Emerson unidrive m200 User Manual page 112

Safety Product Mechanical
information information installation
Parameter
01.001 Reference Selected
01.002 Pre-skip Filter Reference
01.003 Pre-ramp Reference
01.004 Reference Offset
01.005 Jog Reference
01.006 Maximum Reference Clamp
01.007 Minimum Reference Clamp
01.008 Negative Reference Clamp Enable
01.009 Reference Offset Select
01.010 Bipolar Reference Enable
01.011 Reference On
01.012 Reverse Select
01.013 Jog Select
01.014 Reference Selector
01.015 Preset Selector
01.016 Preset Selector Timer
01.017 Keypad Control Mode Reference
01.021 Preset Reference 1
01.022 Preset Reference 2
01.023 Preset Reference 3
01.024 Preset Reference 4
01.025 Preset Reference 5
01.026 Preset Reference 6
01.027 Preset Reference 7
01.028 Preset Reference 8
01.029 Skip Reference 1
01.030 Skip Reference Band 1
01.031 Skip Reference 2
01.032 Skip Reference Band 2
01.033 Skip Reference 3
01.034 Skip Reference Band 3
01.035 Reference In Rejection Zone
01.036 Analog Reference 1
01.037 Analog Reference 2
01.038 Percentage Trim
01.041 Reference Select Flag 1
01.042 Reference Select Flag 2
01.043 Reference Select Flag 3
01.045 Preset Select Flag 1
01.046 Preset Select Flag 2
01.047 Preset Select Flag 3
01.048 Preset Selector Timer Reset
01.049 Reference Selected Indicator
01.050 Preset Selected Indicator
01.051 Power-up Keypad Control Mode Reference
01.057 Force Reference Direction
01.069 Reference in rpm
01.070 Clamped Reference
01.071 Alternative Reference
01.072 Alternative Reference Enable
RW Read / Write RO Read only
ND No default value NC Not copied
112
Electrical Getting Basic Running the
installation started parameters
Range ( Ú )
OL
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
0.00 to 300.00 Hz
±VM_POSITIVE_REF_CLAMP Hz
±VM_NEGATIVE_REF_CLAMP1 Hz
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
A1.A2 (0), A1.Pr (1), A2.Pr (2), PrESEt (3), PAd (4),
rES (5), PAd.rEF (6)
0 to 400.0 s
±VM_SPEED_FREQ_USER_REFS Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
0.00 to VM_SPEED_FREQ_REF_UNIPOLAR Hz
0.00 to 25.00 Hz
0.00 to VM_SPEED_FREQ_REF_UNIPOLAR Hz
0.00 to 25.00 Hz
0.00 to VM_SPEED_FREQ_REF_UNIPOLAR Hz
0.00 to 25.00 Hz
Off (0) or On (1)
±VM_SPEED_FREQ_USER_REFS Hz
±VM_SPEED_FREQ_USER_REFS Hz
±100.00 %
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
Off (0) or On (1)
rESEt (0), LASt (1), PrESEt (2)
None (0), For (1), rEv (2)
±VM_SPEED_FREQ_REF rpm
±VM_SPEED_FREQ_REF Hz
±VM_SPEED_FREQ_REF Hz
Off (0) or On (1)
Num Number parameter
PT Protected parameter
NV Media
Optimization
motor Card
Default ( Ö )
RFC-A OL
50Hz: 50.00 Hz
60Hz: 60.00 Hz
0 to 2
0 to 9
1 to 6
1 to 8
Bit Bit parameter Txt Text string
RA Rating dependent US User save
Advanced
Technical data Diagnostics
parameters
Type
RFC-A
RO Num ND
RO Num ND
RO Num ND
0.00 Hz RW Num
1.50 Hz RW Num
RW Num
0.00 Hz RW Num
Off (0) RW Bit
0 RW Num
Off (0) RW Bit
RO Bit ND
RO Bit ND
RO Bit ND
A1.A2 (0) RW Txt
0 RW Num
10.0s RW Num
0.00 Hz RO Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.00 Hz RW Num
0.50 Hz RW Num
0.00 Hz RW Num
0.50 Hz RW Num
0.00 Hz RW Num
0.50 Hz RW Num
RO Bit ND
0.00 Hz RO Num
0.00 Hz RO Num
0.00 % RW Num
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
Off (0) RW Bit
RO Num ND
RO Num ND
rESEt (0) RW Txt
None (0) RW Txt
RO Num ND
RO Num ND
0.00 Hz RW Num
RO Bit ND
Bin Binary parameter
PS Power-down save
Unidrive M200 / M201 User Guide
Issue Number: 4
UL Listing
NC PT
NC PT
NC PT
US
US
US
US
US
US
US
NC PT
NC PT
NC PT
US
US
US
NC PT PS
US
US
US
US
US
US
US
US
US
US
US
US
US
US
NC PT
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC PT
NC PT
US
NC PT
NC PT
NC PT
NC PT
FI Filtered
DE Destination