Emerson unidrive m200 User Manual page 128

Safety Product Mechanical
information information installation
Parameter
05.001 Output Frequency
05.002 Output Voltage
05.003 Output Power
05.004 Motor Rpm
05.005 D.C. Bus Voltage
05.006 Motor Rated Frequency
05.007 Motor Rated Current
05.008 Motor Rated Speed
05.009 Motor Rated Voltage
05.010 Motor Rated Power Factor
05.011 Number Of Motor Poles*
05.012 Autotune
05.013 Dynamic V To F Select / Flux Optimization Select
05.014 Control Mode
05.015 Low Frequency Voltage Boost
05.017 Stator Resistance
05.018 Maximum Switching Frequency
05.019 High Stability Space Vector Modulation
05.020 Over Modulation Enable
05.024 Transient Inductance
05.025 Stator Inductance
05.026 High Dynamic Performance Enable
05.027 Enable Slip Compensation
05.028 Flux Control Compensation Disable
05.029 Saturation Breakpoint 1
05.030 Saturation Breakpoint 3
05.031 Voltage Controller Gain
05.032 Torque Per Amp
05.033 Slip Compensation Limit
05.034 Percentage Flux
05.035 Auto-switching Frequency Change Disable
05.036 Slip Compensation Filter
05.037 Switching Frequency
05.040 Spin Start Boost
05.042 Reverse Output Phase Sequence
05.059 Maximum Deadtime Compensation
05.060 Current At Maximum Deadtime Compensation
05.061 Disable Deadtime Compensation
05.062 Saturation Breakpoint 2
05.063 Saturation Breakpoint 4
05.074 Boost End Voltage
05.075 Boost End Frequency
05.076 Second Point Voltage
05.077 Second Point Frequency
05.078 Third point voltage
05.079 Third point frequency
05.080 Low acoustic noise enable
Change to maximum drive switching frequency
05.081
at low output current
05.082 Motor Rated Power
05.083 Voltage Shelving Disable
05.084 Low Frequency Slip Boost
* If this parameter is read via serial communications, it will show pole pairs.
RW Read / Write RO Read only
ND No default value NC Not copied
128
Electrical Getting Basic Running the
installation started parameters
Range ( Ú )
OL
±VM_SPEED_FREQ_REF Hz
±VM_AC_VOLTAGE V
±VM_POWER kW
±80000 rpm
±VM_DC_VOLTAGE V
0.00 to VM_SPEED_FREQ_REF_UNIPOLAR Hz
±VM_RATED_CURRENT A
0.0 to 80000.0 rpm
±VM_AC_VOLTAGE_SET V
0.00 to 1.00
Auto (0) to 32 (16)
0 to 2
0 to 1
Ur.S (0), Ur (1),
Fd (2), Ur.Auto (3),
Ur.I (4), SrE (5)
0.0 to 50.0 %
0.0000 to 99.9999
0.667 (0), 1 (1), 2 (2),
3 (3), 4 (4), 6 (5), 8 (6),
12 (7), 16 (8) kHz
Off (0) or On (1)
Off (0) or On (1)
0.000 to 500.000 mH
0.00 to 5000.00 mH
±150.0 %
Off (0) or On (1)
1 to 30
0.00 to 500.00 Nm/A
0.00 to 10.00 Hz
0 to 2
64 (0), 128 (1), 256 (2),
512 (3) ms
0.667 (0), 1 (1), 2 (2),
3 (3), 4 (4), 6 (5), 8 (6),
12 (7), 16 (8) kHz
0.0 to 10.0
Off (0) or On (1)
0.000 to 10.000 µs
0.00 to 100.00 %
Off (0) or On (1)
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
Off (0) or On (1)
Off (0) or On (1)
±VM_POWER kW
Off (0) or On (1)
0.0 to 100.0 %
Num Number parameter
PT Protected parameter
NV Media
Optimization
motor Card
RFC-A OL
50 Hz: 50.00 Hz, 60 Hz: 60.00 Hz
Maximum Heavy Duty Rating (11.032)
50 Hz: 1500.0 rpm
60 Hz: 1800.0 rpm
110 V drive: 230 V, 200 V drive: 230 V
400 V drive 50Hz: 400 V
400 V drive 60Hz: 460 V
575 V drive: 575 V
690 V drive: 690 V
0 to 3
Ur.I (4)
2 (2), 3 (3), 4 (4), 6 (5),
8 (6), 12 (7), 16 (8) kHz
Off (0)
Off (0)
Off (0) or On (1)
100.0 %
0.0 to 100.0 %
0.0 to 100.0 %
5.00 Hz
0.0 to 150.0 %
128 (1) ms
2 (2), 3 (3), 4 (4), 6 (5),
8 (6), 12 (7), 16 (8) kHz
0.0 to 100.0 %
0.0 to 100.0 %
50.0 %
50.0 %
55.0 %
55.0 %
75.0 %
75.0 %
Off (0)
Off (0)
0.0 %
Bit Bit parameter Txt Text string
RA Rating dependent US User save
Advanced
Technical data Diagnostics
parameters
Default ( Ö )
RFC-A
RO Num ND NC PT
RO Num ND NC PT
RO Num ND NC PT
RO Num ND NC PT
RO Num ND NC PT
RW Num
RW Num
50 Hz: 1450.0 rpm
RW Num
60 Hz: 1750.0 rpm
RW Num
0.85 RW Num
Auto (0) RW Num
0 RW Num
0 RW Num
RW Txt
3.0 % RW Num
0.0000 RW Num
3 (3) kHz RW Txt
RW Bit
RW Bit
0.000 mH RW Num
0.00 mH RW Num
Off (0) RW Bit
RW Num
Off (0) RW Bit
50.0 % RW Num
75.0 % RW Num
1 RW Num
RO Num ND NC PT
RW Num
RO Num ND NC PT
0 RW Num
RW Txt
RO Txt
1.0 RW Num
Off (0) RW Bit
0.000 µs RO Num
0.00 % RO Num
Off (0) RW Bit
0.0 % RW Num
0.0 % RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
RW Num
RW Bit
Off (0) RW Bit
0.00 kW RW Num
RW Bit
RW Num
Bin Binary parameter
PS Power-down save
Unidrive M200 / M201 User Guide
Issue Number: 4
UL Listing
Type
FI
FI
FI
FI
FI
RA US
RA US
US
RA US
RA US
US
NC
US
US
US
RA US
RA US
US
US
RA US
RA US
US
US
US
US
US
US
US
US
US
ND NC PT
US
US
NC PT US
NC PT US
US
US
US
US
US
US
US
US
US
US
US
RA
US
US
FI Filtered
DE Destination