Download Print this page
   
1
2
Table of Contents
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428

Advertisement

Step
5.
Enter address family view.
6.
Allow the local AS number to
appear in the AS_PATH
attribute of a received route
and set the maximum number
of repetitions.
7.
Enable a peer or peer group
for an address family and
enable the exchange of BGP
routing information of the
address family.
8.
Add a peer into an existing
peer group.
9.
Configure the system to use
the local address as the next
hop of a route to be
advertised to a specified peer
or peer group.
10.
Configure the system to be the
RR and set a peer or peer
group as the client of the RR.
11.
Enable the Outbound Route
Filtering (ORF) capability for a
BGP peer or peer group.
12.
Enable route target filtering
for received VPNv4 routes.
13.
Enable route reflection
between clients.
14.
Specify the cluster ID of the
RR.
Command
ipv4-family vpnv4
l2vpn-family
vpls-family
peer { group-name | ip-address }
allow-as-loop [ number ]
peer { group-name | ip-address }
enable
peer ip-address group group-name
peer { group-name | ip-address }
next-hop-local
peer { group-name | ip-address }
reflect-client
peer { group-name | ip-address }
capability-advertise orf ip-prefix
{ both | receive | send }
policy vpn-target
reflect between-clients
reflector cluster-id { cluster-id |
ip-address }
260
Remarks
Use one of the commands as
needed.
For information about BGP-L2VPN
address family and VPLS address
family, see MPLS Command
Reference.
Optional.
By default, only IPv4 routing
information is exchanged between
BGP peers.
Optional.
Optional.
By default, the system uses the local
address as the next hop of a route
to be advertised to an EBGP peer.
NOTE:
In the inter-AS option C solution,
group-name
configure the peer {
ip-address
} next-hop-invariable
command on the RR for multi-hop
EBGP neighbors and reflector
clients to make sure the next hop of
a VPN route is not changed.
Optional.
By default, no RR or RR client is
configured.
Optional.
By default, the ORF capability is
disabled on a BGP peer or peer
group.
Optional.
Enabled by default.
Optional.
Enabled by default.
Optional.
Router ID of an RR in the cluster by
default.
|

Advertisement

Troubleshooting

Comments to this Manuals

Symbols: 0
Latest comments: