Basic Parameters; Menu 0: Basic Parameters - Emerson unidrive m200 User Manual

Safety Product Mechanical
information information installation
6

Basic parameters

Menu 0 is used to bring together various commonly used parameters for basic easy set up of the drive. All the parameters in Menu 0 appear in other
menus in the drive (denoted by {...}). Menus 22 can be used to configure the parameters in Menu 0.
6.1

Menu 0: Basic parameters

Parameter
00.001 Minimum Reference Clamp
00.002 Maximum Reference Clamp
00.003 Acceleration Rate 1
00.004 Deceleration Rate 1
00.005 Drive Configuration
00.006 Motor Rated Current
00.007 Motor Rated Speed
00.008 Motor Rated Voltage
00.009 Motor Rated Power Factor
00.010 User Security Status
00.015 Jog Reference
00.016 Analog Input 1 Mode
00.017 Bipolar Reference Enable
00.018 Preset Reference 1
00.025 User Security Code
Power-up Keypad Control Mode
00.027
Reference
00.028 Ramp Mode Select
00.029 Ramp Enable
00.030 Parameter Cloning
00.031 Stop Mode
Dynamic V to F Select / Flux
00.032
Optimization Select
00.033 Catch A Spinning Motor
00.034 Digital Input 5 Select
00.035 Digital Output 1 Control
00.036 Analog Output 1 Control
00.037 Maximum Switching Frequency
00.038 Autotune
00.039 Motor Rated Frequency
00.040 Number of Motor Poles*
00.041 Control Mode
00.042 Low Frequency Voltage Boost
00.043 Serial Baud Rate
00.044 Serial Address
00.045 Reset Serial Communications
00.046 Brake Release Current Threshold
78
Electrical Getting Basic Running the
installation started parameters
Range
OL
±VM_NEGATIVE_REF_CLAMP1 Hz
±VM_POSITIVE_REF_CLAMP Hz
±VM_ACCEL_RATE s
±VM_ACCEL_RATE s
AV (0), AI (1), AV.Pr (2), AI.Pr (3), Preset (4), Pad
(5), Pad.Ref (6), E.Pot (7), torque (8), Pid (9)
±VM_RATED_CURRENT A
0.0 to 80000.0 rpm
±VM_AC_VOLTAGE_SET V
0.00 to 1.00
LEVEL.0 (0), ALL (1), r.only.0 (2), r.only.A (3),
Status (4), no.acc(5)
0.00 to 300.00 Hz
4-20.S (-6), 20-4.S (-5), 4-20.L (-4),
20-4.L (-3), 4-20.H (-2), 20-4.H (-1), 0-20 (0), 20-0
(1), 4-20.tr (2), 20-4.tr (3), 4-20 (4), 20-4 (5), Volt (6)
Off (0) or On (1)
±VM_SPEED_FREQ_REF Hz
0 to 9999
Reset (0), Last (1), Preset (2)
Fast (0), Std (1), Std.bst (2), Fst.bst (3)
None (0), rEAd (1), Prog (2), Auto (3), boot (4)
Coast (0), rp (1), rp.dc I (2), dc I (3), td.dc I (4),
dis (5), No.rp (6)
0 to 1
dis (0), Enable (1), Fr.Only (2), Rv.Only (3)
Input (0), th.Sct (1), th (2), th.Notr (3), Fr (4)
0 to 21
0 to 15
0.667 (0), 1 (1), 2 (2),
3 (3), 4 (4), 6 (5),
8 (6), 12 (7), 16 (8) kHz
0 to 2
0.0 to VM_SPEED_FREQ_REF_UNIPOLAR Hz
Auto (0) to 32 (16)
Ur.S (0), Ur (1), Fd (2),
Ur.Auto (3), Ur.I (4),
SrE (5)
0.0 to 25.0 %
300 (0), 600 (1), 1200 (2), 2400 (3), 4800 (4), 9600
(5), 19200 (6), 38400 (7), 57600 (8), 76800 (9),
115200 (10)
1 to 247
Off (0) or On (1)
0 to 200 %
NV Media
Optimization
motor Card
Default
(Ú)
RFC-A OL
50Hz default: 50.00 Hz
60Hz default: 60.00 Hz
Maximum Heavy Duty Rating
50Hz default:
1500.0 rpm
60Hz default:
1800.0 rpm
110V drive: 230 V
200V drive: 230 V
400V drive 50 Hz: 400 V
400V drive 60 Hz: 460 V
575V drive: 575 V
690V drive: 690 V
LEVEL.0 (0)
Off (0) or On (1)
2 (2), 3 (3), 4 (4),
6 (5), 8 (6), 12 (7),
16 (8) kHz
0 to 3
50Hz: 50.00 Hz
60Hz: 60.00 Hz
Ur.I (4)
Advanced
Technical data Diagnostics
parameters
(Ö)
RFC-A
0.00 Hz RW Num
RW Num
5.0 s RW Num
10.0 s RW Num
AV (0) RW Txt
RW Num
(11.032) A
50Hz default:
1450.0 rpm
RW Num
60Hz default:
1750.0 rpm
RW Num
0.85 RW Num
RW Num ND NC PT
1.50 Hz RW Num
Volt (6) RW Txt
Off (0) RW Bit
0.00 Hz RW Num
0 RW Num ND NC PT US
Reset (0) RW Txt
Std (1) RW Txt
On (1) RW Bit
None (0) RW Txt
rp (1) RW Txt
0 RW Num
dis (0) RW Txt
Input (0) RW Txt
0 RW
0 RW
3 (3) kHz RW Txt
0 RW Num
RW Num
Auto 0 RW Num
RW Txt
3.0 % RW Num
19200 (6) RW Txt
1 RW Num
Off (0) RW
50 % RW Num
Unidrive M200 / M201 User Guide
Issue Number: 4
UL Listing
Type
US
US
US
US
PT US
RA US
US
RA US
RA US
US
US
US
US
US
US
US
NC US
US
US
US
US
US
US
US
NC US
RA US
US
US
US
US
US
ND NC
US