Menu 21: Second Motor Parameters - Emerson unidrive m200 User Manual

Safety Product Mechanical
information information installation
10.17

Menu 21: Second motor parameters

Parameter
21.001 M2 Maximum Reference Clamp
21.002 M2 Minimum Reference Clamp
21.003 M2 Reference Selector
21.004 M2 Acceleration Rate 1
21.005 M2 Deceleration Rate 1
21.006 M2 Motor Rated Frequency
21.007 M2 Motor Rated Current
21.008 M2 Motor Rated Speed
21.009 M2 Motor Rated Voltage
21.010 M2 Motor Rated Power Factor
21.011 M2 Number of Motor Poles*
21.012 M2 Stator Resistance
21.014 M2 Transient Inductance
21.015 Motor 2 Active
21.016 M2 Motor Thermal Time Constant 1
M2 Frequency Controller Proportional
21.017
Gain Kp1
M2 Frequency Controller Integral
21.018
Gain Ki1
M2 Frequency Controller Differential
21.019
Feedback Gain Kd1
21.022 M2 Current Controller Kp Gain
21.023 M2 Current Controller Ki Gain
21.024 M2 Stator Inductance
21.025 M2 Saturation Breakpoint 1
21.026 M2 Saturation Breakpoint 3
21.027 M2 Motoring Current Limit
21.028 M2 Regenerating Current Limit
21.029 M2 Symmetrical Current Limit
21.033 M2 Low Frequency Thermal Protection Mode
21.041 M2 Saturation Breakpoint 2
21.042 M2 Saturation Breakpoint 4
* When read via serial communications, this parameter will show pole pairs.
RW Read / Write RO Read only
ND No default value NC Not copied
156
Electrical Getting Basic Running the
installation started parameters
Range ( Ú )
OL
±VM_POSITIVE_REF_CLAMP Hz
±VM_NEGATIVE_REF_CLAMP2
A1.A2 (0), A1.Pr (1), A2.Pr (2), PrESEt (3), PAd
(4), rES (5), PAd.rEF (6)
±VM_ACCEL_RATE
±VM_ACCEL_RATE
0.00 to VM_SPEED_FREQ_REF_UNIPOLAR Hz
±VM_RATED_CURRENT A
0.0 to 80000.0 rpm
±VM_AC_VOLTAGE_SET V
0.00 to 1.00
Auto (0) to 32 (16)
0.0000 to 99.9999
0.000 to 500.000 mH
Off (0) or On (1)
1 to 3000 s
0.00 to 4000.00
0.000 to 600.000
0.00 to 5000.00 mH
±VM_MOTOR2_CURRENT_LIMIT %
±VM_MOTOR2_CURRENT_LIMIT %
±VM_MOTOR2_CURRENT_LIMIT %
0 to 1
Num Number parameter
PT Protected parameter
NV Media
Optimization
motor Card
Default ( Ö )
RFC-A OL
50Hz: 50.00 Hz
60Hz: 60.00 Hz
50Hz: 50.00 Hz
60Hz: 60.00 Hz
Maximum Heavy Duty Rating (11.032)
50 Hz: 1500.0 rpm
60 Hz: 1800.0 rpm
110 V drive: 230 V
200 V drive: 230 V
400 V drive 50Hz: 400 V
400 V drive 60Hz: 460 V
575 V drive: 575 V
690 V drive: 690 V
179 s
0.000 to 200.000 s/rad
0.00 to 655.35 s²/rad
0.00000 to
0.65535 1/rad
0.0 to 100.0 %
0.0 to 100.0 %
165.0 %
165.0 %
165.0 %
0.0 to 100.0 %
0.0 to 100.0 %
Bit Bit parameter Txt Text string
RA Rating dependent US User save
Advanced
Technical data Diagnostics
parameters
RFC-A
RW Num
0.00 RW Num
A1.A2 (0) RW Txt
5.0 RW Num
10.0 RW Num
RW Num
RW Num
50 Hz: 1450.0rpm
RW Num
60 Hz 1750.0 rpm
RW Num
0.85 RW Num
Auto (0) RW Num
0.0000 RW Num
0.000 mH RW Num
RO Bit
179 s RW Num
0.100 s/rad RW Num
0.10 s²/rad RW Num
0.00000 1/rad RW Num
20.00 RW Num
40.000 RW Num
0.00 mH RW Num
50.0 % RW Num
75.0 % RW Num
175.0 % RW Num
175.0 % RW Num
175.0 % RW Num
0 RW Num
0.0 % RW Num
0.0 % RW Num
Bin Binary parameter
PS Power-down save
Unidrive M200 / M201 User Guide
Issue Number: 4
UL Listing
Type
US
US
US
US
US
RA US
RA US
US
RA US
RA US
US
RA US
RA US
ND NC PT
US
US
US
US
US
US
RA US
US
US
RA US
RA US
RA US
US
US
US
FI Filtered
DE Destination