HP 10500 SERIES Configuration Manual page 425

Hide thumbs Also See for 10500 SERIES:
Table of Contents

Advertisement

configuring tunnel dynamic signaling protocol
(MPLS TE), 103
configuring tunnel traffic flow type (MPLS TE), 1 17
creating tunnel over static CR-LSP (MPLS TE), 102
CR-LSP (MPLS TE), 92
CR-LSP backup (MPLS TE), 98
CR-LSP explicit route (MPLS TE), 92
deploying FRR (MPLS TE), 99
engineering (MPLS TE), 90, 127
establishing path (MPLS TE), 91
establishing RSVP-TE tunnel (MPLS TE), 107
forwarding (MPLS TE), 97
forwarding packet (MPLS TE), 92
FRR (MPLS TE), 98
FRR protection (MPLS TE), 99
implementing MPLS TE, 91
policy-based routing (MPLS TE), 97
preemption (MPLS TE), 92
protection switching (MPLS TE), 100
PSB timeout (RSVP-TE MPLS TE), 96
reoptimizing (MPLS TE), 93
route pinning (CR-LSP MPLS TE), 92
RSB timeout (RSVP-TE MPLS TE), 96
RSVP refresh mechanism (RSVP-TE MPLS TE), 95
RSVP-TE (MPLS TE), 93
RSVP-TE GR (MPLS TE), 96
RSVP-TE resource reservation style (MPLS TE), 93
RSVP-TE soft state (MPLS TE), 93
setting up LSP tunnel (RSVP-TE MPLS TE), 95
static route forwarding along tunnel (MPLS TE), 1 14
static routing (MPLS TE), 97
tunneling applications (MCE), 5
trapping (enabling MPLS), 78
triggering
configuring LSP policy (MPLS), 65
protection switching (MPLS TE), 100
troubleshooting
MPLS L2VPN, 227
MPLS TE, 162
no TE LSA generated (MPLS TE), 162
VPLS, 188
TTL
configuring LSR processing mode (MPLS), 71
sending back ICMP TTL exceeded messages
(MPLS), 72
tuning
configuring traffic forwarding parameter (MPLS
TE), 1 16
CR-LSP setup (MPLS TE), 1 1 1
tunnel setup (MPLS TE), 1 13
tunneling
applications (MCE), 5
assigning priority (MPLS TE), 1 14
configuring administrative group (CR-LSP MPLS TE),
1 1 1
configuring affinity attribute (CR-LSP MPLS TE), 1 1 1
configuring BFD for tunnel detection (MPLS TE),
121
configuring bypass tunnel on PLR (MPLS TE), 1 19
configuring constraints (MPLS TE), 106
configuring MCE route advertising (MPLS L3VPN),
29
configuring routing link metric (MPLS TE), 1 17
configuring RSVP-TE (MPLS TE), 132
configuring RSVP-TE GR (MPLS TE), 138
configuring setup retry (MPLS TE), 1 13
configuring traffic flow type (MPLS TE), 1 17
configuring VPN instance tunneling policy (IPv6
MPLS L3VPN), 351
configuring VPN instance tunneling policy (MPLS
L3VPN), 251
creating over static CR-LSP (MPLS TE), 102
establishing RSVP-TE (MPLS TE), 107
inspecting (MPLS TE), 121
make-before-break (RSVP-TE MPLS TE), 94
policy (MPLS L3VPN), 231
setting up LSP (RSVP-TE MPLS TE), 95
static route traffic forwarding (MPLS TE), 1 14
tuning setup (MPLS TE), 1 13
VC
configuring service instance (MPLS L2VPN), 222
creating Martini for service instance (MPLS
L2VPN), 202
creating Martini on Layer 3 interface (MPLS
L2VPN), 202
inspecting (MPLS L2VPN), 204
VLAN
AC packet encapsulation (VPLS), 166
configuring encapsulation (MPLS L2VPN), 200
PW packet encapsulation (VPLS), 166
VPLS
AC packet encapsulation, 166
binding service with VPLS instance, 172, 175
concept, 163
configuring, 163, 174
configuring BGP, 170
configuring BGP extension, 171
configuring BGP instance, 171
configuring instance attribute, 172
configuring LDP, 169
configuring LDP instance, 169
configuring MAC address learning, 172
417

Advertisement

Table of Contents
loading

Table of Contents