Toshiba TOSVERT VF-PS1 Instruction Manual page 248

1. Basic parameter [3/4]
Communication
Title Function
No.
Motor electronic thermal protection
0600
level 1
Electronic thermal protection
0017
characteristic selection
0701 Current/voltage unit selection
0005 FM terminal meter selection
0006 FM terminal meter adjustment
0670 AM terminal meter selection
0671 AM terminal meter adjustment
0300 PWM carrier frequency
0301 Auto-restart control selection
Regenerative power ride-through
0302
control
0304 Dynamic braking selection
0308 Dynamic braking resistance
Allowable continuous braking
0309
resistance
*1: ⇒ For the adjustment range, see the table on page K-39.
*2: For 37kW and above, the carrier frequency is between 2.5 and 4.9kHz inclusive..
*3: Default values vary depending on the capacity. ⇒ See the table of K-47.
*4: Default setting value is adjusted for connection of frequency meters "QS60T". (Between FM and CCA: Approx. 3.6V) (Between AM and CCA: Approx. 3.6V)
Adjustment range
10~100%
Overload
Setting Motor type OL stall
protection
0 ○ (protect) × (not stall)
1 ○ (protect) ○ (stall)
Standard
× (not
2 × (not stall)
Motor
protect)
× (not
3 ○(stall)
protect)
4 ○ (protect) × (not stall)
5 ○ (protect) ○(stall)
× (not
VF Motor
6 × (not stall)
protect)
× (not
○(stall)
7
protect)
0:%
1:A (ampere)/V (volt)
0~76 *1
-
0~76 *1
-
2.5~6.0kHz (2.5~4.9kHz) *2
0:Disabled
1:At auto-restart after momentary stop
2:When turning ST on or off
3:1+2
4:At start-up
0:Disabled
1:Power ride-through
2:Deceleration stop during power failure
0:Deselect
1:Enabled (braking resistance overload detect)
2:Enabled (braking resistance overload not detect)
0.5~1000Ω
0.01~600.0kW
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum
Default setting
Write
setting unit
during
(Panel/Communi
= = =
running
cation) 500V 575V 690V
-50Hz -60Hz -50Hz
1/1 100 100 100 Enabled
0 0 0 0 Enabled
0 0 0
1/1 Enabled
1/1 0 0 0 Enabled
1/1 *4 *4 *4 Enabled
2 2 2
1/1 Enabled
1/1 *4 *4 *4 Enabled
0.1/0.1 *3 *3 *3 Enabled
1/1 0 0 0 Disabled
0 0 0
1/1 Disabled
1/1 0 0 0 Disabled
0.1/0.1 *3 *3 *3 Disabled
*3 *3 *3
0.01/0.01 Disabled
Vector
V/f Reference
control
●/● ● 5. 14
●/● 5. 14
●/● ● 5. 15
●/● ● 5. 16
●/● ● 5. 16
●/● ● 5. 16
●/● ● 5. 16
●/● ● 5. 17
●/● ● 5. 18.1
●/● ● 5. 18. 2
●/● ● 5. 19
●/● ● 5. 19
●/● ● 5. 19