency, Audible Emergency, and Personal Emergency. See your installer for the function(s) that may have been programmed for your system.
  • Page 44: Relay Control

    Relay Control General Information Your system may be set up using a relay so that a door (such as in a lobby) can be unlocked momentarily using a keypad command. Ask your installer if this has been done in our system. Executing To activate the relay enter your security code + [0] at the keypad.
  • Page 45: Using #70 Relay Menu Mode

    Using #70 Relay Menu Mode General Information Your system may be set up so that certain lights or other devices can be turned on or off by using the #70 command from a keypad. Ask your installer if this has been done in your system. To activate relays from a keypad, enter 4-digit security code + [#] +70.
  • Page 46: Using Schedules

    Using Schedules Delaying the Closing Time Your system's programmed schedules may automatically arm the system at a predetermined time. In the event a user must stay on the premises later than usual, users with master or manager authority levels can manually delay the automatic arming (closing) time up to 2 hours.
  • Page 47: Programming Temporary Schedules

    Using Schedules (cont’d) Programming Temporary Schedules Temporary schedules only affect the partition from which it is entered. Temporary schedules can be reused at later dates simply by scrolling (by pressing #) to the DAYS? prompt (described below) and activating the appropriate days.
  • Page 48 Using Schedules (cont’d) This is the prompt that actually activates the DAYS ? MTWTFSS temporary schedule, and allows the temporary HIT 0-7 X X schedule to be customized to a particular week's needs. To select the days that are to be activated, enter the desired number 1-7 (Monday = 1).
  • Page 49: Programming Device Timers

    Programming Device Timers General Information Device timers consist of an ON time and an OFF time, and selected days of the week in which they are active. There are up to 20 timers that can be used to control various devices, such as lights or appliances. Your installer will have programmed the appropriate devices into the system (up to 96 devices can be programmed).
  • Page 50 Programming Device Timers (cont’d) Enter the time you want the device turned on 00 ON TIME ? using 00:01 - 11:59 format. When the display 00:00 PM shows the desired time, press the * key to move to the AM/PM field. Press any key 0-9 to change the AM/PM indication.
  • Page 51: Randomize Output Device Times

    Programming Device Timers (cont’d) Randomize Output Device Times Devices in your system may be set for a random schedule, whereby they will turn on and off at different times each day. This is useful when going on vacation and you desire the turning on and off of the lights to the give the appearance of someone being home.
  • Page 52: Using #77 Instant Activation Mode

    Using #77 Instant Activation Mode The #77 Instant Activation Mode is used to activate outputs, bypass zones, etc. immediately upon exiting the #77 Mode. The actions that may be activated are relay commands, arm/disarm commands, zone bypassing commands, and open/close access conditions. Relay Commands Action Code Action Specifier...
  • Page 53 Using #77 Instant Activation Mode (cont’d) Bypass Commands Activation times 1 (Beginning), 2 (End), and 3 (During) are the only valid choices for bypass commands. If 3 (During) is selected for auto-bypassing, the system bypasses the zone(s) specified on a particular zone list at the beginning of the window and unbypasses them at the end of the window.
  • Page 54 Using #77 Instant Activation Mode (cont’d) Additional Commands Action Code Action Specifier Access Point Group Enable Group # Access Point Group Disable Group # To enter the Instant Activation Mode: Enter your security code; then press the [#] key followed by 77. Enter the code for the desired action.
  • Page 55: Event Log Procedures

    Event Log Procedures General Information To Display The Event Log The system has the ability to record 1. Enter CODE + [#] + [6] + [0] various events in a history log wherein 2. Select the display mode. each event is recorded in one of five RECENT: Displays only those events categories (listed below), with the time and occurring since last Event Log Clear...
  • Page 56 Event Logging Procedures (continued) 4. Use the [3] and [1] keys (for next and ALARM EVENT LOG previous categories respectively) to Displays time and date for zones which display the categories of events. have either caused an alarm or have been Press [8] to select a category and restored in the selected partition.
  • Page 57: Testing The System (To Be Conducted Weekly)

    Testing the System (To Be Conducted Weekly) Using the 5 TEST Key The TEST key puts your system into Burglary Walk Test mode, which allows each burglary protection point to be checked for proper operation. 1. Disarm the system and close all protected windows, doors, etc. READY should be displayed.
  • Page 58: Fire Alarm System

    Fire Alarm System Your fire alarm system (if installed) is on 24 hours a day, providing continuous protection. In the event of an emergency, the smoke and heat detectors automatically send signals to your Control, triggering a loud interrupting sound from the keypad and the optional exterior sounders. FIRE appears at your keypad and remains on until you silence the alarm.
  • Page 59: Event Display Lock

    Fire Alarm System (cont’d) Event Display Lock If several zones produce an alarm, trouble or supervisory, the system will display the first zone that produced an event. To display the other zone(s) in alarm or trouble, press the [*] key for each zone. Fire Drill Test (Code + # + 69) This test causes Notification Appliance Circuits to be activated for the purpose of conducting a fire drill or a bell test.
  • Page 60: Trouble Conditions

    Trouble Conditions Typical Trouble Displays The word CHECK or TRBL on the Keypad's display, accompanied by a rapid "beeping" at the Keypad, indicates there is a trouble condition in the system. To silence the beeping sound for trouble conditions, press any key. •...
  • Page 61: Power Failure

    CALL FOR SERVICE IMMEDIATELY if AC power cannot be restored. SERVICING INFORMATION Your local HONEYWELL dealer is the person best qualified to service your alarm system. Arranging some kind of regular service program with him is advisable. Your local HONEYWELL dealer is:...
  • Page 62: Emergency Evacuation

    Emergency Evacuation Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. 2.
  • Page 63: Maintaining Your System

    Maintaining Your System Taking Care of Your System The components of your security system are designed to be as free of maintenance as possible. However, there are some things you can do to make sure that your system is in reliable working condition. 1.
  • Page 64: Silencing Low Battery Warning Tones At The Keypad

    Maintaining Your System (cont’d) Silencing Low Battery Warning Tones at the Keypad The keypad’s warning tones can be silenced by performing an OFF sequence (code plus OFF key), but the Keypad's low battery message display will remain on as a reminder that you have a low battery condition in one or more of your sensors.
  • Page 65: Quick Guide To Fire System Functions

    Quick Guide to Fire System Functions ACTION PROCEDURE Displaying Event The system is programmed to lock the keypad display with the first event that occurred in priority order. Fire – highest priority Life Safety Troubles and Supervisory System Events (i.e. low battery) – lowest priority To display the next event, press the [*] key.
  • Page 66: Quick Guide To Burglary System Functions

    Quick Guide to Burglary System Functions FUNCTION PROCEDURE COMMENTS Check Zones Press [✱]. To view faulted zones when is system not ready Display All Press and hold [✱] for 5 seconds. Displays all alpha descriptors programmed by Descriptors installer. Arm System Enter code.
  • Page 67 Quick Guide to Burglary System Functions (cont’d) FUNCTION PROCEDURE COMMENTS Delete a User Enter master/manager code. Master and Manager level users can delete Press CODE [8]. users. Enter user no. to be deleted. A user can only be deleted by a user with Enter master/manager code.
  • Page 68: Summary Of Audible Notification

    Summary of Audible Notification (Alpha Display Keypads) SOUND CAUSE DISPLAY LOUD, FIRE ALARM FIRE is displayed; descriptor of zone in alarm is INTERRUPTED* displayed. Keypad & External LOUD, BURGLARY/AUDIBLE EMERGENCY ALARM is displayed; descriptor of zone in alarm is CONTINUOUS* ALARM also displayed.
  • Page 69 FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC CLASS B STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use.
  • Page 70 “FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
  • Page 71 CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT NOTICE AVIS The Canadian Department of Communications label L’étiquette du ministère des Communications du Canada identifies certified equipment. This certification means identifie le matériel homologué. Cette étiquette certifie que that the equipment meets certain telecommunications le matériel est conforme à...
  • Page 72 WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons.
  • Page 73: Index

    Index #70 command.........45 Delete User Code ........18 AC Loss ..........61 Descriptors..........29 Access Another Partition ....23 Device Timers ........8, 49 Access Control Commands....53 Disarm ........... 39 Action Code ..........52 DOC ............71 Action Specifier ........52 Duress ........... 17 Add a User ..........19 Duress Code.........
  • Page 74 Maximum..........6, 23 Relay Menu Mode .........45 MAXIMUM..........15 Replacing Batteries ......63 MAXIMUM mode........37 RF BUTTON ...........19 Memory of Alarm......7, 39 Routine Care .........64 Messages ..........42 Schedules...........7, 46 Modem Comm........61 Security Code .........16 MULTI-ACCESS ........20 Security Codes ........16 Not Ready ..........
  • Page 75 TWO YEAR LIMITED WARRANTY Honeywell International Inc., acting through its Security & Communications business (“Seller”), 2 Corporate Center Drive, Melville, New York 11747 warrants its products to be free from defects in materials and workmanship under normal use and service, normal wear and tear excepted, for 24 months from the manufacture date code; provided, however, that in the event the Buyer presents a proper invoice relating to the purchased product and such invoice bears a date later than the manufacture date, then Seller may at its discretion, reflect the warranty period as commencing at invoice date.
  • Page 76 NOTES...
  • Page 77 NOTES...
  • Page 78 NOTES...
  • Page 79 NOTES...
  • Page 80 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright © 2009 Honeywell International Inc. www.honeywell.com/security ÊK0377V2eŠ K0377V2 7/09 Rev. B...

This manual is also suitable for:

Vista-250fbp

Table of Contents

Save PDF