Mitsubishi FX3U-20SSC-H User Manual page 178

FX -20SSC-H Positioning Block User's Manual
3U
m code OFF
Change command in operation
disabled
Speed change command in
positioning operation
Remaining distance operation
cancel command
Acceleration/deceleration time
change command
(Ver. 1.30 or later)
Ring operation rotation direction for absolute address
(Ver. 1.10 or later)
X-START(Input terminal)
Y-START(Input terminal)
m code number
Number of the table in operation
Positioning completion
READY/BUSY
Standby for remaining travel
distance at stop
During table operation
execution
Received target address (Ver. 1.20 or later)
Received target speed (Ver. 1.20 or later)
Current address (user)
Current address (pulse)
Real current address (user) (Ver. 1.20 or later)
Real current address (pulse) (Ver. 1.20 or later)
Operation speed present value
System of units (user unit)
Unit of measurement for the
user units
Position data magnification
Acceleration/deceleration
mode
STOP mode
Servo end check enabled/
disabled
Servo ready check enabled/
disabled
Ring counter setting
(Ver. 1.10 or later)
Pulse rate
Feed rate
Maximum speed
Acceleration time
Deceleration time
Servo end evaluation time
Ring counter upper limit value (Ver. 1.10 or later)
Positioning completion signal output waiting time
(Ver. 1.20 or later)
Acceleration time 2 (Ver. 1.30 or later)
Deceleration time 2 (Ver. 1.30 or later)
172
Operation command 1 BFM #518 b11
Operation command 1 BFM #518 b12
Operation command 1 BFM #518 b13
Operation command 2 BFM #519 b0
Operation command 2 BFM #519 b5
BFM #530
BFM #9
BFM #16
Status information BFM #28 b6
Status information BFM #28 b0
Status information BFM #28 b7
Status information BFM #28 b15
BFM #25,#24
BFM #27,#26
BFM #1,#0
BFM #3,#2
BFM #21,#20
BFM #23,#22
BFM #11,#10
Operation parameter 1 BFM #14000 b1,b0
Operation parameter 1 BFM #14000 b3,b2
Operation parameter 1 BFM #14000 b5,b4
Operation parameter 1 BFM #14000 b11
Operation parameter 1 BFM #14000 b15
Operation parameter 2 BFM #14002 b0
Operation parameter 2 BFM #14002 b1
Operation parameter 2 BFM #14002 b3
BFM #14005,#14004 BFM #14205,#14204 Positioning parameters
BFM #14007,#14006 BFM #14207,#14206 Positioning parameters
BFM #14009,#14008 BFM #14209,#14208 Positioning parameters
BFM #14018
BFM #14020
BFM #14032
BFM #14101,#14100 BFM #14301,#14300 Positioning parameters
BFM #14106
BFM #14108
BFM #14110
BFM Number
X-axis Y-axis
BFM #618 b11
BFM #618 b12
BFM #618 b13
BFM #619 b0
BFM #619 b5
BFM #630
- -
- -
BFM #109
BFM #116
BFM #128 b6
BFM #128 b0
BFM #128 b7
BFM #128 b15
BFM #125,#124
BFM #127,#126
BFM #101,#100
BFM #103,#102
BFM #121,#120
BFM #123,#122
BFM #111,#110
BFM #14200 b1,b0
BFM #14200 b3,b2
BFM #14200 b5,b4
BFM #14200 b11
BFM #14200 b15
BFM #14202 b0
BFM #14202 b1
BFM #14202 b3
BFM #14218
BFM #14220
BFM #14232
BFM #14306
BFM #14308
BFM #14310
9 Positioning Control
9.8 Multi-Speed Operation
Data type
Control data
Control data
Control data
Control data
Control data
Control data
Input terminal
Input terminal
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Monitor data
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters
Positioning parameters