Emerson unidrive m200 User Manual page 116

Safety Product Mechanical
information information installation
Parameter
02.001 Post Ramp Reference
02.002 Ramp Enable
02.003 Ramp Hold
02.004 Ramp Mode Select
02.005 Disable Ramp Output
02.006 S Ramp Enable
02.007 Max Rate Of Change Of Acceleration
02.008 Standard Ramp Voltage
02.009 Deceleration Fail Detection Disable
02.010 Acceleration Rate Selector
02.011 Acceleration Rate 1
02.012 Acceleration Rate 2
02.013 Acceleration Rate 3
02.014 Acceleration Rate 4
02.015 Acceleration Rate 5
02.016 Acceleration Rate 6
02.017 Acceleration Rate 7
02.018 Acceleration Rate 8
02.019 Jog Acceleration Rate
02.020 Deceleration Rate Selector
02.021 Deceleration Rate 1
02.022 Deceleration Rate 2
02.023 Deceleration Rate 3
02.024 Deceleration Rate 4
02.025 Deceleration Rate 5
02.026 Deceleration Rate 6
02.027 Deceleration Rate 7
02.028 Deceleration Rate 8
02.029 Jog Deceleration Rate
02.030 Acceleration Rate Selected
02.031 Deceleration Rate Selected
02.032 Acceleration Rate Select Bit 0
02.033 Acceleration Rate Select Bit 1
02.034 Acceleration Rate Select Bit 2
02.035 Deceleration Rate Select Bit 0
02.036 Deceleration Rate Select Bit 1
02.037 Deceleration Rate Select Bit 2
02.038 Inertia Compensation Torque
02.039 Ramp Rate Units
02.040 S Ramp Percentage
02.041 S Ramp Set-up Mode
02.042 Maximum Rate Of Change Of Acceleration 1
02.043 Maximum Rate Of Change Of Acceleration 2
02.044 Maximum Rate Of Change Of Acceleration 3
02.045 Maximum Rate Of Change Of Acceleration 4
RW Read / Write RO Read only
ND No default value NC Not copied
116
Electrical Getting Basic Running the
installation started parameters
Range ( Ú )
OL
±VM_SPEED_FREQ_REF Hz
Off (0) or On (1)
FASt (0), Std (1), Std.bSt (2), FSt.bSt (3)
Off (0) or On (1)
0.0 to 300.0 s²/100Hz
±VM_DC_VOLTAGE_SET V
Off (0) or On (1)
0 to 9
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
0 to 9
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
0 to 8
0 to 8
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
0 to 1
0.0 to 50.0 %
0 to 2
0.0 to 300.0 s²/100 Hz
0.0 to 300.0 s²/100 Hz
0.0 to 300.0 s²/100 Hz
0.0 to 300.0 s²/100 Hz
Num Number parameter
PT Protected parameter
NV Media
Optimization
motor Card
Default ( Ö )
RFC-A OL
Off (0) or On (1)
Off (0)
Std (1)
Off (0) or On (1)
Off (0)
3.1 s²/100 Hz
110 V drive: 375 V
200 V drive: 375 V
400 V drive 50 Hz: 750 V
400 V drive 60 Hz: 775 V
575 V drive: 895 V
690 V drive: 1075 V
Off (0)
10.0 s
10.0 s
10.0 s
10.0 s
10.0 s
10.0 s
10.0 s
10.0 s
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
Off (0)
±1000.0 %
0.0 %
0.0 s²/100 Hz
0.0 s²/100 Hz
0.0 s²/100 Hz
0.0 s²/100 Hz
Bit Bit parameter Txt Text string
RA Rating dependent US User save
Advanced
Technical data Diagnostics
parameters
RFC-A
RO Num
On (1) RW Bit
RW Bit
RW Txt
Off (0) RW Bit
RW Bit
RW Num
RW Num
RW Bit
0 RW Num
5.0 s RW Num
5.0 s RW Num
5.0 s RW Num
5.0 s RW Num
5.0 s RW Num
5.0 s RW Num
5.0 s RW Num
5.0 s RW Num
0.2 s RW Num
0 RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
0.2 s RW Num
RO Num
RO Num
RW Bit
RW Bit
RW Bit
RW Bit
RW Bit
RW Bit
RO Num
0 RW Num
RW Num
0 RW Num
RW Num
RW Num
RW Num
RW Num
Bin Binary parameter
PS Power-down save
Unidrive M200 / M201 User Guide
UL Listing
Type
ND NC PT
US
US
US
US
US
US
RA US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
ND NC PT
ND NC PT
NC
NC
NC
NC
NC
NC
ND NC PT
US
US
US
US
US
US
US
FI Filtered
DE Destination
Issue Number: 4