IFM Electronic CR0403 Programming Manual page 227

ifm Programming Manual ecomatmobile
Index
J1939_TX............................................................................................. 153
J1939_TX_ENH ................................................................................... 154
J1939_TX_ENH_CYCLIC ................................................................... 156
J1939_TX_ENH_MULTI ...................................................................... 158
L
LED ...................................................................................................... 218
Libraries ................................................................................................. 30
Library ifm_CANopen_NT_Vxxyyzz.LIB................................................ 61
Library ifm_CR0403_V03yyzz.LIB ........................................................ 59
Library ifm_J1939_NT_Vxxyyzz.LIB ..................................................... 63
Library ifm_RAWCan_NT_Vxxyyzz.LIB ................................................ 60
Limitations for CAN in this device .......................................................... 38
Limitations for CAN J1939 in this device ............................................... 38
Limitations for CANopen in this device.................................................. 38
Link ...................................................................................................... 218
LSB ...................................................................................................... 218
M
MAC-ID ................................................................................................ 219
Master .................................................................................................. 219
MEM_ERROR ..................................................................................... 192
MEMCPY ............................................................................................. 193
Memory, available.................................................................................. 12
Misuse .................................................................................................. 219
MMI ...................................................................................................... 219
MRAM .................................................................................................. 219
MSB ..................................................................................................... 219
N
Network variables .................................................................................. 57
NMT ..................................................................................................... 219
Node .................................................................................................... 219
Node Guarding .................................................................................... 219
Note on wiring ........................................................................................ 25
Note the cycle time! ............................................................................... 32
Notizen • Notes • Notes ....................................................................... 229
O
Obj / object ........................................................................................... 220
Object directory .................................................................................... 220
OBV ..................................................................................................... 220
OHC ..................................................................................................... 195
OPC ..................................................................................................... 220
Operating hours counter ...................................................................... 195
Operating states .................................................................................... 35
Operational .......................................................................................... 220
OUTPUT .............................................................................................. 180
Output group Q0 (OUT0, OUT1) ........................................................... 20
Output group Q1 (OUT2, OUT3, OUT8, OUT9) .................................... 22
Output group Q2 (OUT4...OUT7) .......................................................... 23
Output group Q3 (OUT10, OUT11) ....................................................... 24
Output parameters ............................................................................... 183
Outputs
address assignment .................................................................................... 206
operating modes .......................................................................................... 209
Outputs (technology) ............................................................................. 18
Overview
documentation modules for ecomatmobile devices ....................................... 5
BasicController (CR0403) Runtime System V03.02
227
P
PC card ................................................................................................ 220
PCMCIA card ....................................................................................... 220
PDM ..................................................................................................... 220
PDO ..................................................................................................... 220
PDU ..................................................................................................... 221
Performance limits of the device ........................................................... 37
PERIOD ............................................................................................... 175
PES ...................................................................................................... 221
PGN ..................................................................................................... 221
Pictogram ............................................................................................. 221
Pictograms ............................................................................................... 6
PID controller ....................................................................................... 221
PLC configuration ..........................................................................43, 221
Please note! ............................................................................................. 9
Possible operating modes inputs/outputs ........................................... 207
Pre-Op ................................................................................................. 221
Previous knowledge............................................................................... 10
Process image ..................................................................................... 221
Process input values ........................................................................... 168
Programming notes for CODESYS projects ......................................... 31
Protective functions of the outputs ........................................................ 18
PWM .................................................................................................... 222
PWM outputs ......................................................................................... 55
PWM1000 ............................................................................................ 182
R
ratiometric ............................................................................................ 222
RAW-CAN ............................................................................................ 222
Reaction according to the operating mode of the output ...................... 19
Reaction of the outputs to overload or short circuit ............................... 19
Reaction when using PWM or CURRENT_CONTROL ........................ 19
Read back retain variables .................................................................... 57
Reinstall the runtime system ................................................................. 40
remanent .............................................................................................. 222
Reset ...................................................................................................... 35
Resistance measurement ...................................................................... 16
Response to system errors .................................................................. 203
Retain variables ..................................................................................... 56
ro .......................................................................................................... 222
RTC ...................................................................................................... 222
RUN state .............................................................................................. 36
Runtime system .............................................................................29, 222
rw ......................................................................................................... 222
S
SAE J1939 .................................................................................. 137, 223
Safety instructions ................................................................................... 9
Safety instructions about Reed relays .............................................25, 48
Save retain variables ............................................................................. 57
SD card ................................................................................................ 223
SDO ..................................................................................................... 223
Self-protection of the output .................................................................. 19
Self-test ................................................................................................ 223
Set up the programming system ........................................................... 42
Set up the programming system manually ............................................ 42
Set up the programming system via templates ..................................... 46
Set up the runtime system ..................................................................... 39
Set up the target .................................................................................... 43
SET_IDENTITY ................................................................................... 197
2015-04-01