HP 10500 SERIES Configuration Manual page 411

routing information exchange PE to remote CE,
236
routing policy, 231
site, 2, 229
tunneling policy, 231
VPN instance, 3, 229
VPN target attribute, 4
VPN-IPv4 address, 3, 229
MPLS TE
administrative group, 93
advertising TE attribute, 91
affinity attribute, 93
assigning tunnel priority, 1 14
automatic route advertisement, 97
automatic route advertisement traffic forwarding
along tunnel, 1 15
BSB timeout (RSVP-TE), 96
calculating path, 91
concept, 91
configuring, 90, 101, 127
configuring (MPLS L3VPN), 154
configuring administrative group (CR-LSP), 1 1 1
configuring affinity attribute (CR-LSP), 1 1 1
configuring BFD for tunnel detection, 121
configuring bypass tunnel on PLR, 1 19
configuring CR-LSP backup, 1 17, 142
configuring CR-LSP reoptimization, 1 12
configuring CR-LSP route pinning, 1 1 1
configuring CSPF, 104
configuring explicit path, 105
configuring failed link timer, 1 16
configuring FRR, 1 18, 145
configuring FRR polling timer, 120
configuring IS-IS TE, 105
configuring label recording, 1 13
configuring loop detection, 1 13
configuring MPLS LSP ping, 121
configuring MPLS LSP tracert, 121
configuring node protection, 120
configuring OSPF, 104
configuring periodic LSP tracert, 123
configuring protection switching, 124
configuring route pinning (CR-LSP), 1 1 1
configuring route recording, 1 13
configuring RSVP-TE, 132
configuring RSVP-TE advanced features, 107
configuring RSVP-TE and BFD cooperation, 140
configuring RSVP-TE authentication, 1 10
configuring RSVP-TE GR, 1 10, 138
configuring RSVP-TE hello extension, 109
configuring RSVP-TE refresh mechanism, 108
configuring RSVP-TE reservation style, 107
configuring
confirmation, 109
configuring RSVP-TE state timer, 108
configuring static CR-LSP, 127
configuring traffic forwarding, 1 14
configuring traffic forwarding tuning parameter,
1 16
configuring tunnel constraints, 106
configuring tunnel dynamic signaling protocol,
103
configuring tunnel routing link metric, 1 17
configuring tunnel setup retry, 1 13
configuring tunnel traffic flow type, 1 17
Constraint-based Routed LSP. See MPLS TE:CR‐LSP
creating tunnel over static CR-LSP, 102
CR-LSP, 92
CR-LSP backup, 98
CR-LSP explicit route, 92
CR-LSP route pinning, 92
deploying FRR, 99
displaying, 124
enabling FRR on protected LSP, 1 18
establishing path, 91
establishing RSVP-TE tunnel, 107
forwarding packet, 92
FRR, 98
FRR protection, 99
implementing, 91
inspecting tunnel, 121
maintaining, 124
make-before-break (RSVP-TE), 94
path switching mode, 100
policy-based routing, 97
preemption, 92
protection switching, 100
protection switching mode, 100
protection switching triggering, 100
protocols and standards, 100
PS. See MPLS TE:protection switching
PSB timeout (RSVP-TE), 96
reoptimizing, 93
route pinning (CR-LSP), 92
R SB timeout (RSVP-TE), 96
RSVP refresh mechanism (RSVP-TE), 95
RSVP-TE, 93
RSVP-TE concept, 93
RSVP-TE GR, 96
RSVP-TE message, 94
RSVP-TE resource reservation style, 93
RSVP-TE soft state, 93
403
RSVP-TE resource reservation