Toshiba TOSVERT VF-PS1 Instruction Manual page 260

[16] Speed feedback/positioning control
Communication
Title
No.
0375 Number of PG input pulses
0376 Selection of number of PG input phases
0377 PG disconnection detection
0378 Number of RP terminal input pulses
0379 PID output dead band
*1: ⇒ For details, refer to Instruction Manual (E6581319) specified in Section 6.36.
*2: ⇒ For details, refer to Instruction Manual (E6581341) specified in Section 6.36.
*3: ⇒ For details, refer to Instruction Manual (E6581329) specified in Section 6.36.
[17] Motor constant
Communication
Title
No.
0400 Auto-tuning 1
0401 Slip frequency gain
0402 Auto-tuning 2
0405 Motor rated capacity (motor name plate)
0406 Motor rated current (motor name plate)
Motor rated rotational speed (motor name
0407
plate)
0410 Motor constant 1 (torque boost)
0411 Motor constant 2 (no load current)
0412 Motor constant 3 (leak inductance)
0413 Motor constant 4 (rated slip)
0415 Exciting strengthening coefficient
0416 Stall prevention factor
*1: Default values vary depending on the capacity. ⇒ See the table of K-47.
*2: If the speed of rotation is set at 10,000min
Function Adjustment range
12~9999
1:Single-phase input
2:Two-phase input
3:Two-phase input (Inversion of polarity)
0:Disabled
1:Enabled (with filter)
2:Enabled (Detection of momentary power
failure)
12~9999
0~100%
Function Adjustment range
0:No auto-tuning
1:Initialize motor constant (0 after execution)
2:Continue operation continued after
auto-tuning (0 after execution)
3:Auto-tuning by input terminal signal
4:Motor constant auto calculation (0 after
execution)
0~150%
0:Disabled
1:Self-cooled motor
2:Forced air-cooled motor
0.10~800kW
0.1~2000A
100~60000min-1 *2
0.0~30.0%
10~90%
0~200%
0.1~25.0%
100~130%
10~250
-1
or more, the error messages and
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum
setting unit
(Panel/Communi
=
cation) 500V
-50Hz
1/1 500
1/1 2
1/1 0
1/1 500
0
1/1
Sensorless vector/vector with sensor (●:Effective, -:Ineffective)
Minimum
setting unit
(Panel/Communi
=
cation) 500V
-50Hz
1/1 0
1/1 70
1/1 0
0.01/0.01 *1
0.1/0.1 *1
1/1 *1
0.1/0.1 *1
*1
1/1
0.1/0.1 *1
0.1/0.1 *1
1/1 100
1/1 100
(if the speed of rotation is set at 10,000min
Default setting
Write
Vector
during V/f
control
= =
running
575V 690V
-60Hz -50Hz
500 500 Disabled -/●
2 2 Disabled -/●
0 0 Disabled -/●
500 500 Disabled ●/●
0 0
Enabled -/●
Default setting
Write
Vector
during
control Constant
= =
running
575V 690V
-60Hz -50Hz
0 0 Disabled ●/●
70 70 Enabled ●/-
0 0 Disabled ●/●
*1 *1 Disabled ●/●
*1 *1 Disabled ●/●
*1 *1 Disabled ●/●
*1 *1 Enabled ●/●
*1 *1
Disabled ●/●
*1 *1 Disabled ●/●
*1 *1 Disabled ●/●
100 100 Disabled ●/●
100 100 Disabled ●/●
-1
) are displayed alternately.
Reference
- *1
- *1
- *1
● *2
● 6. 18 *3
V/f
Reference
- 6. 19
- 6. 19
- 6. 19
- 6. 19
- 6. 19
- 6. 19
- 6. 19
- 6. 19
- 6. 19
- 6. 19
- 6. 20
- 6. 20